BS EN 1129-1-1995 Furniture - Foldaway beds - Safety requirements and testing - Safety requirements《家具 折叠床 安全技术要求和检验方法 安全性要求》.pdf

《BS EN 1129-1-1995 Furniture - Foldaway beds - Safety requirements and testing - Safety requirements《家具 折叠床 安全技术要求和检验方法 安全性要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1129-1-1995 Furniture - Foldaway beds - Safety requirements and testing - Safety requirements《家具 折叠床 安全技术要求和检验方法 安全性要求》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 1129-1:1995 Furniture Foldaway beds Safety requirements and testing Part 1: Safety requirements The European Standard EN 1129-1:1995 has the status of a British StandardBSEN1129-1:1995 This British Standard, having been prepared under the directionof the Consumer Products and

2、Services Sector Board, was published under theauthority of the StandardsBoard and comes intoeffect on 15August1995 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference CCM/37 Draft for comment 91/35489 DC ISBN 0 580 24279 X Committees responsible for this

3、 British Standard The preparation of this British Standard was entrusted to Technical Committee CCM/37, Beds, cots and mattresses, upon which the following bodies were represented: British Steel Industry British Steel Industry (Wire Section) British Textile Confederation Consumer Policy Committee of

4、 BSI Department of Health Furniture Industry Research Association Institute of Trading Standards Administration National Bed Federation Limited National Fillings Trades Association National Health Service (Procurement Group) Royal College of Nursing Amendments issued since publication Amd. No. Date

5、CommentsBSEN1129-1:1995 BSI 09-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 1129-1 3BSEN1129-1:1995 ii BSI 09-1999 National foreword This Part of BSEN1129has been prepared by Technical Committee CCM/37 and is the English language version o

6、f EN1129-1:1995Furniture Foldaway beds Safety requirements and testing Part 1: Safety requirements published by the European Committee for Standardization (CEN). EN 1129-1 was produced as a result of international discussions in which the United Kingdom took an active part. A British Standard does n

7、ot purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publication referred to Corresponding British Stan

8、dard EN 1129-2:1995 BS EN 1129 Furniture Foldaway beds Safety requirements and testing Part 2:1995 Test methods Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6 and a back cover. This standard has been updated (see copyrig

9、ht date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1129-1 February 1995 ICS 97.140 Descriptors: Furnishings, furniture, beds, specifications, safety, mechanical strength, anch

10、orages, technical notices, assembling marking English version Furniture Foldaway beds Safety requirements and testing Part 1: Safety requirements Ameublement Lits rabattables Exigences de scurit et essais Partie 1: Exigences de scurit Mbel Klappbetten Sicherheitstechnische Anforderungen und Prfverfa

11、hren Teil 1: Sicherheitstechnische Anforderungen This European Standard was approved by CEN on 1995-01-02. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterati

12、on. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translati

13、on under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, N

14、etherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any form

15、 and by any means reserved in all countries to CEN and its members Ref. No. EN 1129-1:1995 EEN1129-1:1995 BSI 09-1999 2 Foreword This European Standard has been prepared by Technical Committee CEN/TC 207, Furniture, of which the secretariat is held by IBN. This European Standard shall be given the s

16、tatus ofa national standard, either by publication of an identical text or by endorsement, at the latest by August 1995, and conflicting national standards shall be withdrawn at the latest by August 1995. According to the CEN/CENELEC Internal Regulations, the following countries are bound to impleme

17、nt this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative reference 3 3 Definition 3 4 Safety and strength 3 4.

18、1 Construction 3 4.2 Folding fittings 3 4.3 Mounting of the foldable part to the frame 3 4.4 Strength and durability 3 4.5 Unintended closing 3 4.6 Unintended opening 3 5 Mounting of the bed to the building 4 6 Installation instructions 4 7 Marking 4 Annex A (informative) Foldaway beds: Test scheme

19、5 Annex B (normative) Calculation of the minimum number of screws for fixing points 6EN1129-1:1995 BSI 09-1999 3 1 Scope This Part of EN1129specifies requirements relating to the safety and the strength of foldaway beds for domestic use. The standard also covers the strength of wall fastenings where

20、 applicable. This standard does not specify the properties of the materials or electrical equipment used in the construction of foldaway beds. Folding beds, camping beds and convertible bed/chairs or settees are not covered by this standard. In Annex A (informative), the requirements are shown schem

21、atically in relation to the testing procedures. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dat

22、ed references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 1129-2:1995, Furniture Foldaway beds Safety re

23、quirements and testing Part 2: Test methods. 3 Definitions For the purposes of this standard, the following definition applies: 3.1 foldaway bed a foldaway bed (hereafter referred to as bed) is a bed whose sleeping surface is rotated about at least one horizontal axis when being positioned for use 4

24、 Safety and strength 4.1 Construction Exposed edges and protruding parts shall be rounded and free from burrs or sharp edges. There shall be no open-ended tubes. 4.2 Folding fittings There shall be no shear and pinching points unless they are secured against unintended access. When tested in accorda

25、nce with 5.4 of EN1129-2the folding fittings shall be such as to ensure that neither the opening nor the closing force shall vary by more than20% between the two measurements. 4.3 Mounting of the foldable part to the frame The folding mechanism shall be fastened to the structure by means which will

26、remain tight throughout the service life of the bed. The fasteners shall not loosen after testing in accordance with 5.4 of EN 1129-2. NOTEExperience has shown that a nut and bolt are satisfactory but an ordinary wood screw may not be. 4.4 Strength and durability When tested in accordance with 5.6 o

27、f EN 1129-2, neither the constructional elements nor the wall mounting structure shall have loosened nor shall there be any damage which will affect the function and safety of the bed. 4.5 Unintended closing When tested in accordance with 5.5.3 of EN 1129-2, the foldable part shall not close automat

28、ically, i.e. the supports shall not lift more than 5 mm from the floor. 4.6 Unintended opening The foldable part shall reclose automatically when opened up to a distance of150mm, measured from the top edge (see Figure6of EN 1129-2). The pressure force applied to the defined loading point (see Figure

29、6 of EN 1129-2) shall be greater than250N when tested in accordance with 5.5.4 of EN 1129-2. Either the opening force required shall be not less than20N or a positive retaining catch shall be provided which retains the bed firmly in the closed position and which can be released only by use of a manu

30、al security device, e.g. a key or a double action button. Locking mechanisms shall be constructed so that the operating force is at least50N. In the case of revolving elements, this force shall be applied tangentially at the point on the element furthest away from the axis of rotation. The opening e

31、nergy, measured at an opening angle of70 , shall not exceed10Nm 1)when measured in accordance with 5.4 of EN 1129-2. 1) This value is measured taking into account the mass of the bed and the opening speed or the energy resulting from this opening speed.EN1129-1:1995 4 BSI 09-1999 However, bed constr

32、uctions with an opening energy of up to60Nm 1)and gravity controlled beds with an opening energy of up to120Nm 1)(measured at an opening angle of70 in each case) are acceptable, providing the following conditions are satisfied. a) Opening Automatic closing after an opening length of250 mm; and weigh

33、t to be supported during the opening process not greater than 100 N. b) Closing Opening length up to the automatic closing point for end pivoting beds 350 mm and for side pivoting beds 300 mm. NOTEOpening energy more than60Nm, respectively more than120Nm, is not accepted. 5 Mounting of the bed to th

34、e building The bed shall be so constructed that its mounting shall conform to the following requirements NOTEFloor-to-ceiling beds, the mounting of which cannot be pulled over because of its proximity to the ceiling, are excluded. There shall be, at least, two fixing points and there shall be, at le

35、ast, two holes for attachment in each fixing point (see also clause 6). The fastening devices and the installation instructions shall be supplied with the bed. The design of the fastening devices shall be such that no additional forces due to sagging of the floor, e.g. carpet or soft floor, up to15m

36、m, may be transmitted to fastening devices. They shall be connected to the frame by the means described in4.3 or any equivalent safety devices. The fastening shall not be capable of being released from the inside. 6 Installation instructions Each bed shall be supplied with two sets of installation i

37、nstructions. One durably and visibly attached near the fastening point. The instructions shall contain at least the following information: a) a warning against incorrect installation; b) the necessity for installation, and any further adjustment, to be carried out by competent persons only; c) the n

38、eed to check the suitability of the floor and wall and that the fastening devices supplied with the product will withstand the forces generated; d) value of the test force F Hon each attaching point; e) the number of screws required, calculated in accordance with Annex B, for each fixing point; f) t

39、he minimum and maximum weight of the mattress unless the bed is supplied with a mattress and/or has an adjustable tension system. 7 Marking All beds for which claim for conformity to this standard is made shall be marked with the following information: a) the name, registered trade name or registere

40、d trade mark of either the manufacturer, distributor or retailer; b) the number of this part of EN 1129.EN1129-1:1995 BSI 09-1999 5 Annex A (informative) Foldaway beds: Test schemeEN1129-1:1995 6 BSI 09-1999 Annex B (normative) Calculation of the minimum number of screws for fixing points The locati

41、on of the screws and the material thickness of the fitting shall be such as to ensure that the tensile force is equally distributed to all wall screws. The distance between the single wall screws shall be at least50mm. The minimum number n of screws to be used for each fixing point on the wall is ca

42、lculated by the following equation: where F H= F p 5 + 100 where NOTEThis depends on the strength of the respective wall which has to be determined individually. The maximum force on each fastening point during opening and closing procedure may be determined by calculation or measurement. Tensile lo

43、ads shall be considered positive but compressive loads shall be given zero value. F p is the maximum horizontal force on each fastening during opening and closing procedure; F H is the retaining strength of each fixing point (U 400 N); F S is the retaining force of each wall screw (resistance to dra

44、wing out). n F H F S - =7 blankBS EN 1129-1:1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated

45、by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding

46、 an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures

47、that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI poli

48、cy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.

49、Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyr