BS DD 221-1997 General guidance for the marking of gas appliances《气体器具作标记的一般指南》.pdf

《BS DD 221-1997 General guidance for the marking of gas appliances《气体器具作标记的一般指南》.pdf》由会员分享，可在线阅读，更多相关《BS DD 221-1997 General guidance for the marking of gas appliances《气体器具作标记的一般指南》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、DRAFT FOR DEVELOPMENT DD 221:1997 CR 1472:1997 General guidance for the marking of gas appliances ICS 27.060.20DD221:1997 This Draft for Development, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effe

2、ct on 15 December 1997 BSI 04-1999 First published 1995 Second edition December 1997 The following BSI reference relates to the work on this publication: Committee reference GSE/-/4 ISBN 0 580 28690 8 Committees responsible for this Draft for Development The preparation of this Draft for Development

3、 was entrusted to Technical Committee GSE/-/4, Briefing committee for CEN/PC3, upon which the following bodies were represented: Boiler and Radiator Manufacturers Association Limited British Combustion Equipment Manufacturers Association British Gas Plc Cesa The Association of Catering Equipment Man

4、ufacturers and Importers Co-opted Member Consumer Policy Committee of BSI Council for Registered Gas Installers Department of the Environment Construction Sponsorship Directorate Department of Trade and Industry Consumer Safety Unit, CA Division Gas Consumers Council Health and Safety Executive Inst

5、itution of Gas Engineers LP Gas Association Society of British Gas Industries Amendments issued since publication Amd. No. Date CommentsDD221:1997 BSI 04-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of CR 1472 3DD221:1997 ii BSI 04-1999 National

6、 foreword This Draft for Development has been prepared by Technical Committee GSE/-/4, and is the English language version of CR1472:1997, published by the European Committee for Standardization (CEN). It supersedes DD221:1995 which is withdrawn. It is being issued in the Draft for Development serie

7、s of publications and is of a provisional nature. It should be applied on this provisional basis so that information and experience of its practical application may be obtained. A review of this Draft for Development will be carried out not later than2years after its publication. Notification of the

8、 start of the review period, with a request for the submission of comments from users of this Draft for Development, will be made in an announcement in Standards Update. According to the replies received the responsible BSI Committee will judge whether the Draft for Development can be converted into

9、 a British Standard or what other action should be taken. Observations which it is felt should receive attention before the official call for comments will be welcomed. These should be sent to the Secretary of BSI Committee GSE/-/4 at BSI,389 Chiswick High Road, London,W44AL, giving the document ref

10、erence and clause number and proposing, where possible, an appropriate revision of the text. This Draft for Development is not to be regarded as a British Standard. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theCR title page, pages 2 to 7 and a bac

11、k cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.CEN REPORT RAPPORT CEN CEN BERICHT CR 1472 August 1997 ICS Supersedes CR 1472:1994 Descriptors: English version General guida

12、nce for the marking of gas appliances Indications gnrales pour le marquage des appareils gaz Allgemeiner Leitfaden fr die Kennzeichnung von Gasgerten This CEN Report was approved by CEN on2April1997. It has been drawn up by the ad hoc Group “Marking of gas appliances” of the CEN Programming Committe

13、e “Gas” (PC3). CEN members are the national standards of bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization

14、 Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CR 1472:1997CR1472:1997 BSI 04-1999 2 Foreword The ad hoc Gro

15、up “Marking of gas appliances” of the CEN Programming Committee “Gas” (PC3) prepared this guidance document. On1997-04-02, the CEN Technical Board approved this document for publication as a CEN Report. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 3.1 direct country of

16、 destination 3 3.2 indirect country of destination 3 3.3 manufacturer 3 4 Marking of the appliance 3 5 Marking of the packaging 4 6 Utilization of symbols on the appliance and packaging 4 6.1 Information on the appliance and packaging, in accordance with clauses 4 and 5, which has to be given in the

17、 form of symbols 4 6.2 Other optional information 5 Annex A (informative) Comments 7 Table 1 Symbols of the types of gas 5 Table 2 Means of identification of types of gas in use in the various countries 6CR1472:1997 BSI 04-1999 3 1 Scope This document comprises a list of recommendations for Technica

18、l Committees, whose responsibility it is to decide which of these they wish to incorporate in Standards. These recommendations are based on the principles stated hereafter: 1) To supplement the requirements for marking of the appliance and its packaging, given by Essential Requirement1.2.3 of the EU

19、 Directive90/396/EEC Gas appliances, with information corresponding to the countries of destination of the appliance. In view of the differences across Europe with respect to the distribution of gases and the installation of appliances, the identification of the suitability of an appliance is only e

20、xplicit if the appliance category is mentioned in combination with the country of destination. This information has therefore been considered as essential for the safe use of gas appliances. 2) To establish a link between country, category, gas and pressure. The marking of this information, in effec

21、t, constitutes a coherent whole which is intended to give unambiguous information about the use of the appliance concerned. 3) To use symbols in place of texts in the national languages, while establishing two levels of symbols, obligatory (see6.1) or optional (see6.2), in order to take into account

22、 national practices declared by CEN Members. The ad hoc Group Marking of gas appliances has restricted its recommendations to those which apply to all relevant Technical Committees of PC3. Other information can appear on the appliance or on the packaging. All the following texts are only informative

23、 in the context of this CR, but they serve as model texts for appliances standards. 2 Normative references This CEN report incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications a

24、re listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this CEN report only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 437, Test gases Test pres

25、sures Appliance categories. EN 23166:1993, Codes for the representation of names of countries. EN 60335-1-1994, Safety of household and similar electrical appliances Part1: General requirements. 3 Definitions For the purposes of this document, the following definitions apply: 3.1 direct country of d

26、estination a country for which the appliance has been certified and which is specified by the manufacturer as the intended country of destination. At the time of putting the appliance on the market and of installation, the appliance shall be capable of operating, without adjustment or modification,

27、with one of the gases distributed in the country concerned, at the appropriate normal pressure. More than one country can be specified if the appliance, in its current state of adjustment, can be used in each of these countries 3.2 indirect country of destination a country for which the appliance ha

28、s been certified, but for which, in its present state of adjustment, it is not suitable. Subsequent modification or adjustment is essential in order that it can be utilised safely and correctly in that country 3.3 manufacturer the person responsible for designing and manufacturing a product covered

29、by the directive, with a view to placing it on the Community market on his own behalf NOTEThis definition comes from the guide to the implementation of Community harmonization directives based on the new approach and of global approach the comments of which are in the informativeAnnex A of this docu

30、ment. 4 Marking of the appliance Each appliance shall carry at least the following information, in a visible (possibly after the removal of part of the case or of a cover) and readable way for the installer as well as in an indelible way either directly or on one or more data plates and/or labels fi

31、rmly and durably attached to the appliance: the CE marking; the manufacturers name and/or identification symbol; the trade name of the appliance; the type of electrical supply used, if applicable;CR1472:1997 4 BSI 04-1999 the type of gas, in relation to the pressure and/or the pressure couple, for w

32、hich the appliance has been adjusted; any pressure indication shall be identified in relation to the corresponding category index; the direct country or countries of destination of the appliance; the appliance category or categories: if more than one appliance category is specified, each of these ca

33、tegories shall be identified in relation to the appropriate country or countries of destination; the last two digits of the year in which the CE marking was affixed. No other information shall be included on the appliance if this could lead to confusion with regard to the current state of adjustment

34、 of the appliance and the corresponding appliance category (or categories) and the direct country (or countries) of destination. If an adjustment is necessary on the appliance in order to change from one pressure to the other within a pressure couple, only the pressure corresponding to the current a

35、djustment of the appliance shall be indicated. The indelibility of the marking shall be checked by a test carried out in accordance with7.14 of EN60335-1:1994. The identification symbol may be a logo, or a number allocated by the notified body responsible for the production surveillance. 5 Marking o

36、f the packaging The packaging shall carry at least the following information: the type of gas, in relation to the pressure and/or the pressure couple, for which the appliance has been adjusted; any pressure indication shall be identified in relation to the corresponding category index; the direct co

37、untry or countries of destination of the appliance; warnings related to possible restrictions on use, specifying in particular that the appliance has to be installed in areas where there is sufficient ventilation 1) ; the appliance category or categories : if more than one appliance category is spec

38、ified, each of these categories shall be identified in relation to the appropriate country or countries of destination. Information on the appliance to be seen and read once packaged are considered as meeting those requirements. No other information shall be included on the packaging if this could l

39、ead to confusion with regard to the current state of adjustment of the appliance and the corresponding appliance category (or categories) and the direct country (or countries) of destination. If an adjustment is necessary on the appliance in order to change from one pressure to the other within a pr

40、essure couple, only the pressure corresponding to the current adjustment of the appliance shall be indicated. 6 Utilization of symbols on the appliance and packaging 6.1 Information on the appliance and packaging, in accordance with clauses4 and5, which has to be given in the form of symbols 6.1.1 E

41、lectrical supply The marking concerning electrical values shall be in conformity with EN60335-1. 6.1.2 Type of gas In order to represent all of the category indices corresponding to the adjustment of an appliance, the symbol of the reference gas shall be used which is common to all of these indices,

42、 in accordance withTable 1. 1) A cross-reference to the technical instructions is not sufficient.CR1472:1997 BSI 04-1999 5 Table 1 Symbols of the types of gas 6.1.3 Gas supply pressure The gas supply pressure may be expressed uniquely by the numerical value using the unit (mbar). Nevertheless, if it

43、 is necessary to explain the value, the symbol p shall be used. 6.1.4 Country of destination In accordance with EN23166, the names of countries shall be represented by the following codes: 6.1.5 Category The category can be expressed uniquely by its designation in accordance with EN437. Nevertheless

44、, if it is necessary to explain it, the term “Category” shall be symbolized by Cat. 6.2 Other optional information The symbols given below are not obligatory, but are recommended under the title “preferential”, and to the exclusion of any other symbol, to avoid the use of many and different markings

45、. 6.2.3 Additional indication related to the type of gas: as well as the symbol of the type of gas as given in6.1.2, its declared means of identification (according toTable 2) may be added. Symbol of the type of gas Corresponding category index First family a : G 110 1a G 120 1b G 130 1c G 150 1e Se

46、cond family : G 20 2H, 2E, 2E+, 2Esi b , 2Er b , 2ELL b , 2E(S)B b , 2E(R)B b G 25 2L, 2Esi c , 2Er c , 2ELL c , 2E(S)B c , 2E(R)B c Third family : G 30 3B/P, 3+ df , 3B G 31 3+ ef , 3P a If, in its current state of adjustment, the appliance can use gases from different groups, all the reference gas

47、es corresponding to these groups shall be indicated. b When the appliance is adjusted for G20. c When the appliance is adjusted for G25. d Only applies to appliances which do not need any adjustment between G30 and G31, or to appliances which need an adjustment and which are adjusted for G30. e Only

48、 applies to appliances which need an adjustment between G30 and G31 and which are adjusted for G31. f For appliances which need an adjustment between G30 and G31, the label concerning the adjustment to the other gas and the other pressure of the pressure couple shall be supplied with the technical i

49、nstructions. AT Austria GR Greece BE Belgium IE Ireland CH Switzerland IS Iceland DE Germany IT Italy DK Denmark LU Luxemburg ES Spain NL Netherlands FI Finland NO Norway FR France PT Portugal GB United-Kingdom SE Sweden 6.2.1 Nominal heat input of a burner Q n 6.2.2 Nominal heat input of all appliance burners CQ nCR1472:1997 6 BSI 04-1999 Table 2 Means of identification of types of gas in use in the various countries Type of gas G 110 G 120 G 130 G 150 G 20 G 25 G 30 G 31 Country code AT Erdgas Flssiggas B