BS DD CEN TS 81-11-2011 Safety rules for the construction and installation of lifts Basics and interpretations Interpretations related to EN 81 family of standards《电梯建造和安装的安全规则 基础和.pdf

《BS DD CEN TS 81-11-2011 Safety rules for the construction and installation of lifts Basics and interpretations Interpretations related to EN 81 family of standards《电梯建造和安装的安全规则 基础和.pdf》由会员分享，可在线阅读，更多相关《BS DD CEN TS 81-11-2011 Safety rules for the construction and installation of lifts Basics and interpretations Interpretations related to EN 81 family of standards《电梯建造和安装的安全规则 基础和.pdf（164页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationDD CEN/TS 81-11:2011Safety rules for theconstruction and installationof lifts Basics andinterpretationsPart 11: Interpretations related to EN 81family of standardsDD CEN/TS 81-11

2、:2011 DRAFT FOR DEVELOPMENTNational forewordThis Draft for Development is the UK implementation of CEN/TS81-11:2011. It supersedes DD CEN/TS 81-11:2009 which is withdrawn.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publicatio

3、nsand is of a provisional nature. It should be applied on thisprovisional basis, so that information and experience of its practicalapplication can be obtained.Comments arising from the use of this Draft for Developmentare requested so that UK experience can be reported to theinternational organizat

4、ion responsible for its conversion toan international standard. A review of this publication willbe initiated not later than 3 years after its publication by theinternational organization so that a decision can be taken on itsstatus. Notification of the start of the review period will be made inan a

5、nnouncement in the appropriate issue of Update Standards.According to the replies received by the end of the review period,the responsible BSI Committee will decide whether to support theconversion into an international Standard, to extend the life of theTechnical Specification or to withdraw it. Co

6、mments should be sentto the Secretary of the responsible BSI Technical Committee at BritishStandards House, 389 Chiswick High Road, London W4 4AL.The UK participation in its preparation was entrusted to TechnicalCommittee MHE/4, Lifts, hoists and escalators.A list of organizations represented on thi

7、s committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 71861 8ICS 91.140.90Compliance with a British Standard cannot confer immunity fromle

8、gal obligations.This Draft for Development was published under the authority ofthe Standards Policy and Strategy Committee on 30 April 2011.Amendments issued since publicationDate Text affectedDD CEN/TS 81-11:2011TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 81-11 Ma

9、rch 2011 ICS 91.140.90 Supersedes CEN/TS 81-11:2009English Version Safety rules for the construction and installation of lifts - Basics and interpretations - Part 11: Interpretations related to EN 81 family of standards Rgles de scurit pour la construction et linstallation des lvateurs - Fondamentau

10、x et interprtations - Partie 11: Interprtations relatives aux normes de la famille EN 81 Sicherheitsregeln fr die Konstruktion und den Einbau von Aufzgen - Grundlagen und Auslegungen - Teil 11: Auslegungen zur Normenreihe EN 81 This Technical Specification (CEN/TS) was approved by CEN on 3 January 2

11、011 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are requir

12、ed to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conve

13、rsion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Po

14、land, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by

15、 any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 81-11:2011: EDD CEN/TS 81-11:2011CEN/TS 81-11:2011 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 List of interpretations 63.1 Interpretations pertaining to EN 81-1:1998 and EN 81-2:1998 63.2 Int

16、erpretations pertaining to EN 81-28:2003 163.3 Interpretations pertaining to EN 81-58:2003 163.4 Interpretations pertaining to EN 81-70:2003 163.5 Interpretations pertaining to EN 81-72:2003 173.6 Interpretations pertaining to EN 81-73:2005 194 Interpretations . 204.1 For EN 81-1 and EN 81-2 204.2 F

17、or EN 81-28 204.3 For EN 81-58 204.4 For EN 81-70 204.5 For EN 81-72 204.6 For EN 81-73 20Section 4.1 - Interpretations related to EN 81-1 and EN 81-2 21Section 4.2 - Interpretations related to EN 81-28 117Section 4.3 - Interpretations related to EN 81-58 119Section 4.4 - Interpretations related to

18、EN 81-70 121Section 4.5 - Interpretations related to EN 81-72 133Section 4.6 - Interpretations related to EN 81-73 149Annex A (normative) List of interpretations pertaining to previous editions of EN 81-1 and EN 81-2 still valid for EN 81-1/2:1998 . 151Bibliography . 159DD CEN/TS 81-11:2011CEN/TS 81

19、-11:2011 (E) 3 Foreword This document (CEN/TS 81-11:2011) has been prepared by Technical Committee CEN/TC 10 “Lifts, escalators and moving walks”, the secretariat of which is held by AFNOR. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

20、rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 81-11:2009. This document is a collection of interpretations related to the EN 81 family of standards. For the time being this collection of interpretations relates

21、 to the following standards: EN 81-1, EN 81-2, EN 81-28, EN 81-58, EN 81-70, EN 81-72 and EN 81-73. According to the progress in working out interpretations, this document will be amended and/or completed. This is the second edition of this CEN Technical Specification. It replaces the former CEN/TS

22、81-11:2009. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,

23、 Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DD CEN/TS 81-11:2011CEN/TS 81-11:2011 (E) 4 Introduction Standards reflect the consensus of the best European experti

24、se and are prepared with highest care. Product standards cannot be formulated in such a way that they describe all possible technical solutions and therefore exclude all uncertainties regarding the understanding of the required provisions. On the other hand technology is in a permanent evolution, th

25、e progress of which cannot be incorporated into standards quickly enough. Interpretations are a practical way to give: a) answers to questions regarding the understanding of clauses in standards; b) feedback to the CEN-Committee responsible for a standard about the practical experiences resulting fr

26、om the use of the standard; c) guidance to further development and improvement of standards following: 1) experience, especially accidents and incidents; 2) progress in technology; 3) state of the art. Information concerning the procedure developed by CEN/TC 10 concerning the elaboration of interpre

27、tations is shown in CEN/TR 81-10. DD CEN/TS 81-11:2011CEN/TS 81-11:2011 (E) 5 1 Scope This Technical Specification is a collection of interpretations related to the EN 81 family of standards (see CEN/TR 81-10:2008). As second issue, this document collects interpretations to EN 81-1:1998, EN 81-2:199

28、8, EN 81-28:2003, EN 81-58:2003, EN 81-70:2003, EN 81-72:2003 and EN 81-73:2005. Interpretations to other standards of the EN 81 family will be added when they are available. Interpretations aim to improve the understanding of the clause(s) they are referring to and by that facilitating common under

29、standing between manufacturers, lift installers, notified bodies, inspection bodies and national authorities. Interpretations do not have the same status as the standards to which they are related. However, the application of interpretations should give to the interested parties confidence that the

30、relevant standard has not been wrongly applied. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

31、 amendments) applies. EN 81-1:1998, Safety rules for the construction and installation of lifts Part 1: Electric lifts EN 81-1:1998/A1:2005, Safety rules for the construction and installation of lifts Part 1: Electric lifts EN 81-1:1998/A2:2004, Safety rules for the construction and installation of

32、lifts Part 1: Electric lifts A2: Machinery and pulley spaces EN 81-2:1998, Safety rules for the construction and installation of lifts Part 2: Hydraulic lifts EN 81-2:1998/A1:2005, Safety rules for the construction and installation of lifts Part 2: Hydraulic lifts EN 81-2:1998/A2:2004, Safety rules

33、for the construction and installation of lifts Part 2: Hydraulic lifts A2: Machinery and pulley spaces EN 81-28:2003, Safety rules for the construction and installation of lifts Lifts for the transport of persons and goods Part 28: Remote alarm on passenger and goods passenger lifts EN 81-58:2003, S

34、afety rules for the construction and installation of lifts Examination and tests Part 58: Landing doors fire resistance test EN 81-70:2003, Safety rules for the construction and installations of lifts Particular applications for passenger and good passengers lifts Part 70: Accessibility to lifts for

35、 persons including persons with disability EN 81-70:2003/A1:2004, Safety rules for the construction and installations of lifts Particular applications for passenger and goods passengers lifts Part 70: Accessibility to lifts for persons including persons with disability EN 81-72:2003, Safety rules fo

36、r the construction and installation of lifts Particular applications for passenger and goods passenger lifts Part 72: Firefighters lifts EN 81-73:2005, Safety rules for the construction and installation of lifts Particular applications for passenger and goods passenger lifts Part 73: Behaviour of li

37、fts in the event of fire DD CEN/TS 81-11:2011CEN/TS 81-11:2011 (E) 6 3 List of interpretations The following lists show the valid interpretations contained in this document. 3.1 Interpretations pertaining to EN 81-1:1998 and EN 81-2:1998 This edition of CEN/TS 81-11 is updated with the following lis

38、t of interpretations (see Tables 1 and 2): 585, 586, 587, 588, 592, 593, 594 and 595. Table 1 shows the list of interpretations in their numerical order. Table 2 shows the list of interpretations in order of the clauses of EN 81-1:1998 and EN 81-2:1998 with the corresponding keywords. A number of in

39、terpretations pertaining to EN 81-1:1978, EN 81-1:1985 and EN 81-2:1987 are considered still valid for EN 81-1:1998 and EN 81-2:1998. Annex A shows the lists of these interpretations1). 1) These interpretations are available from the National CEN Member organisations or CEN/TC 10 secretariat. DD CEN

40、/TS 81-11:2011CEN/TS 81-11:2011 (E) 7 Table 1 List of interpretations in numerical order (EN 81-1 and EN 81-2) Interpretation number Related clause Date of validity Valid for (edition 1998) Key words 501 5.6.1 2001-04-15 EN 81-1/2 Protection in the well; rigid screen502 12.5.7 2001-04-15 EN 81-2 Fil

41、ters; hydraulic control and safety devices 503 J.1 (table) 2001-04-15 EN 81-1/2 Fixing of the glass panels; glass 504 J.1 (table) 2001-04-15 EN 81-1/2 Dimensions of the glass panels; glass 505 13.3.2 2001-04-15 EN 81-1/2 Door motor; overload protection 506 13.4.2 2001-04-15 EN 81-1/2 Machine-room ac

42、cesses; main switch 507 14.2.1.4 2001-04-15 EN 81-1 Emergency electrical operation; inspection operation 508 F.6 2001-04-15 EN 81-1/2 Laboratory tests; safety circuits containing electronic components 509 H.1 (table) 2001-04-15 EN 81-1/2 Electric safety circuits; printed circuits boards 510 14.1.2.1

43、.3; H.1 (table) 2001-04-15 EN 81-1/2 Electric safety circuit; gathering information 511 15 2001-04-15 EN 81-1/2 Data plate; safety device 512 10.5.3.1; 10.5.3.2 2001-04-15 EN 81-2 Final limit switch; actuation zone; creeping 513 10.5.3.1; 10.5.3.2 2001-04-15 EN 81-2 Final limit switch; actuation zon

44、e; creeping 514 14.2.3.3 2001-04-15 EN 81-1/2 Emergency alarm device; two-way voice communication Interpretation 514 is replaced by 562 515 14.1.2.1.3 2001-04-15 EN 81-1/2 Bypass of landing door and/or car door contacts 516 5.9 2002-12-31 EN 81-1/2 Illumination; lighting; well 517 5.3.2.2; 5.3.2.3 2

45、001-04-15 EN 81-1/2 Strength of the floor below the buffers 518 5.3.1.2 2001-04-15 EN 81-1/2 Glass panels; partially enclosed well; points normally accessible to persons 519 13.1.2; 14.1.2.2.2; 14.1.2.2.3; 16.2 a) 6) 2001-04-15 EN 81-1/2 Code IP; degree of protection; diagram; graphic symbol 520 9.8

46、.3.1 2001-04-15 EN 81-1 Balancing weight; counterweight; safety gear; safety rope; suspension means 521 10.3.1 2001-04-15 EN 81-1/2 Car and counterweight buffer 522 15 2001-04-15 EN 81-1/2 Electronic component; marking 523 8.2.2.4 2001-04-15 EN 81-2:1998 Goods passenger lift; maximum available car a

47、rea; rated load 524 1.3 g); 8.11.3; 8.18.1 b); 10.3.6; 10.3.7 2001-04-15 EN 81-2 Rated speed 1 m/s DD CEN/TS 81-11:2011CEN/TS 81-11:2011 (E) 8 Table 1 List of interpretations in numerical order (EN 81-1 and EN 81-2) (continued) Interpretation number Related clause Date of validity Valid for (edition

48、 1998) Key words 525 9.8.2.1 d) 2001-04-15 EN 81-2 Rated speed 0,63 m/s; safety gear 526 9.9.2.1 2001-04-15 EN 81-2 Clamping device; tripping speed 527 9.9.5.1; 9.9.5.2 2001-04-15 EN 81-2 Clamping device; release 528 D.2 n) 1) 2001-04-15 EN 81-2 Energy accumulation type buffers; test 529 J.7 2001-04

49、-15 EN 81-1/2 Exceptions to tests; pendulum shock test 530 J.7 2001-04-15 EN 81-1/2 Plain glass panel; door 531 14.2.2.2 2001-04-15 EN 81-1/2 Door; stopping device 532 1.2; 1.3 2001-04-15 EN 81-2 Maximum allowable pressure; non-toxic fluid; scope 533 10.4.3.2; 12.8 2001-04-15 EN 81-1 Reduced buffer stroke; monitoring the slowdown 534 5.10 2001-04-15 EN 81-1/2 Alarm devices; emergency release; pit 535 9.10.3 2001-04-15 EN 81-1 Ascending car; over