BS EN 1123-3-2004 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Dimensions and special requirements fo.pdf

《BS EN 1123-3-2004 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Dimensions and special requirements fo.pdf》由会员分享，可在线阅读，更多相关《BS EN 1123-3-2004 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Dimensions and special requirements fo.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 1123-3:2004 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems Part 3: Dimensions and special requirements for vacuum drainage systems and for drainage systems in ship-building The European Standard EN 1123

2、-3:2004 has the status of a British Standard ICS 23.040.10; 23.040.40; 23.040.60; 47.020.30 BS EN 1123-3:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 6 December 2004 BSI 6 December 2004 ISBN 0 580 44956 4 National foreword This Britis

3、h Standard is the official English language version of EN 1123-3:2004. The UK participation in its preparation was entrusted to Technical Committee ISE/8, Steel pipes, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary.

4、Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or

5、 of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text

6、; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cove

7、r, an inside front cover, the EN title page, pages 2 to 29 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN11233 November2004

8、ICS23.040.10;23.040.40;23.040.60;47.020.30 Englishversion Pipesandfittingsoflongitudinallyweldedhotdipgalvanized steelpipeswithspigotandsocketforwastewatersystems Part3:Dimensionsandspecialrequirementsforvacuum drainagesystemsandfordrainagesystemsinshipbuilding Tubesetraccordsdetube,soudslongitudina

9、lementen aciergalvanischaude,manchonenfichablepour rseauxdassainissementPartie3:Dimensionset prescriptionsparticulirespourlesrseauxdvacuation sousvideainsiquepourlesrseauxdvacuationdansla constructionnavale RohreundFormstckeauslngsnahtgeschweitem, feuerverzinktemStahlrohrmitSteckmuffefr Abwasserleit

10、ungenTeil3:Maeundspezielle AnforderungenfrUnterdruckentwsserungssysteme sowiefrEntwsserungssystemeimSchiffbau ThisEuropeanStandardwasapprovedbyCENon23September2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofana

11、tionalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undert

12、heresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembo

13、urg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansr

14、eserved worldwideforCENnationalMembers. Ref.No.EN11233:2004:EEN 1123-3:2004 (E) 2 Contents Page Foreword .3 Introduction.4 1 Scope4 2 Normative references.4 3 Terms and definitions 5 4 Symbols and abbreviations .5 5 Pipes and fittings requirements.6 5.1 General6 5.2 Operating pressure, operating tem

15、perature and tightness 7 6 Dimensions.7 6.1 General and tolerances7 6.2 Sockets .7 6.2.1 Sockets for gravity drainage systems.7 6.2.2 Sockets for vacuum operation (vacuum system) .8 6.3 Pipes .9 6.3.1 Pipes for gravity drainage systems (gravity systems) .9 6.3.2 Pipes for vacuum operation (vacuum sy

16、stems) .9 6.4 Fittings10 6.4.1 Fittings for gravity systems .10 6.4.2 Flange connecting pieces19 6.4.3 Fittings for vacuum systems .20 6.4.4 Other fittings.24 7 Seals .25 7.1 General25 7.2 Seal for DN 40 to DN 70 for socket shape 1 V and 3 V for vacuum operation shape M 4.25 7.3 Seal for DN 40 to DN

17、 70 for vacuum and overpressure operation for socket shapes 1A, 2A, and 3A shape M 5 26 7.4 Seal for DN 40 to DN 150 for operation at higher pressures for socket shape 1A shape M 6.27 8 Testing 28 9 Assessment of conformity.28 Bibliography29 EN 1123-3:2004 (E) 3 Foreword This document (EN 1123-3:200

18、4) has been prepared by Technical Committee CEN/TC 165 “Waste water engineering”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2005, and conflicting

19、 national standards shall be withdrawn at the latest by May 2005. This document on pipes and fittings of longitudinally welded hot-dip galvanized steel pipe with spigot and socket for waste water systems consists of the following Parts: Part 1: Requirements, testing, quality control; Part 2: Dimensi

20、ons Part 3: Dimensions and special requirements for vacuum drainage systems and for drainage systems in shipbuilding According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyp

21、rus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United KingdomEN 1123-3:2004 (E) 4 Introduction Pipes and fit

22、tings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems as specified in EN 1123-2 are used in gravity drainage systems in buildings. For vacuum drainage systems and for drainage systems in shipbuilding, it was necessary to specify additional requi

23、rements and further dimensional specifications for components and joints used in these systems. Components specified in this document are used for vacuum drainage systems and for drainage systems in shipbuilding. 1 Scope This document specifies requirements, dimensions and tolerances for pipes and f

24、ittings of longitudinally welded, hot-dip galvanized steel pipe with spigot and socket used for vacuum drainage systems inside and outside buildings and for gravity and vacuum drainage systems on ships and floating maritime structures 1) : above freeboard deck as long as the heeling is taken into ac

25、count in the event of damage when installed above freeboard deck on passenger ships; inside a watertight compartment below freeboard deck; with direct connection to the outboard (not permitted below freeboard deck); inside tanks as long as these are not filled with foreign media and are not cargo ta

26、nks. On well-anchored maritime structures, this standard applies to pipes and fittings of longitudinally welded hot- dip galvanized steel pipe with spigot and socket used in drainage systems in the living area. NOTE Pipes and fittings according to this document may also be used in central vacuum cle

27、aning installations, in vacuum suction lifting installations, in chip transporting installations and in other waste water and process pipes as long as the media to be discharged do not damage the components or the health and safety of the personnel. For other pipes, this document only applies if agr

28、eed with the relevant operators and following prior consultation with the manufacturer. This document contains a designation system for the different types of pipes and fittings for easy identification of each component. This document is only applicable in conjunction with EN 1123-1. It does not app

29、ly to the marking of products for which EN 1123-1/A1 is applicable. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced doc

30、ument (including any amendments) applies. 1)In shipbuilding, the terms “Gravity and vacuum system“ are used for this.EN 1123-3:2004 (E) 5 EN 1123-1:1999, Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 1: Requirements,

31、testing, quality control. EN 1123-2:1999, Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems Part 2: Dimensions. EN 10025, Hot rolled products of non-alloy structural steels Technical delivery conditions. EN 10226-1, Pipe threads

32、 where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads Dimensions, tolerances and designation EN 12109, Vacuum drainage systems inside buildings. ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimen

33、sions, tolerances and designation. EN ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articles Specifications and test methods (ISO 1461:1999). EN ISO 15749-2, Ships and marine technology Drainage systems on ships and marine structures Part 2: Sanitary drainage, drain piping for g

34、ravity system (ISO 15749-2:2004). EN ISO 15749-3, Ships and marine technology Drainage systems on ships and marine structures. Part 3. Sanitary drainage, drain piping for vacuum system (ISO 15749-3:2004). 3 Terms and definitions For the purposes of this document, the terms and definitions given in E

35、N 1123-1:1999 apply. 4 Symbols and abbreviations DN/ID nominal size with regard to the inside diameter DN/OD nominal size with regard to the outside diameter d diameter t socket depth s wall thickness s 2 wall thickness of weld-in sleeve l effective length r radius angle m 10thread dimension k diame

36、ter of row of holes EN 1123-3:2004 (E) 6 5 Pipes and fittings requirements 5.1 General Components covered by this document shall meet the requirements of EN 1123-1 They shall have a suitable corrosion protection coating as specified in EN ISO 1461 for use in drainage systems for the discharge of bla

37、ck water, gray water and waste water from process pipe systems. For weld-in sleeves and flanges, weldable material, e.g. S235 JRG2 as specified in EN 10025 or the specifications of the classification societies valid at the place of use of the product shall be used The suitability of these pipes and

38、fittings for other media shall be agreed with the manufacturer. EN 1123-3:2004 (E) 7 5.2 Operating pressure, operating temperature and tightness The components shall be dimensioned so that they are reliably tight under the operating conditions given in Table 1 with the indicated type of socket and d

39、esign being used. Table 1 Type of socket joint according to operating data for the pipe system Socket joint Pipe system for Operating pressure Operating temperature Seal aType Socket shape b Deck drainage Sanitary drain line in gravity system up to 0,5 bar M 1, M 2, M 3, M 5 inserted 1 A, 2 A, 3 A -

40、 0,3 bar to 0,6 bar (corresponding to 0,7 bar to 0,4 bar absolute pressure) M 1 inserted and bonded 1 A, 2 A, 3 A M 5 inserted 1 A, 2 A, 3 A Sanitary drain line in vacuum system up to 0,8 bar (corresponding to 0,2 bar absolute pressure) Up to 90 C in cyclical duty c M 4 inserted 1 V or 3 V Vent line

41、 Following agreement with the relevant supervisory bodies and discussion with the manufacturer. M 1, M 6 inserted and bonded with shear protection 1 A, 2 A, 3 A aRequirements as specified in clause 7 bSocket shapes A according to EN 1123-2; socket shape V according to 6.2 cFor higher temperatures, t

42、he manufacturer is to be consulted. 6 Dimensions 6.1 General and tolerances The figures in this document are simplified drawings. The dimensions given shall be followed. Where no tolerances are given in this document, the requirements of EN 1123-2 shall be met. 6.2 Sockets 6.2.1 Sockets for gravity

43、drainage systems The socket shapes and socket dimensions shall conform to type A of EN 1123-2. If the designation of the fittings does not specify the socket shape, they are of socket shape 1 A. Dimensions not specified shall be chosen accordingly. EN 1123-3:2004 (E) 8 6.2.2 Sockets for vacuum opera

44、tion (vacuum system) The socket shapes and socket dimensions shall conform to shape A as specified in EN 1123-2 in conjunction with seals of shape M 1 and M 5 or the socket shape shown in Figure 1 and the socket dimensions in Table 2. If the designation of the fittings does not specify the socket sh

45、ape, they are of shape 1 A and 1 V. Dimensions not specified shall be selected accordingly. Socket shape 1 V Socket shape3 V Vacuum socket Long vacuum socket Figure 1 Socket shapes Table 2 Socket dimensions Dimensions in millimetres Socket dimensions Nominal size DN/ID d 1 a sb D 2d 3Tolerances for

46、d 1to d 3 t 1t 2Tolerances for t 1and t 240 42 1,5 0,15 45 50 0,6 70 2 4 +50 53 1,5 0,15 56 62 0,6 90 2 4 +70 73 1,6 0,16 76 84,5 0,7 120 2 4 +aPipe ends slightly retracted.b The indications on wall thickness refer to the ungalvanized pipe.EN 1123-3:2004 (E) 9 6.3 Pipes 6.3.1 Pipes for gravity drain

47、age systems (gravity systems) For gravity systems conforming to EN ISO 157492, pipes as specified in EN 1123-2 shall be used. 6.3.2 Pipes for vacuum operation (vacuum systems) 6.3.2.1 General For vacuum systems for building drainage or in ships and marine structures as specified in EN ISO 15749-3, p

48、ipes conforming to EN 1123-2 with socket shapes 1 A, 2 A or 3 A with seals of shapes M 1 and M 5 or pipes of shapes B 1 and B 2 as shown in Table 3 shall be used. For sockets of shape 1 V or 3 V as shown in Figure 2, the seals shall be of shape M 4. The effective length of the pipes shall be as shown in Table 3. If pipes are provided with additional corrosion protection (P) according to clause 9 of EN 1123-1:1999, this shall b