BS AU 222-1988 Method of evaluating surface and material flaws of disc brake pads after testing《试验后圆盘制动垫表面及材料缺陷评定方法》.pdf

《BS AU 222-1988 Method of evaluating surface and material flaws of disc brake pads after testing《试验后圆盘制动垫表面及材料缺陷评定方法》.pdf》由会员分享，可在线阅读，更多相关《BS AU 222-1988 Method of evaluating surface and material flaws of disc brake pads after testing《试验后圆盘制动垫表面及材料缺陷评定方法》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AUTOMOBILE SERIES BSAU 222:1988 ISO7629:1987 Method of evaluating surface and material flaws of disc brake pads after testing ISO title: Road vehicles Brake linings Disc brake pads Evaluation of surface and material flaws after testing UDC 629.11597.6:620.1:001.818+.004.64BSAU222:19

2、88 This BritishStandard, having been prepared under the directionof the Automobile Standards Committee, was published under the authority ofthe Board of BSI and comes into effect on 29January1988 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/11

3、 Draft for comment 84/78305 DC ISBN 0 580 16361 X Committees responsible for this BritishStandard The preparation of this BritishStandard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/11, upon which the following bodies were represented: Automobile Associatio

4、n British Fluid Power Association British Friction Materials Council Department of Transport Freight Transport Association London Transport Executive Motor Industry Research Association National Caravan Council Ltd. Society of Motor Manufacturers and Traders Transport and General Workers Union Amend

5、ments issued since publication Amd. No. Date of issue CommentsBSAU222:1988 BSI 02-2000 i Contents Page Committees responsible Inside front cover National foreword ii 0 Introduction 1 1 Scope and field of application 1 2 Identification of defects 1 3 Measuring equipment 1 4 Measurement method 1 5 Exp

6、ression of results 1 Figure 1 Example of crack (type I flaw) 2 Figure 2 Example of edge flaking (type II flaw) 2 Figure 3 Example of blistering or pitting (type III flaw) 3 Figure 4 Example of lining separation from support and material lamina separation (type IV flaw) 3 Figure 5 Centring of the gri

7、d 4BSAU222:1988 ii BSI 02-2000 National foreword The BritishStandard has been prepared under the direction of the Automobile Standards Committee and is identical with ISO7629:1987 “Road vehicles Brake linings Disc brake pads Evaluation of surface and material flaws after testing”, published by the I

8、nternational Organization for Standardization (ISO). Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a BritishStandard without deviation. Some terminology and certain conventions are not identical with those used in BritishStandard

9、s; attention is drawn especially to the following. Wherever the words “International Standard” appear referring to this standard, they should be read as “BritishStandard”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are respon

10、sible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to4 and a back cover. This standard has been updated (see copyright d

11、ate) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BSAU222:1988 BSI 02-2000 1 0 Introduction Disc brake pads may show damage after being subjected to vehicle or laboratory tests. This International Standard has the purpose of specif

12、ying a method of describing some of this damage. 1 Scope and field of application This International Standard identifies the types of flaws of surface and material after testing of disc brake pads, and specifies the method of measuring these flaws and of setting out the results. This International S

13、tandard applies to disc brake pads intended for fitting to the brakes of road vehicles. 2 Identification of defects The presence of a flaw is decided only if it is detectable with the naked eye. Flaws to be considered are of four types: Type I Cracks (seeFigure 1) Type II Edge flaking (seeFigure 2)

14、Type III Blistering and pitting (seeFigure 3) Type IV Material separation from the support or material lamina separation (seeFigure 4) 3 Measuring equipment Transparent millimetric grid of sufficient area to cover the whole area on which defects are to be measured (seeFigure 5). 4 Measurement method

15、 4.1 Preliminary measurements 4.1.1 On the lining, prior to testing, measure and record: a) the lining height measured on the lining median line, H, in millimetres (seeFigure 1), or, for non-symmetrical shapes, the maximum height; b) the friction surface area, A 0 , in square millimetres. 4.1.2 Dete

16、rmine a reference point A, located at the middle of height H (seeFigure 5). 4.2 Measurement of flaws 4.2.1 Flaws of type1(seeFigure 1) Measure the length, l, of each crack. Position the millimetric grid on point A, as illustrated inFigure 5. Count the cracks within the10mm 10mm area which has the gr

17、eatest density of cracks. All cracks partially crossing the area are to be included. 4.2.2 Flaws of types II and III (seeFigure 2 andFigure 3) Place the millimetric grid on the work surface. Determine the area of each flaw with the naked eye. NOTEFor simplicity, edge flaking can be characterized bya

18、 b (seeFigure 2). 4.2.3 Flaws of type IV (seeFigure 4) Measure the length, L. 5 Expression of results 5.1 Cracks (type I) 5.1.1 Calculate, as a percentage of the lining heightH, and record: a) length of the longest crack; b) sum of all crack lengths. 5.1.2 Record the greatest number of cracks observ

19、ed per100mm 2 . 5.2 Edge flaking (type II), blistering and pitting (type III) Add all these flaws (types II and III). Calculate the total as a percentage of the surface area A 0 , and record: a) area of the biggest flaw; b) sum of all flaw areas. 5.3 Material separation from support and material lam

20、ina separation (type IV) Calculate, as a percentage of the lining height, H, and record: a) longest separation length; b) sum of all separation lengths.BSAU222:1988 2 BSI 02-2000 Figure 1 Example of crack (type I flaw) Figure 2 Example of edge flaking (type II flaw)BSAU222:1988 BSI 02-2000 3 Figure

21、3 Example of blistering or pitting (type III flaw) Figure 4 Example of lining separation from support and material lamina separation (type IV flaw)BSAU222:1988 4 BSI 02-2000 Figure 5 Centring of the gridblankBSAU 222:1988 ISO7629:1987 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInsti

22、tution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards shoul

23、d make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee

24、 responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, inte

25、rnational and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise reques

26、ted. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services

27、. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967

28、002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrie

29、val system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designation

30、s. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.