BS DD CEN TS 15597-2-2012 Winter maintenance equipment Spreading machines (gritting machines) Requirements for distribution and its test《冬季维护设备 涂胶机(铺砂机) 涂胶机的配置及其试验》.pdf

《BS DD CEN TS 15597-2-2012 Winter maintenance equipment Spreading machines (gritting machines) Requirements for distribution and its test《冬季维护设备 涂胶机(铺砂机) 涂胶机的配置及其试验》.pdf》由会员分享，可在线阅读，更多相关《BS DD CEN TS 15597-2-2012 Winter maintenance equipment Spreading machines (gritting machines) Requirements for distribution and its test《冬季维护设备 涂胶机(铺砂机) 涂胶机的配置及其试验》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationDD CEN/TS 15597-2:2012Winter maintenance equipment Spreading machines (gritting machines)Part 2: Requirements for distribution and its testDD CEN/TS 15597-2:2012 DRAFT FOR DEVELO

2、PMENTNational forewordThis Draft for Development is the UK implementation of CEN/TS 15597-2:2012.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisiona

3、l basis, so that information and experience of its practical application can be obtained.Comments arising from the use of this Draft for Development are requested so that UK experience can be reported to the international organization responsible for its conversion to an international standard. A re

4、view of this publication will be initiated not later than 3 years after its publication by the international organization so that a decision can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards.Accordi

5、ng to the replies received by the end of the review period, the responsible BSI Committee will decide whether to support the conversion into an international Standard, to extend the life of the T e c h n i c a l S p e c i f i c a t i o n o r t o w i t h d r a w i t . C o m m e n t s s h o u l d b e

6、s e n t to the Secretary of the responsible BSI Technical Committee at British Standards House, 389 Chiswick High Road, London W4 4AL.The UK participation in its preparation was entrusted to Technical Committee B/513, Construction equipment and plant and site safety.A list of organizations represent

7、ed on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012ISBN 978 0 580 78021 9ICS 43.160Compliance with a British

8、 Standard cannot confer immunity from legal obligations.This Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 31 January 2012.Amendments issued since publicationDate T e x t a f f e c t e dDD CEN/TS 15597-2:2012TECHNICAL SPECIFICATION SPCIFICA

9、TION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 15597-2 January 2012 ICS 43.160 English Version Winter maintenance equipment - Spreading machines (gritting machines) - Part 2: Requirements for distribution and its test Winterdienstausrstung - Streumaschinen - Teil 2: Anforderungen an die Streustoffve

10、rteilung und deren Prfung This Technical Specification (CEN/TS) was approved by CEN on 29 August 2011 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on

11、 the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting nationa

12、l standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greec

13、e, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG M

14、anagement Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 15597-2:2012: EDD CEN/TS 15597-2:2012CEN/TS 15597-2:2012 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative

15、 references 53 Terms and definitions .54 Definition of spreader type .75 Test materials .76 Certification procedure .86.1 Principle of qualification procedure 86.2 Identification and requirements on spreader types .86.3 Procedure of the static test 96.3.1 General 96.3.2 Description of static qualifi

16、cation tests per spreader type .96.3.3 Method of the static test 116.3.4 Requirements on performance 126.3.5 Development of the tests . 126.4 Dynamic test procedure . 126.4.1 Test parameters 126.4.2 Dynamic test method . 16Annex A (normative) Components having an influence on the spreading parameter

17、s . 22A.1 Type of spreader with solid thawing media . 22A.2 Type of spreader with liquid thawing media 22Bibliography . 23DD CEN/TS 15597-2:2012CEN/TS 15597-2:2012 (E) 3 Foreword This document (CEN/TS 15597-2:2012) has been prepared by Technical Committee CEN/TC 337 “Winter maintenance and road serv

18、ice area maintenance equipment”, the secretariat of which is held by AFNOR. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This Europ

19、ean standard comprises two parts: EN 15597-1, Winter maintenance equipment Spreading machines (gritting machines) Part 1: General requirements and definitions for spreading machines; CEN/TS 15597-2, Winter maintenance equipment Spreading machines (gritting machines) Part 2: Requirements for distribu

20、tion and its test. This Technical Specification was prepared with the aim of having a 3-year lifetime. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cr

21、oatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DD CEN/TS 15597-2:

22、2012CEN/TS 15597-2:2012 (E) 4 Introduction This document is meant to assess the demands made on mobile spreading machines operated in traffic. Spreading machines (spreaders/gritters) are to be operated in such way that homogeneous distribution of spreading media is given within the set spreading dos

23、age, width and spreading pattern track. Due to the different kind of thawing materials used and a lack of experience to detect the exact quantity of thawing material spread on the road, CEN/TC 337 decided to publish a Technical Specification giving the possibility to all the operators to test differ

24、ent methods to determine the precision of the spreading pattern. Therefore the test methods have not been specified in detail in this Technical Specification. But the required accuracy of the measuring methods is given. DD CEN/TS 15597-2:2012CEN/TS 15597-2:2012 (E) 5 1 Scope This Technical Specifica

25、tion gives the possibility to certify a model of vehicle-mounted or (trailer-)dragged spreading machines for winter service with standard parameters, leaving the possibility for the manufacturer to evolve performance. At the same time, information is given on the minimum content required for operati

26、ng manuals. This Technical Specification is valid for machines which are used to spread the following media: solid thawing media with or without pre-wetted media; liquid thawing media. The following points are not covered by this Technical Specification: requirements for registration and approval; r

27、equirements made by automobile manufacturers; requirements on safety these are dealt with in EN 13021. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the l

28、atest edition of the referenced document (including any amendments) applies. EN 15431, Winter and road service area maintenance equipments Power system and related controls Interchangeability and performance requirements EN 15597-1, Winter maintenance equipment Spreading machines (gritting machines)

29、 Part 1: General requirements and definitions for spreading machines 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 machine model machine model that includes a spreader of thawing material for road maintenance and its control box 3.2 spreade

30、r types spreader types as defined by using different spreading parameters according to Tables 1 and 2 3.3 test materials test materials as defined in Clause 5 3.4 test test realised with different spreading parameters (dosage, spreading width and vehicle speed), for a machine model, a test material

31、and a spreader type DD CEN/TS 15597-2:2012CEN/TS 15597-2:2012 (E) 6 3.5 qualification qualification of a machine model that states the conformity to the requirements defined in this standard NOTE The compliance with these requirements is verified by a series of static and dynamic tests defined for a

32、 type of spreader and a test material. 3.6 test report document in which the whole conditions and test results for a qualification are recorded 3.7 technical certificate technical certificate that is set for a qualified machine model NOTE If several qualifications of the same model are realised with

33、 different combinations of “test material / spreader type“, the whole test results of the different qualifications will be reported on the same technical certificate. 3.8 measurement points whole measured data in the static test, which are calculated or set according to the frequency 3.9 outer strip

34、s two strips of 1 m width which border the left and right side of a theoretical measurement area 3.10 measurement area area, in the dynamic test, corresponding to the defined spreading length multiplied by the set theoretical spreading width, and which is the effective area for collecting the spread

35、ing agent 3.11 total collecting area measurement area plus the two outer strips 3.12 effective average dosage ratio of the total mass collected on the measurement area 3.13 theoretical dosage value set on the control box in g/m23.14 theoretical total amount theoretical dosage multiplied by the measu

36、rement area 3.15 total amount complete mass collected on a measurement area 3.16 effective average dosage in a strip total amount of test material collected in this strip, divided by the strip surface area DD CEN/TS 15597-2:2012CEN/TS 15597-2:2012 (E) 7 4 Definition of spreader type Some spreaders t

37、ypes are defined by using the following range of minimum and maximum parameters: spreading width, dosage and vehicle speed ranges. The dosages and quantity given for the different test materials are defined in Clause 5 (NaCl). Table 1 Spreader types for solid thawing media Type Spreading width m Spr

38、eading dosage g/m Vehicle speed km/h Maximum quantity kg/min A 1 to 6 5 to 30 5 to 40 120 B 2 to 8 5 to 30 5 to 60 240 C 3 to 12 5 to 30 5 to 80 300 Table 2 Spreader type for liquid thawing media Type Spreading width m Width step m Spreading dosageg/m Vehicle speed km/h Maximum quantity kg/min A 1 t

39、o 6 1 10 to 40 5 to 40 160 B 3,75 to 11,25 3,75 10 to 70 5 to 80 750 C 3 to 12 1 10 to 70 5 to 80 750 5 Test materials The materials used in Europe for winter maintenance are very different. The sodium chloride (NaCl) has different granulometries according to the mine or production type, the humidit

40、y of these products is very variable too. For this reason, the test can be done with any kind of sodium chloride for solid material; the following characteristics shall be indicated in the report: NaCl content (%); humidity (%); granulometry (3 sieves minimum for a vacuum salt and 5 sieves minimum f

41、or rock salt and sea salt); anti-caking agent (nature and concentration). The characteristics of materials shall be determined in laboratory by using a sample of material used for the test. An official certificate of material delivered by material supplier shall be attached to the test report. DD CE

42、N/TS 15597-2:2012CEN/TS 15597-2:2012 (E) 8 The de-icing material shall be protected from atmospheric moisture agent, during storage, to avoid changes in the original characteristic during storage period. The salt solution (sodium chloride, calcium chloride, magnesium chloride) shall have a concentra

43、tion between 18 % and 23 % of weight. In case of spreader type for liquid thawing media the kind of salt solution (brine) used for test shall be described: sodium chloride, calcium chloride or magnesium chloride, or other de-icing material; salt concentration, in percentage of weight; density, in kg

44、/dm3. 6 Certification procedure 6.1 Principle of qualification procedure The qualification procedure of the spreaders includes two test types, one static and one dynamic. The static test enables assessment of the regularity of material flow and the accuracy of quantity, it is carried out with moving

45、 the spreader stationary. The dynamic test enables assessment of salt spreading pattern, it is carried out by driving the spreading vehicle during spreading operation on a measurement area. According to the type of spreader tested, the qualification procedure sets the functioning parameters of the m

46、achine. These spreading parameters are different for the static and dynamic tests. Each spreader type, in order to be qualified, has to meet the requirements of the two tests (static and dynamic). During a qualification, it is forbidden to modify the original calibration of the spreader. Any calibra

47、tion involves the cancellation of the current qualification procedure. The weighing equipment, for both tests, shall be certified with a precision of 1 %. The measurement area sizes shall be defined with a precision of 1 %. 6.2 Identification and requirements on spreader types A spreader type includ

48、es a spreader and a control box. The spreader and the control box have to be identified in the manufacturers production (for instance, model number) and shall be in accordance with the actual European standards. The modification of the components influencing the spreading performances defined in Ann

49、ex A involves the definition of a new machine model, a new procedure of qualification shall be realised for this new model. If the model can work with pre-wetted salt, the qualification shall be done with not pre-wetted and pre-wetted salt. The certificate will have the sentence “It can work with not pre-wetted and pre-wetted salt“ or “It can work with pre-wetted salt. It meets the requirements of CEN/TS 15597-2 only with pre-wetted salt“. If the machine cannot work with pre-wet