BS 9100-1983 Specification for capability approval for custom-built capacitors and capacitor modules generic data and methods of test《定制电容器和电容器模件的性能鉴定规范 通用数据和试验方法》.pdf

《BS 9100-1983 Specification for capability approval for custom-built capacitors and capacitor modules generic data and methods of test《定制电容器和电容器模件的性能鉴定规范 通用数据和试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS 9100-1983 Specification for capability approval for custom-built capacitors and capacitor modules generic data and methods of test《定制电容器和电容器模件的性能鉴定规范 通用数据和试验方法》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 9100:1983 Incorporating Amendment No.1 Specification for Capability approval for custom-built capacitors and capacitor modules: Generic data and methods of test UDC 621.319.4BS9100:1983 This BritishStandard, having been prepared under the directionof the Electronic Components Sta

2、ndards Committee, was published underthe authority of the BoardofBSI and comesinto effect on 30June1983 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ECL/4 Draft for comment81/27319 DC ISBN 0 580 11987 4 Committees responsible for this BritishStand

3、ard This BritishStandard was published under the direction of the Electronic Components Standards Committee ECL/-. Its preparation was entrusted to Technical Committee ECL/4 upon which the following bodies were represented: Electronic Components Industry Federation Electronic Engineering Association

4、 Ministry of Defence National Supervising Inspectorate Post Office Society of British Aerospace Companies Limited Telecommunication Engineering and Manufacturing Association (TEMA) Amendments issued since publication Amd. No. Date of issue Comments 7508 October1993 Indicated by a sideline in the mar

5、ginBS9100:1983 BSI 12-1999 i Contents Page Committees responsible Inside front cover Foreword iii 0 Introduction 1 Section 1. Principles and mandatory procedures 1.1 General matters 1 1.1.1 Scope 1 1.1.1.1 Custom-built capacitors 1 1.1.1.2 Custom-built capacitor modules 1 1.1.2 Related documents 1 1

6、.1.3 Terminology 2 1.1.4 Letters, symbols, signs and abbreviations 2 1.1.5 Graphical symbols 2 1.1.6 Marking of the component and package 2 1.1.7 Eligibility for capability approval 2 1.1.8 Delayed delivery 2 1.1.9 Certified test records 3 1.1.10 Preferred climatic categories 3 1.1.11 Unchecked para

7、meters 3 1.1.12 Ordering information 3 1.1.13 Release prior to completion of Group B tests 3 1.1.14 Supplementary procedure for reduced inspection 3 1.1.15 Rectification 3 1.2 Test procedures 3 1.3 Capability approval and maintenance procedures 3 1.3.1 Description of capability 3 1.3.2 Programme for

8、 capability approval 3 1.3.2.1 Capability qualifying components (CQCs) for capability assessment 4 1.3.2.2 Guidance on the content of the programme for capability approval 5 1.3.2.3 Performance of capability approval programme 6 1.3.3 Failure procedure 7 1.3.4 Abstract of description of capability 7

9、 1.3.5 Maintenance of capability approval 7 1.3.5.1 Inspection requirements for maintenance of capability 7 1.3.5.2 Procedure to be followed in the event of failures during periodic inspection 7 1.3.6 Capability approval report 7 1.3.7 Review, suspension and withdrawal of capability approval 7 1.4 I

10、nspection to the customers detail specification 8 Section 2. Guidance on the preparation of customers detail specifications 2.1 Basic information 8 2.1.1 Originator of the detail specification 8 2.1.2 Numbering of the customer detail specification 8 2.1.3 Description of the component and its intende

11、d application 8 2.1.4 Outline drawing and dimensions 8BS9100:1983 ii BSI 12-1999 Page 2.1.5 Required conditions of use and associated characteristics 9 2.1.6 Related documents 9 2.1.7 Additional information 9 2.1.8 Ordering instructions 9 2.2 Quality conformance inspection requirements 9 2.2.1 Lot-b

12、y-lot 9 2.2.2 Periodic tests 9 2.3 Certified test records 9 2.4 Authentication 9 Section 3. Manufacturers guidance to customers 3.1 Introduction 9 3.2 Component technology 10 3.3 Materials construction and packages 10 3.4 Policy and information on design data 10 3.5 Quality conformance inspection sc

13、hedules 10 3.5.1 Lot-by-lot tests 10 3.5.2 Periodic tests 10 3.6 Guidance on the ratings and characteristics which the customer should specify 10 Appendix A Example of an abstract of description of capability for inclusion in PD9002 11 Appendix B Example of a customers detail specification 12 Figure

14、 1 Description of capability 5 Table 1 Ratings and characteristics 13 Table 2 Lot-by-lot inspection 14 Table 3 Typical example of tests carried out on CQCs for one dielectric relevant to one declared capability 15BS9100:1983 BSI 12-1999 iii Foreword This BritishStandard, which has been prepared unde

15、r the direction of the Electronic Components Standards Committee, is the generic specification for custom-built capacitors and capacitor modules in the BS9000 system of standards for electronic parts of assessed quality. A British Standard does not purport to include all the necessary provisions of

16、a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi to iv, pages1to20 and a back cover

17、. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.iv blankBS9100:1983 BSI 12-1999 1 0 Introduction This BritishStandard is the generic specification for custom-built capacitors and c

18、apacitor modules which are not appropriate for assessment under qualification approval for one or more of the following reasons. a) Each type is designed for a particular customer requirement. b) Each type requires an individual specification to satisfy the particular customers needs. c) The custome

19、r requirement cannot be satisfied from a standard range capable of qualification approval. Capacitors in these categories are termed custom-built capacitors. Examples of custom-built capacitors are those having package and/or fixing and termination arrangements peculiar to a particular customers app

20、lication or capacitors requiring a specialized process to achieve a particular customer functional requirement, etc. Section 1. Principles and mandatory procedures 1.1 General matters 1.1.1 Scope. This specification gives details of the general requirements, test procedures and other information rel

21、ating to the capability approval of manufacturers of custom-built capacitive units. The units included in the definition of the capability for which approval is sought may have either a single or multi-capacitor function, as described in1.1.1.1 and1.1.1.2. 1.1.1.1 Custom-built capacitors. This stand

22、ard covers custom-built capacitors of the following types. a) Types performing a single capacitive function and manufactured using one or more capacitive elements (see1.1.3.1) permanently electrically interconnected such that only one pair of lead-outs (see1.1.3.2) is available for circuit connectio

23、n and electrical test purposes. b) Types performing only a capacitive function, even when incorporating any add-on component (see1.1.3.3). 1.1.1.2 Custom-built capacitor modules. This standard covers custom-built capacitor modules of the following types. a) Assemblies of capacitors performing a mult

24、i-capacitive function and manufactured using two or more capacitors or capacitive elements, permanently electrically interconnected such that sufficient lead-outs are available to allow measurement of all specified capacitive functions of the module for circuit connection and electrical test purpose

25、s. b) Types performing only capacitive functions, even when incorporating any add-on component. 1.1.2 Related documents BS1852, (IEC62) Marking codes for resistors and capacitors. BS2011, (IEC68) Environmental testing. BS2045, (ISO3) Preferred numbers. BS2488, (IEC63) Schedule of preferred numbers f

26、or the resistance of resistors and the capacitance of capacitors for telecommunication equipment. BS3939, (IEC617) Graphical symbols for electrical power, telecommunications and electronics diagrams. BS4727, Glossary of electrotechnical, power, telecommunications, electronics, lighting and colour te

27、rms. BS5775, Specification for quantities, units and symbols. BS6001, (ISO2859) Sampling procedures for inspection by attributes Part1: Specification for sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection. BS9000, General requirements for a system for electronic compo

28、nents of assessed quality Part1:Specification of general procedures. BS9070, Specification for fixed capacitors of assessed quality: generic data and methods of test. BS CECC30000, Harmonized system of quality assessment for electronic components. Generic specification:Fixed capacitors. BS CECC30100

29、, Harmonized system of quality assessment for electronic components. Sectional specification: Fixed polyethylene terephthalate film dielectric metal foil capacitors for direct current.BS9100:1983 2 BSI 12-1999 BS CECC30500, Harmonized system of quality assessment for electronic components: Sectional

30、 specification: Fixed metallized polycarbonate film dielectric capacitors for direct current. PD9002, BS9000, IECQ and CECC qualified products list. 1.1.3 Terminology. For the purposes of this BritishStandard, the definitions given in BS4727 apply together with the following. 1.1.3.1 capacitive elem

31、ent. An element that is either: a) a BS9000 or BS CECC qualification approved capacitor; or b) a part-manufactured capacitor falling within the boundaries and technologies of the manufacturers own declared capability approval. 1.1.3.2 lead-outs. Any electrical connections that are available for circ

32、uit connection and electrical test purposes. 1.1.3.3 add-on components. Components other than capacitors that are essential to the customer requirements that do not change the capacitive function of the item. Such components shall be permanently attached to the assembly both mechanically and electri

33、cally. They are acceptable for incorporation only when procured in accordance with 3.3 of BS9000-5:1989. 1.1.4 Letters, symbols, signs and abbreviations. The letters, symbols, signs and abbreviations which are employed in all documents applicable to electronic components covered by this specificatio

34、n shall be in conformity with BS5775 or shall be derived in accordance with the principles of that standard. 1.1.5 Graphical symbols. The graphical symbols which are employed in all documents applicable to electronic components covered by this specification shall be in accordance with BS3939 or shal

35、l be derived in accordance with the principles of that standard. 1.1.6 Marking of the component and package 1.1.6.1 Each custom-built capacitor or capacitor module shall be marked with a) and b) and with as many of the remaining items, in the order given below, as is practicable. a) Polarity (electr

36、olytic capacitors only). b) Rated capacitance and tolerance (these values may be in code form in accordance with BS1852 (IEC62). c) Rated voltage (d.c. and/or a.c.). d) Date code and lot identification (see 4.2 of BS9000-7:1989). e) Manufacturers name or trade mark. f) Number of the detail specifica

37、tion and (where necessary) pattern number. g) Any additional marking required by the detail specification. 1.1.6.2 All the information required by1.1.6.1 shall be marked on the package of the components. NOTEWhere a transparent package is used, the information may be marked on a label which may be r

38、ead without opening the package. 1.1.7 Eligibility for capability approval. The primary stage of manufacture of a capacitor or capacitor module is that at which the primary performance of the capacitor is determined and is defined as: a) the winding of the element of a wound type; b) the stacking of

39、 the plates of a plate type; c) the formation of the oxide layer of an electrolytic type; d) the application of the electrodes to a single layer dielectric capacitor plate, disc, tube or similar construction. NOTEThe requirements of 3.3.5 of BS9000-5:1989 do not apply to custom-built capacitive elem

40、ents, capacitors or capacitor modules. 1.1.8 Delayed delivery. The period following manufacturers acceptance inspection, after which reinspection to group A is required, shall be as follows. a) Aluminium electrolytic capacitors (all types):12months. b) All other capacitors of climatic category-/-/04

41、 and-/-/A4: 12months. c) All other capacitors of any type or climatic category:24months. NOTEAt the discretion of the manufacturer, aluminium electrolytic capacitors may be subjected to conditioning in accordance with the requirements of the relevant sectional specification prior to retesting to gro

42、up A inspection.BS9100:1983 BSI 12-1999 3 1.1.9 Certified test records. Not applicable. 1.1.10 Preferred climatic categories. The custom-built capacitors and capacitor modules covered by this document are classified into climatic categories according to the general rules given in BS2011 and should b

43、e selected from the following preferred climatic categories: 1.1.11 Unchecked parameters. Unchecked parameters are not used for inspection purposes and consistent performance under such conditions cannot be relied upon. 1.1.12 Ordering information. See customer detail specification. 1.1.13 Release p

44、rior to completion of group B tests. Not applicable. 1.1.14 Supplementary procedures for reduced inspection. The procedures of 9.3.3 of BS6001-1:1991 are applicable. 1.1.15 Rectification. Rework shall only be permitted within the procedures declared in the manufacturers approved capability manual. S

45、uch procedures have to demonstrate, to the satisfaction of the supervising inspectorate, that the subsequent reliability of the component as supplied to the customer is not thereby impaired. 1.2 Test procedures Test methods shall be selected from BS9000 series or CECC specifications. 1.3 Capability

46、approval and maintenance procedures A manufacturer wishing to supply custom-built capacitors and capacitor modules in accordance with this standard is required: a) to conform to the provision and requirements of clause2 of BS9000-4:1989. b) to obtain approval of his production capability using a dec

47、lared technology in accordance with the procedures and requirements given in clause3 of BS9000-6:1989, together with the following: 1) description of capability: capability manual; 2) programme for capability assessment; 3) performance for capability assessment programme; 4) abstract of description

48、of capability for publication in PD 9002; 5) capability approval report; 6) quality conformance inspection. 1.3.1 Description of capability. Manufacturers shall describe the scope and extent of their capability by means of a capability manual compiled in accordance with clause 3 of BS9000-6:1989 and

49、 as required in the sectional specifications. Each manufacturer seeking approval is required to declare the scope of his application in terms of the items shown in Figure 1. 1.3.2 Programme for capability approval. The manufacturer shall prepare a programme for the assessment of the declared capability to the satisfaction of the National Supervising Inspectorate (NSI). This programme shall be so designed that all the declared boundary conditions and range of products of the capability will be assessed and shall include the following: a) details of the capabi