BS AU 50-3 8-1985 Tyres and wheels - Valves - Code of practice for the selection and care of tyre inflation valves for commercial vehicles - Section 8a Code of practice for the sel.pdf

《BS AU 50-3 8-1985 Tyres and wheels - Valves - Code of practice for the selection and care of tyre inflation valves for commercial vehicles - Section 8a Code of practice for the sel.pdf》由会员分享，可在线阅读，更多相关《BS AU 50-3 8-1985 Tyres and wheels - Valves - Code of practice for the selection and care of tyre inflation valves for commercial vehicles - Section 8a Code of practice for the sel.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 50-3.8:1985 Incorporating Amendment No. 1 Tyres and wheels Part 3: Valves Section 8: Code of practice for the selection and care of tyre inflation valves for commercial vehicles UDC 629.113.012.551 396.2 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED B

2、Y COPYRIGHT LAWBS AU 50-3.8:1985 This British Standard, having been prepared under the direction of the Automobile Standards Committee, was published under the authority of the Board of BSI and comes into effect on 28 February 1985 BSI 06-2001 The following BSI references relate to the work on this

3、standard: Committee reference AUE/4 Draft for comment 84/71549 DC ISBN 0 580 14327 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/4 upon which the following bodies were

4、 represented: Agricultural Engineers Association British Industrial Truck Association British Pressure Gauge Manufacturers Association British Rubber Manufacturers Association Bus and Coach Council Department of Transport London Transport Executive Ministry of Defence Motor Cycle Association of Grea

5、t Britain Motor Industry Research Association Retread Manufacturers Association Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No. Date of issue Comments 11053 June 2001 Indicated by a sidelineBS AU 50-3.8:1985 BSI 06-2001 i

6、Contents Page Committees responsible Inside front cover Foreword ii 8.1 Scope 1 8.2 Valve selection by vehicle manufacturer 1 8.3 Types of valves 1 8.4 Valve fitting checks 2 8.5 Valve accessibility 2 8.6 In-service valve checks 2 8.7 Check list for care of inflation valves for commercial vehicles 2

7、BS AU 50-3.8:1985 ii BSI 06-2001 Foreword This section of BS AU 50-3 has been prepared under the direction of the Automobile Standards Committee. This code of practice gives guidance to vehicle manufacturers on the initial steps to be taken in selecting valves for commercial vehicles wheels. Recomme

8、ndations are also given on the care of valves, which if followed would lead to improved road safety. The data in this code of practice are based on the information provided by the Society of Motor Manufacturers and Traders Ltd. Tyre, wheel, rim and valve requirements are given in the following parts

9、 and sections of BS AU 50: Tyres and wheels: Part 1: Tyres; Section 0: General; Section 1: Car tyres; Section 2: Commercial vehicle tyres; Section 3: Off-the-road tyres; Section 4: Agricultural vehicle tyres; Section 5: Industrial vehicle tyres; Section 6: Motor cycle and scooter tyres; Part 2: Whee

10、ls and rims; Section 0: General (including terms and definitions, and construction and workmanship); Section 1: Rim profiles and dimensions (including openings for valves); Section 2: Wheel naves and hub centres; Section 3: Wheel and hub studs and nuts, and bolts 1) ; Section 4: Supplementary data f

11、or future developments 1) ; Section 5: Road wheels manufactured wholly or partly of light alloy for passenger cars; Section 6: Specification for road wheels manufactured wholly or partly of light alloy for mopeds and motor cycles; Section 7: Code of practice for the selection and care of wheels for

12、commercial vehicles 1) ; Section 8: Code of practice for the selection and care of wheels for passenger cars (including caravans and light trailers) 1) ; Part 3: Valves; Section 1: Valve dimensions; Section 2: Tyre valve threads 5V1, 5V2, 6V1 and 8V1; Section 3: Tyre valve threads 9V1, 10V2, 12V1 an

13、d 13V1; Section 4: Tyre valve threads 8V2, 10V1, 11V1, 13V2, 15V1, 16V1, 17V1, 17V2, 17V3, 19V1 and 20V1; Section 5: Dimensions for ISO core chamber No. 1 for tyre inflation valves; Section 6: Dimensions for ISO core chamber No. 2 for tyre inflation valves; Section 7: Code of practice for the select

14、ion and care of tyre inflation valves for passenger cars (including caravans and light trailers); Section 8: Code of practice for the selection and care of tyre inflation valves for commercial vehicles. 1) In preparation.BS AU 50-3.8:1985 BSI 06-2001 iii A British Standard does not purport to includ

15、e all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i

16、 to iv, pages 1 to 3 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Sidelining in this document indicates the most recent changes by amendment.iv blankBS AU 50-3.8:1985 BSI 06-2001 1 8.1 Scope This section of BS AU 50-3 gives recomm

17、endations for vehicle manufacturers on the initial steps to be taken in selecting valves for commercial vehicle wheels and recommendations for the care of valves for the user. 8.2 Valve selection by vehicle manufacturer When selecting a valve for a wheel and tyre assembly it is important to ensure t

18、hat the correct choice is made. Basic factors which influence this choice are: a) type of tyre (tube type or tubeless); b) inflation pressure of the tyre; c) type of wheel. The basic choice is between tube type and tubeless tyres. This would generally be decided by the vehicle design and performance

19、 requirements and the valve type is therefore predetermined. 8.3 Types of valves 8.3.1 General Valves are available in the following two basic types: a) tubeless type valves, which can be either of the rubber snap-in or metal clamp-in types (see 8.3.2); b) tube type valves, which can be either one p

20、iece or two piece valves (see 8.3.3). 8.3.2 Tubeless valves 8.3.2.1 Rubber snap-in valves. Rubber snap-in valves are available in several different lengths and sizes and care should be exercised in selecting the correct size to suit the rim hole, and the most suitable length for ease of access so as

21、 not to be damaged in service. The valve stem is threaded internally and externally for fitment of the valve core and valve sealing cap respectively. It is essential that special care should be taken when fitting rubber snap-in valves. First the rim hole should be inspected to ensure it is in good c

22、ondition and free from burrs and sharp edges which can damage the rubber body of the valve. Then the rubber body of the valve should be lubricated with an approved lubricant for ease of fitting and inserted into the rim hole using a special valve insertion tool. To ensure that the valve is correctly

23、 located, it is essential that the moulded fitting line on the rubber valve body passes completely through the rim valve hole. NOTE This type of valve is suitable for tyre inflation pressures up to a maximum of 475 kPa (4.7 bar or 69 psi). 8.3.2.2 Clamp-in valves. Metal clamp-in valves are available

24、 in a variety of sizes. It should always be ensured that the correct valve is fitted for the rim hole size and application. Clamp-in valves for tubeless truck tyres are clamped into the rim and an airtight seal is achieved by means of a hexagonal nut and rubber grommet. During fitting it should be e

25、nsured that the valve is correctly located relative to the wheel components to ensure ease of access for pressure checking and adjustment. 8.3.3 Tube valves 8.3.3.1 One piece valves. These are rubber based or rubber covered straight stem valves which are vulcanized to the inner tube and bent when re

26、quired to given angles and dimensions. 8.3.3.2 Two piece valves. These consist of a rubber “spud” and a pre-bent stem (dimensions according to requirement) which is attached to the “spud” when required. The two piece valve is sometimes referred to as “universal”. It is essential that care is exercis

27、ed to ensure correct location of the valve in the flap (where fitted) and in the rim aperture to prevent unnecessary strain on the valve in use.BS AU 50-3.8:1985 2 BSI 06-2001 If the valve is of the universal screw-on type it is essential that it should be fitted with the correct rubber washer in go

28、od condition and sufficiently tightened to form an airtight seal by continuing to tighten down the stem a further two turns after the stems metal washer has touched the rubber washer. The valve should be aligned by additional tightening. 8.4 Valve fitting checks Whenever a tubeless tyre or a tyre an

29、d tube assembly is inflated or the inflation pressure is checked and/or adjusted it is essential that a final check should be made that the valve has correctly sealed. Leaking valve cores should be replaced. It should not be attempted to cure a leaking valve by extra tightening as this may damage th

30、e core seal. It should be ensured that the valve hole in the rim is in good condition and is free from burrs which could damage the valve and cause deflation of the tyre. A valve cap of the type which acts as an additional air seal and which protects the core from dirt, dust and water should always

31、be fitted. 8.5 Valve accessibility Where access to the valve for inflation or pressure checking purposes is difficult, a valve extension may be used. If extensions are required to assist accessibility for inflation, deflation and pressure checking, it is important that they should be securely attach

32、ed to the valve, preferably by light wrench tightening. Flexible extensions should be suitably supported. It should be ensured that the extension is of the correct length and style to suit the required application. The sealing extension should be fitted with a valve cap, unless the extension preclud

33、es this. 8.6 In-service valve checks New rubber snap-in valves and the rubber components of metal clamp-in valves should always be fitted when fitting new replacement tyres. Rubber covered valves should be examined regularly for splits and cuts. Damaged valves should be replaced immediately. All val

34、ves should be examined regularly for damaged cap threads and/or distorted valve mouth where the cap is fitted. The internal valve core threads should also be examined for cleanliness. If the valve mouth is distorted the valve should be replaced. The metal parts of tubeless or tube valves can become

35、damaged or distorted during their service life. Distortions may have weakened the valve to a point of possible fracture and in such cases the valve should be replaced immediately. It should be ensured that the radiused valve mouth which contacts the cap sealing washer is smooth and without nicks and

36、 burrs which may scuff and tear the cap seal. Damaged cap threads, internal core threads and valve mouths should be repaired with an appropriate and recommended repair tool. 8.7 Check list for care of inflation valves for commercial vehicles The following check list should be used for care of inflat

37、ion valves for commercial vehicles. a) Do ensure the valve and valve fitting is the correct size and type for the wheels and usage, e.g. it is essential that clamp-in valves are used for inflation pressures above 475 kPa (4.7 bar or 69 psi). Do not assume that “any-old” valve or valve fitting is sui

38、table. b) Do regularly check on valve cores for leakage. Replace damaged or leaking cores. Do not attempt to cure leaking valve core by over-tightening. Damage to core seat can easily result. c) Do ensure that valve caps are always fitted and replaced after removal. Sealing type valve caps are prefe

39、rred. Do not leave valve caps on the ground when servicing. They can become damaged or lost.BS AU 50-3.8:1985 BSI 06-2001 3 d) Do ensure that the valve holes in tubeless rims are in good condition and the surrounding area free from rust, pits and burrs. Seek advice if in doubt. Do not attempt to rem

40、ove pits, rust and burrs by grinding or heavy filing. The holes may become irregular in shape and affect valve sealing. e) Do ensure that after fitting a rubber covered snap-in tubeless valve, the indicating ring around the body is fully visible on the outside of the rim. This is an indication of co

41、rrect fitment. Use an approved lubricant. Do not attempt fitment of a snap-in type tubeless valve without the correct mounting tool. Do not use grease or dirty lubricant. f) Do ensure that clamp-in type valves are correctly positioned and securely fitted. Do not use excessive force to tighten clamp-

42、in valve securing nuts. g) Do examine regularly the valves rubber fitments or rubber cover for cracks or splits and examine the metal portions of the valve for distortion and the threads for damage. Ensure that valve mouth is round, smooth and without nicks or burrs which would hinder the sealing qu

43、ality of the cap. If in doubt change the valve or appropriate fitment immediately. Do not attempt to fill cracks or splits with paint, or attempt to repair valve distortions, nor attempt clearing or cleaning of thread or valve mouth without the appropriate and recommended repair tool. h) Do ensure t

44、hat new snap-in valves or clamp-in valve rubber fittings are fitted when replacing tubeless tyres. Do not assume that tyre valves will last forever. i) Do ensure that if valve extensions are used they are the correct type and length for the application and they are securely tightened on to the valve

45、. Flexible extensions should be suitably supported. Do not use an extension if inflation and pressure checking can be achieved without it. j) Do ensure that valves of the universal screw-on type are fitted with the correct rubber washer and sufficiently tightened to form a seal, by continuing to scr

46、ew down the stem a further two complete turns after the stems metal washer has touched the rubber washer. Align valve stem by additional tightening. Do not overtighten universal screw-on type valves or omit rubber washers nor align valves by unscrewing stem.BS AU 50-3.8:1985 BSI 389 Chiswick High Ro

47、ad London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendmen

48、t or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would

49、 inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from th