BS A 309-1994 Bolts large hexagonal head normal or pitch diameter shank long length MJ threads metallic material coated or uncoated strength classes less than or equal to 1100 MPa .pdf

《BS A 309-1994 Bolts large hexagonal head normal or pitch diameter shank long length MJ threads metallic material coated or uncoated strength classes less than or equal to 1100 MPa .pdf》由会员分享，可在线阅读，更多相关《BS A 309-1994 Bolts large hexagonal head normal or pitch diameter shank long length MJ threads metallic material coated or uncoated strength classes less than or equal to 1100 MPa .pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS A309:1994 ISO9256:1993 Bolts, large hexagonal head, normal or pitch diameter shank, long length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to1100MPa Dimensions UDC 621.882.21:629.7BSA309:1994 This BritishStandard, having been prepared u

2、nder the directionof the Aerospace Standards Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15August1994 BSI01-2000 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for comment 90/79034 DC ISBN 0 580

3、23223 9 Committees responsible for this BritishStandard The preparation of this BritishStandard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/12, upon which the following bodies were represented: The Association of Electronics, Telecommunications and Bu

4、siness EquipmentIndustries British Industrial Fastners Federation Ministry of Defence Society of British Aerospace Companies Ltd. Amendments issued since publication Amd. No. Date CommentsBSA309:1994 BSI 01-2000 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1

5、 2 Normative references 1 3 Configuration and dimensions 1 Figure 1 Configuration for diameter codes030 and040 2 Figure 2 Configuration for diameter codes050 to080 2 Table 1 3 List of references Inside back coverBSA309:1994 ii BSI 01-2000 National foreword This BritishStandard has been prepared unde

6、r the direction of the Aerospace Standards Policy Committee. It is identical with ISO9256:1993 Aerospace Bolts, large hexagonal head, normal or pitch diameter shank, long length MJ threads, metallic material, coated or uncoated, strength classes less than or equalto1100MPa Dimensions published by th

7、e International Organization for Standardization (ISO). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from lega

8、l obligations. Cross-references International Standard Corresponding BritishStandard ISO286-2:1988 BS EN20286 ISO system of limits and fits Part2:1992 Tables of standard tolerance grades and limit deviations for holes and shafts (Identical) ISO3353:1992 BS2A231:1992 Rolled threads for bolts. Lead an

9、d runout requirements (Identical) ISO5855-2:1988 BS6293 Aerospace MJ threads Part2:1994 Limit dimensions for bolts and nuts (Identical) Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to4, an inside back cover and a back cover. This standard has be

10、en updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BSA309:1994 BSI 01-2000 1 1 Scope This International Standard specifies the dimensions of large hexagonal head bolts, with normal or pitch diameter shank,

11、 and long length MJthreads, in metallic material, coated or uncoated, with strength classes less than or equal to1100MPa. It is intended for the drawing up of aerospace product standards. 2 Normative references The following standards contain provisions which, through reference in this text, constit

12、ute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of th

13、e standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO286-2:1988, ISO system of limits and fits Part2: Tables of standard tolerance grades and limit deviations for holes and shafts. ISO3353:1992, Aerospace Rolled threads for bolts Lead

14、and runout requirements. ISO5855-2:1988, Aerospace MJ threads Part2: Limit dimensions for bolts and nuts. 3 Configuration and dimensions See Figure 1 and Figure 2 and Table 1. Dimensions and tolerances are expressed in millimetres. They are applicable after any surface coating, but before the applic

15、ation of any lubricant. Details of form not stated are left to the manufacturers discretion. BSA309:1994 2 BSI 01-2000 Figure 1 Configuration for diameter codes030 and040 NOTEFor other dimensions, see Figure 1. Figure 2 Configuration for diameter codes050 to080BSA309:1994 BSI 01-2000 3 Table 1 Diame

16、ter code Thread a D 1 D 2 b D 3 D 4 D 5 D 6 normal pitchdiameter nom. tol. nom. tol. min. nom. tol. min. H13 c 030 MJ30,54h6h 3 h12 c 2,68 0,13 6,4 2,3 6,5 1 040 MJ40,74h6h 4 3,54 7,4 3 0,5 7,5 050 MJ50,84h6h 5 4,48 8,3 3,4 8,4 5,25 060 MJ614h6h 6 5,35 10,2 4,2 10,3 6,25 1,4 070 MJ714h6h 7 6,35 11,2

17、 5,2 11,3 7,25 080 MJ814h6h 8 7,35 13,2 6,2 13,3 8,25 Diameter code E F G H J K L 1 def L 2 def L 3 L 4 e R S min. min. max. nom. tol. nom. tol. 030 7,6 1,55 3,4 0,5 0,4 2 12 14 to42 0,3 0,4 7 h12 c 040 8,7 1,8 3,9 14 16 to56 8 050 9,8 1,35 2 3 3,7 0,5 4 16 20 to70 0,5 9 h13 c 060 12 1,6 2,3 3,5 4,5

18、 0,7 18 22 to84 0,7 11 070 13,2 1,85 2,7 4 4,95 20 24 to98 12 080 15,5 2,1 3 4,5 5,8 0,6 22 26 to112 14 a In conformity with ISO5855-2. b D 2max.u actual S. c See ISO286-2. d First length, corresponding to first L 4length. e Increments: 2 for L 4 u 100 4 for L 100 If greater lengths are necessary, t

19、hey shall be chosen using these increments. f Conditions L 1 min. and L 2 max. cannot be obtained simultaneously. 0 0,5 0 0,5 0 0,3 0 0,3 0 0,3 0 0,24 blankBSA309:1994 BSI 01-2000 List of references See national foreword.BS A309:1994 ISO9256:1993 BSI 389 Chiswick High Road London W4 4AL BSIBritishSt

20、andardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishSta

21、ndards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technic

22、al committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for a

23、ll BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless othe

24、rwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products

25、and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration.

26、Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored

27、 in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade

28、 designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.