BS EN 10021-2006 General technical delivery requirements for steel products《钢制品的一般技术交货要求》.pdf

《BS EN 10021-2006 General technical delivery requirements for steel products《钢制品的一般技术交货要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10021-2006 General technical delivery requirements for steel products《钢制品的一般技术交货要求》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 10021:2006General technical delivery conditions for steel productsThe European Standard EN 10021:2006 has the status of a British StandardICS 77.140.01g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g5

2、1g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Mon Sep 10 00:53:47 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 10021:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2007 BS

3、I 2007ISBN 978 0 580 50077 0National forewordThis British Standard was published by BSI. It is the UK implementation of EN 10021:2006. It supersedes BS EN 10021:1993 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/5, Technical delivery conditions,

4、classification and designation of steels.A list of organizations represented on ISE/5 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Stand

5、ard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Mon Sep 10 00:53:47 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10021December 2006ICS 77.140.01 Supersedes EN 10021:

6、1993 English VersionGeneral technical delivery conditions for steel productsConditions gnrales techniques de livraison des produitsen acierAllgemeine technische Lieferbedingungen frStahlerzeugnisseThis European Standard was approved by CEN on 25 November 2006.CEN members are bound to comply with the

7、 CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or t

8、o any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.C

9、EN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switz

10、erland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1

11、0021:2006: ELicensed Copy: Wang Bin, na, Mon Sep 10 00:53:47 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 10021:2006 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Information to be supplied by the purchaser .6 5 Manufacturing process .6 6 Supply by an

12、intermediary6 7 Requirements.7 7.1 General7 7.2 Chemical composition 7 7.3 Mechanical properties.7 7.4 Surface and internal quality7 7.4.1 General7 7.4.2 Detection of discontinuities7 7.4.3 Removal of discontinuities .7 7.4.4 Repairs by welding 8 8 Inspection .8 8.1 Type of inspection documents and

13、type of inspection .8 8.2 Non-specific inspection 8 8.3 Specific inspection 8 8.3.1 General8 8.3.2 Testing frequency9 8.3.3 Sampling conditions and test pieces 9 8.3.4 Test procedures.10 8.4 Invalidation of test results 11 8.5 Rounding of results of mechanical and chemical tests 11 9 Sorting and rep

14、rocessing .11 10 Marking .12 11 Disputes12 Bibliography 17 Licensed Copy: Wang Bin, na, Mon Sep 10 00:53:47 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 10021:2006 (E) 3 Foreword This document (EN 10021:2006) has been prepared by Technical Committee ECISS/TC 9 “Technical conditions of delivery and q

15、uality control”, the secretariat of which is held by IBN/BIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June

16、 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lat

17、via, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, na, Mon Sep 10 00:53:47 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 10021:2006 (E) 4 1 Scope This European Standard specifie

18、s the general technical delivery conditions for all steel products covered by EN 10079 with the exception of steel castings and powder metallurgical products. Where the delivery requirements agreed for the order or specified in the appropriate product specification differ from the general technical

19、delivery conditions defined in this European Standard, then the requirements agreed for the order or specified in the appropriate product specification apply. NOTE Inspection documents are covered by EN 10168 and EN 10204. 2 Normative references The following referenced documents are indispensable f

20、or the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. CR 10261, ECISS Information Circular 11 Iron and steel Review of available methods of chemical analysis

21、 EN 10020:2000, Definition and classification of grades of steel EN 10052:1993, Vocabulary of heat treatment terms for ferrous products EN 10079:1992, Definition of steel products EN 10204:2004, Metallic products Types of inspection documents EN ISO 377, Steel and steel products Location and prepara

22、tion of samples and test pieces for mechanical testing (ISO 377:1997) ISO 31-0:1992, Quantities and units Part 0: General principles 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10020:2000, EN 10052:1993, EN 10079:1992, EN 10204:2004 and the follow

23、ing apply. 3.1 cast (heat) analysis chemical analysis representative of the cast (heat) determined by the steelmaker at his discretion in a manner of his choice 3.2 inspection conformity evaluation by observation and judgment accompanied as appropriate by measurement, testing or gauging 3.3 inspecti

24、on representative(s) one or more individual(s) who is/are either: a) the inspector(s) designated in any official regulation; b) the manufacturers authorized inspection representative(s), independent from the manufacturing department; c) the purchasers authorized inspection representative(s) Licensed

25、 Copy: Wang Bin, na, Mon Sep 10 00:53:47 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 10021:2006 (E) 5 NOTE 1 The inspection representatives mentioned in a) and c) are referred to in the text as external inspection representatives. NOTE 2 The inspection representatives validate the inspection and te

26、st results. Inspection and testing can also be carried out by the manufacturing department. 3.4 non-specific inspection inspection carried out by the manufacturer in accordance with his own procedures to assess whether products defined by the same product specification and made by the same manufactu

27、ring process are in compliance with the requirements of the order or not NOTE The products inspected may not necessarily be the products actually supplied. 3.5 product analysis chemical analysis carried out on a sample of the product 3.6 rough specimen part of the sample having undergone forming and

28、/or machining, followed by heat treatment where appropriate, for the purpose of producing test pieces (see Figure 1) 3.7 sample sufficient quantity of material taken from the sample product for the purposes of producing one or more test pieces (see Figure 1) NOTE In certain cases, the sample can be

29、the sample product itself or the rough specimen. 3.8 sample product item (a sheet, for example) selected from a test unit for the purpose of obtaining test pieces (see Figure 1) NOTE In certain cases the sample product can be the sample itself. 3.9 sequential testing group or series of tests from wh

30、ich the average and individual results are used to demonstrate that the requirements of the order and/or product specification have been satisfied 3.10 specific inspection inspection carried out, before delivery, according to the product specification on the products to be supplied or on test units

31、of which the products supplied are part, in order to verify that these products are in compliance with the requirements of the order 3.11 testing determination of one or more characteristics according to a procedure 3.12 test piece part of the sample, with specified dimensions, machined or un-machin

32、ed, brought to a required condition for submission to a given test (see Figure 1) NOTE In certain cases, the test piece can be the sample itself or the rough specimen. Licensed Copy: Wang Bin, na, Mon Sep 10 00:53:47 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 10021:2006 (E) 6 3.13 test unit number

33、 of pieces or mass of products to be accepted or rejected together, on the basis of the tests to be carried out on sample products in accordance with the requirements of the product specification or order (see Figure 1) 4 Information to be supplied by the purchaser 4.1 The purchaser shall select the

34、 steel grade, the shape of the product and the dimensions, taking the intended processing and use into account. He may take the manufacturers advice in making his choice. The order shall provide all the information necessary for describing the required product and its characteristics and details con

35、cerning delivery, e.g.: a) mass, length, area, number of pieces; b) the product form (it may be a drawing number for example); c) the nominal/specified dimensions; d) the tolerances on the characteristics in a), b) and c); e) the steel designation; f) the delivery conditions (type of heat treatment,

36、 surface treatment etc.); g) the specific requirements for surface and/or internal quality (see 7.4); h) the type of inspection document (see EN 10204) if required; i) the inspection requirements when not specified in the product specification (see Clause 8); j) the requirements for marking, packing

37、 and loading; k) any optional (supplementary) requirements provided for by the specification to apply. 4.2 The information in 4.1 shall be specified either by reference to one or more standards or, in the absence of a standard, by stipulation of the required characteristics and conditions. If, in an

38、 order, reference is made to a given standard without specifying its edition date, this reference shall be interpreted as being the latest edition at the date of the order acknowledgment. 5 Manufacturing process The manufacturing process shall be left to the discretion of the manufacturer unless oth

39、erwise agreed at the time of enquiry and order or otherwise specified in the product specification. NOTE The manufacturing process covers all operations up to the delivery of the product. 6 Supply by an intermediary When a product is supplied by an intermediary, he shall submit to the purchaser, wit

40、hout any changes to it, the manufacturers documentation. This documentation from the manufacturer shall be accompanied by suitable means of identification of the product, in order to ensure the traceability between the product and the documentation (see Clause 10). Licensed Copy: Wang Bin, na, Mon S

41、ep 10 00:53:47 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 10021:2006 (E) 7 If the intermediary has changed the dimensions of the product, he shall supply an additional document of compliance for these particular new conditions. This also applies to all special requirements given in the order and n

42、ot defined in the manufacturers documentation. NOTE Any organization which during processing changes the metallurgical state of the product is considered as a product or material manufacturer. 7 Requirements 7.1 General The products shall comply with the requirements of the order. Consequently, the

43、manufacturer shall carry out appropriate process control and inspection to ensure that the delivery complies with the requirements of the order, irrespective of the type of inspection document required (see Clause 8). NOTE Examples for quality management systems can be found in appropriate documents

44、, e.g. EN ISO 9001. 7.2 Chemical composition Requirements concerning the chemical composition shall be considered to refer to the cast (heat) analysis unless they refer expressly to the product analysis. 7.3 Mechanical properties 7.3.1 Where, in the product specification, the mechanical properties a

45、re specified by dimensional categories e.g. based on thickness or diameter, the dimension to be considered is the nominal/specified dimension of the product at the prescribed location for taking samples for mechanical tests. 7.3.2 In the absence of any specification in the order or the product speci

46、fication, the mechanical properties relate to the as-delivered condition of the products. 7.3.3 Where an impact energy value is specified, without any further information, it shall be interpreted as representing the average value of those individual tests which shall be assessed as described in 8.3.

47、4.2. 7.4 Surface and internal quality 7.4.1 General All products shall have a finish appropriate to the manufacturing route. Minor surface and internal discontinuities which may occur under normal manufacturing conditions shall not be a basis for rejection. Detailed requirements referring to the sur

48、face and internal quality shall, where appropriate, be agreed at the time of enquiry and order, by reference to the appropriate European Standard or other relevant standard if no European Standard exists. 7.4.2 Detection of discontinuities When special techniques (radiography, ultrasonics, magnetic

49、detection etc.) are required to detect discontinuities, they shall, as well as the test frequency and the acceptance criteria, be as specified in the product specification or as agreed at the time of enquiry and order. 7.4.3 Removal of discontinuities Surface discontinuities may be removed by appropriate means provided that the dimensions and properties of the product remain within the limits specified in either the order, product specification, dimensional standard or surface quality standard. Licensed Copy: Wang Bin, na, Mon Sep 10 00:53:47 GMT+00:00 2007, Uncon