BS A 316-1997 Nuts hexagonal slotted (castellated) normal height normal across flats with MJ threads classifications - 600 MPa (at ambient temperature) 120 C 600 MPa (at ambient te.pdf

《BS A 316-1997 Nuts hexagonal slotted (castellated) normal height normal across flats with MJ threads classifications - 600 MPa (at ambient temperature) 120 C 600 MPa (at ambient te.pdf》由会员分享，可在线阅读，更多相关《BS A 316-1997 Nuts hexagonal slotted (castellated) normal height normal across flats with MJ threads classifications - 600 MPa (at ambient temperature) 120 C 600 MPa (at ambient te.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BSA 316:1997 ISO 4147:1997 Aerospace Nuts, hexagonal, slotted (castellated), normal height, normal across flats, with MJ threads, classifications: 600MPa(at ambient temperature)/120 C, 600MPa (at ambient temperature)/235 C, 900MPa (at ambient temperature)/425 C, 110

2、0 MPa (at ambient temperature)/235 C, 1100MPa (at ambient temperature)/315 C, 1100MPa (at ambient temperature)/650 C, 1210MPa (at ambient temperature)/730 C, 1250MPa (at ambient temperature)/235 C and1550MPa (at ambient temperature)/600C Dimensions ICS 49.030.30BSA316:1997 This British Standard, hav

3、ing been prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes intoeffect on 15 November1997 BSI 04-2000 ISBN 0 580 28789 0 National foreword This British Standard reproduces verbatim ISO4147:1997 and implements it as the UK nat

4、ional standard. The UK participation in its preparation was entrusted by Technical Committee ACE/12, Aerospace fasteners and fastening systems, to Subcommittee ACE/12/1, Aerospace fasteners and fastening systems (international), which has the responsibility to: aid enquirers to understand the text;

5、present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommitte

6、e can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using

7、 the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity f

8、rom legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, pages ii to iv, pages1 to3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated i

9、n the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSA316:1997 BSI 04-2000 i Contents Page National foreword Inside front cover Foreword iii Text of ISO 4147 1ii blankBSA316:1997 ii BSI 04-2000 Contents Page Foreword iii Introduction 1 1 Scope

10、1 2 Normative references 1 3 Configuration and dimensions 1 Figure 1 2 Table 1 3 Descriptors: Aircraft industry, fasteners, MJ threads, nuts (fasteners), hexagonal nuts, castle nuts, classification, form specifications, dimensions.BSA316:1997 BSI 04-2000 iii Foreword ISO (the International Organizat

11、ion for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established h

12、as the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Dra

13、ft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75%of the member bodies casting a vote. International Standard ISO4147 was prepared by Technical Committee ISO/TC20, Ai

14、rcraft and space vehicles, Subcommittee SC4, Aerospace fastener systems. This third edition cancels and replaces the second edition (ISO4147:1983), of which it constitutes a technical revision.iv blankBSA316:1997 BSI 04-2000 1 Introduction The dimensions specified in this International Standard have

15、 been determined to satisfy the requirements of the procurement specification of ISO9139. 1 Scope This International Standard specifies the dimensions of hexagon slotted (castellated) nuts, normal height, normal across flats, with MJ threads, of classifications:600MPa 1) /120 C 2) ,600MPa 1) /235 C

16、2) , 900 MPa 1) /425 C 2) , 1100MPa 1) /235 C 2) ,1100MPa 1) /315 C 2) ,1100MPa 1) /650 C 2) , 1 210 MPa 1) /730 C 2) , 1250 MPa 1) /235 C 2)and1550MPa 1) /600 C 2) . These nuts are intended to be used with split pins in conformity with ISO1234. This International Standard is only applicable for the

17、 compilation of aerospace product standards. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revi

18、sion, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO1234:, Split pins 3) . IS

19、O5855-2:1988, Aerospace MJ threads Part2: Limit dimensions for bolts and nuts. ISO8788:1987, Aerospace Fasteners Tolerances of form and position for nuts. ISO9139:, Aerospace Nuts, plain or slotted (castellated) Procurement specification 4) . 3 Configuration and dimensions See Figure 1 and Table 1.

20、Dimensions and tolerances are expressed in millimetres. They apply after any surface coating(s) but before the application of any lubricant. 1) Corresponds to the minimum tensile stress which the nut is able to withstand at ambient temperature without breaking or cracking when tested with a bolt of

21、a higher strength class. 2) Maximum temperature that the nut is able to withstand, without permanent alteration to its original characteristics, after ambient temperature has been restored. The maximum temperature is conditioned by the material or by the surface treatment. 3) To be published. (Revis

22、ion of ISO1234:1976) 4) To be published.BSA316:1997 2 BSI 04-2000 NOTETolerances of form and position shall conform to those specified in ISO8788. Details of form not stated are at the manufacturers discretion. 1) These values, in micrometres, apply before any surface coating(s) is (are) applied. Th

23、e values do not apply to threads the surface texture of which will be as achieved by the usual manufacturing methods. 2) Tooling marks permissible within counterbore. 3) Applies to: height below slots; height of flats (diameter codes060 to240); bottom of counterbore. 4) This dimension also applies t

24、o the upper chamfer. All forms of entry (chamfer or radius) permissible within these limiting dimensions. 5) Diameter M may be tangential to, but shall not intrude on the flats. Figure 1 BSA316:1997 BSI 04-2000 3 Table 1 Diameter code Thread a E F G H J K L M N S Maximum split pin diameter b min. 0,

25、25 0,25 0,25 H15 min. H14 040 MJ40,74H6H 7,6 7 h12 3 5 4 4,2 6,4 0,5 1,3 1 050 MJ50,84H6H 8,7 8 3,75 6,2 5 5,2 7,4 1,7 1,4 060 MJ614H5H 10,9 10 4,5 6,9 9 6 6,3 9,3 070 MJ714H5H 12 11 5,25 8,1 10 7 7,3 10,2 2,1 1,8 080 MJ814H5H 14,3 13 6 8,8 11 8,3 12,2 100 MJ101,254H5H 18,9 17 7,5 11,1 13 10,3 16 0,

26、6 2,6 2,3 120 MJ121,254H5H 21,1 19 9 12,6 16 12,3 18 140 MJ141,5 4H5H 24,5 22 h13 10,5 14,9 18 14,4 21 3,2 2,9 160 MJ161,54H5H 26,8 24 12 16,4 22 16,4 23 180 MJ181,54H5H 30,2 27 13,5 18,7 25 18,4 26 4 3,7 200 MJ201,54H5H 33,6 30 15 20,2 28 20,4 29 220 MJ221,54H5H 35,8 32 16,5 21,7 30 22,4 30,9 240 M

27、J2424H5H 40,4 36 18 23,7 32 24,5 34,9 a In accordance with ISO5855-2 b For information, in conformity with ISO1234 for the split pin maximum diameter but not for the split pin maximum diameter/thread diameter combination 0 0,3 +0,6 0 +0,8 0BSA 316:1997 ISO 4147:1997 BSI 389 Chiswick High Road London

28、 W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision.

29、 Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secr

30、etary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying st

31、andards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishSt

32、andards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details

33、on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Members

34、hip Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may b

35、e reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and

36、 size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.