BS EN 1053-1996 Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test methods for watertightness《塑料管道系统 无压力情况下使用的热塑管道系统 水密性试验方法》.pdf

《BS EN 1053-1996 Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test methods for watertightness《塑料管道系统 无压力情况下使用的热塑管道系统 水密性试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1053-1996 Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test methods for watertightness《塑料管道系统 无压力情况下使用的热塑管道系统 水密性试验方法》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1053 : 1996 BS 2782

2、 : Part 11 : Method 1112B : 1996 The European Standard EN 1053 : 1995 has the status of a British Standard ICS 23.040.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Plastics piping systems Thermoplastics piping systems for non-pressure applications Test method for watertig

3、htnessThis British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 August 1996 BSI 1996 The following BSI references relate to the work on this standard: Committee

4、 reference PRI/61 Draft for comment 92/52897 DC ISBN 0 580 25545 X BS EN 1053 : 1996 Amendments issued since publication Amd. No. Date Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee PRI/61, Plastics piping

5、systems and components, upon which the following bodies were represented: British Gas plc British Plastics Federation British Plumbing Fittings Manufacturers Association British Valve and Actuator Manufacturers Association Department of the Environment (British Board of Agre ment) Department of the

6、Environment (Building Research Establishment) Department of the Environment (Property and Buildings Directorate) Department of Transport Electricity Association Federation of Civil Engineering Contractors Health and Safety Executive Institute of Building Control Institute of Materials Institution of

7、 Civil Engineers Institution of Gas Engineers Institution of Water and Environmental Management National Association of Plumbing, Heating and Mechanical Services Contractors Pipeline Industries Guild Plastics Land Drainage Manufacturers Association Society of British Gas Industries Society of Britis

8、h Water Industries Water Companies Association Water Services Association of England and Wales The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Engineering Equipment and Materials Users Association ERA Technology Ltd. RAPRA Technology Ltd.

9、BS EN 1053 : 1996 BSI 1996 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Method 1 Scope 3 2 Principle 3 3 Apparatus 3 4 Test pieces 3 5 Procedure 3 6 Test report 3 Figure 1 Typical arrangement 4ii BSI 1996 BS EN 1053 : 1996 National foreword This British S

10、tandard has been prepared by Technical Committee PRI/61 and is the English language version of EN 1053 : 1995 Plastics piping systems Thermoplastics piping systems for non-pressure applications Test method for watertightness, published by the European Committee for Standardization (CEN). It is incor

11、porated into BS 2782 Methods of testing plastics: Part 11: Thermoplastics pipes, fittings and valves, as Method 1112B : 1996 for association with related test methods for plastics materials and plastics piping components. This test method has been prepared for reference by other standards under prep

12、aration by CEN for specification of plastics piping systems and components. It has been implemented to enable experience of the Method to be gained and for use for other fresh applications. It is also for use for the revision or amendment of other national standards as practicable, but it should not

13、 be presumed to apply to any existing standard or specification which contains or makes reference to a different test method until that standard/specification has been amended or revised to make reference to this Method. This Method supersedes BS 2782 : Part 11 : Method 1112A : 1989, which becomes o

14、bsolescent except for supporting references thereto in BS 4576 : Part 1 : 1989, BS 4660 : 1989 and BS 5255 : 1989. The principal technical differences between EN 1053 : 1995 and BS 2782 : Part 11 : Method 1112A : 1989 are as follows. Parameter EN 1053 : 1995 BS 2782 : Part 11 : Method 1112A : 1989 a

15、) Ambient temperature during test piece assembly and testing (23 5) C 15 C to 35 C b) Angular deflection applied to the joint under test Yes, if deflection is possible, to maximum declared for the joint by its manufacturer Not specifically required, unless specified by the product specification c) P

16、eriod for raising the pressure to the test pressure of$ 0,5 bar smoothly over not greater than 15 min Not specified d) Period for which a test pressure of$ 0,5 bar is maintained at least 15 min not less than 60 s e) Inspection for and report of any change in appearance (other than leakage) Yes Not c

17、alled for Warning note. This British Standard, which implements EN 1053 : 1995, does not necessarily detail all the precautions necessary to meet the requirements of the Health and Safety at Work etc. Act 1974. Attention should be paid to any appropriate safety precautions and the test method should

18、 be operated only by trained personnel. Compliance with a British Standard does not of itself confer immunity from legal obligations.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussel

19、s 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN 1053 : 1995 E EUROPEAN STANDARD EN 1053 NORME EUROPE ENNE EUROPA ISCHE NORM October 1995 ICS 23.040.20 Descriptors: Sanitation, water removal, sewage, buildi

20、ngs, interior, plastic tubes, thermoplastic resins, leak tests, water-tightness verification English version Plastics piping systems Thermoplastics piping systems for non-pressure applications Test method for watertightness Syste mes de canalisations en plastiques Syste mes de canalisations thermopl

21、astiques pour applications sans pression Me thode dessai de le tanche ite a leau Kunststoff-Rohrleitungssysteme Rohrleitungssysteme aus Thermoplasten fu r drucklose Anwendungen Pru fverfahren auf die Wasserdichtheit This European Standard was approved by CEN on 1995-10-05. CEN members are bound to c

22、omply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central

23、Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the

24、official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 1053 : 1995 BSI 1996 Foreword This European Sta

25、ndard has been prepared by the Technical Committee CEN/TC 155, Plastics piping systems and ducting systems, of which the secretariat is held by NNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by

26、 April 1996, and conflicting national standards shall be withdrawn at the latest by April 1996. According to CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,

27、Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This standard is based on annex B Watertightness test of ISO 3633 : 1991 Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings for soil and waste discharge (low and high temperature) systems inside

28、buildings Specifications, published by the International Organization for Standardization (ISO). It is a modification of annex B for reasons of applicability to other plastics materials and/or other test conditions and alignment with texts of other standards on test methods. The modifications are: n

29、o material is mentioned; test parameters, except those common to all plastics, are omitted; no diameter limit is included; no material-dependent requirements are given; editorial changes have been introduced; the method has been extended to cover quick testing of fabricated products made from more t

30、han one piece. The material-dependent test parameters and/or performance requirements are incorporated in the system standard(s) concerned. This standard is one of a series of standards on test methods which support system standards for plastics piping systems and ducting systems.Page 3 EN 1053 : 19

31、95 BSI 1996 1 Scope This standard specifies a test method for watertightness of: a) joints of thermoplastics piping systems for non-pressure applications; b) thermoplastics fabricated products made from more than one piece for non-pressure applications. 2 Principle A test assembly comprising either

32、a fabricated product or an assembly of pipes and/or fittings is subjected to a given internal hydrostatic pressure for a given period during which the leaktightness of the fabricated product or the joint is verified by inspection. NOTE. It is assumed that the following test parameters are set by the

33、 standard making reference to this standard: a) the sampling procedure (see 4.1); b) the number of test pieces (see 4.2). 3 Apparatus 3.1 End-sealing devices, having a size and using a sealing method both appropriate to the type of joint under test. The devices shall be restrained in a manner that d

34、oes not exert longitudinal forces on the joint assembly and that prevents the devices or the assembly under test from separating under pressure. The weight of the devices shall not be allowed to influence the angular deflection to be applied (see 5.2). 3.2 Hydrostatic pressure source, connected to o

35、ne end of at least one end-sealing device, capable of applying the required pressure gradually and evenly in accordance with 5.4 and then of keeping it constant to within % for the duration of the test required 21 +2 (see clause 5). 3.3 Bleed valve, capable of venting air when hydrostatic pressure i

36、s applied to the test piece. 3.4 Pressure measuring device, capable of checking conformity to the required test pressure (see 3.2 and clause 5). 4 Test pieces 4.1 Preparation The test piece shall comprise either a fabricated fitting or an assembly of (a) pipe section(s) (with or without sockets) and

37、/or fitting(s) including at least one joint of the type under test (see figure 1). To assist air removal, the test piece may be inclined by up to 12. The assembly of the joint(s) shall be carried out in accordance with the manufacturers instructions. The assembly shall comprise the combination of th

38、e smallest available spigot end and the largest available socket or socket groove diameter within the applicable tolerance(s) and obtained by sampling in accordance with the referring standard. The relevant diameters of the selected spigot(s) and socket(s) shall be measured and recorded. 4.2 Number

39、The number of test pieces shall be as specified in the referring standard. 5 Procedure 5.1 Carry out the following procedure at an ambient temperature of (23 5) C using cold tap water without permitting any condensation on the surface of the test piece. 5.2 Mount the test piece in the apparatus. If

40、the joint to be tested permits angular deflection, arrange the test assembly so that the joint(s) under test is (are) subject to the (their) maximum angular deflection, as declared for the joint by the manufacturer, for the axes of the components thus joined. 5.3 When testing in accordance with 5.4

41、and 5.5, monitor the test piece for and record any evidence of leakage. 5.4 Introduce water into the test piece, while bleeding off all air, and apply the hydrostatic pressure as follows: a) accelerated procedure for fabricated products: unless otherwise specified in the referring standard, apply an

42、 hydrostatic pressure of 0,5 bar (50 kPa) and maintain it for at least 1 min. b) assemblies of pipes and/or fittings which are not fabricated: raise the hydrostatic pressure smoothly over a period of not greater than 15 min to 0,5 bar (50 kPa) and maintain that pressure for at least 15 min. 5.5 Depr

43、essurize, drain and dismantle the test piece. Inspect for and record any changes in the appearance of the components tested. 6 Test report The test report shall include the following information: a) a reference to this standard and to the referring standard; b) the identification of the components (

44、e.g. fitting(s), pipe(s), seal(s) comprising the joint(s) under test and their respective diameters, in millimetres (see 4.1); c) the ambient temperature (see 5.1), in degrees Celsius; d) the test pressure, in bars; e) the length of time under pressure, in minutes; f) if applicable, the angle of def

45、lection applied to the joint (see 5.2); g) a statement, that the joint did not leak or, if any, a report of signs of leakage or rupture, their position(s) and the pressure at which they occurred; h) any changes in the appearance of the components of the test piece(s) during the test, or immediately

46、afterwards; i) any factors which may have affected the results, for example, such as any incidents or any operating details not specified in this standard; j) the date of the test.Page 4 EN 1053 : 1995 BSI 1996 Dimensions in metres A Air outlet B Water inlet C Sealing plug with water inlet, air outl

47、et and end restraint D Water outlet E Sealing plug with water outlet and end restraint (see 3.1) F Direction of movement for angular deflection, if applicable (see 5.2) G Loose bushes to allow all sizes of pipes to be accommodated on the same test fixture H Fixed points J Fixed component Figure 1. T

48、ypical arrangementblankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

49、| | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services.