BS 9000-1-1989 General requirements for a system for electronic components of assessed quality - Specification of general procedures《电子元器件质量评定体系的一般要求 通用程序规范》.pdf
《BS 9000-1-1989 General requirements for a system for electronic components of assessed quality - Specification of general procedures《电子元器件质量评定体系的一般要求 通用程序规范》.pdf》由会员分享,可在线阅读,更多相关《BS 9000-1-1989 General requirements for a system for electronic components of assessed quality - Specification of general procedures《电子元器件质量评定体系的一般要求 通用程序规范》.pdf(22页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS 9000-1: 1989 General requirements for a system for electronic components of assessed quality Part 1: Specification of general procedures UDC 621.37/.39:658.562.64BS 9000-1:1989 This British Standard, having been prepared under the directionof the Electronic Components Standards P
2、olicyCommittee, was publishedunder the authority ofthe Board of BSI and comesintoeffect on 31 October 1989 BSI 02-1999 First published May 1967 First revision July 1971 Second revision December 1981 Third revision October 1989 The following BSI references relate to the work on this standard: Committ
3、ee reference ECL/- Draft for comment 88/30354 DC ISBN 0 580 17704 1 Committees responsible for this British Standard This British Standard was prepared by the Electronic Components Standards Policy Committee (ECL/-), upon which the following bodies were represented: BEAMA Ltd. British Standards Soci
4、ety British Telecommunications plc Department of Trade and Industry (Electronics Applications Division) Electronic Components Industry Federation Electronic Engineering Association Institution of Electrical Engineers Ministry of Defence National Supervising Inspectorate Society of British Aerospace
5、Companies Limited Telecommunication Engineering and Manufacturing Association (TEMA) Amendments issued since publication Amd. No. Date of issue CommentsBS9000-1:1989 BSI 02-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Definitions 1 3 The BS 9000 system and i
6、ts operation 5 4 Appeals procedure 7 5 The specification system 7 6 Procedures for detail specifications 9 7 Authority of documents 11 Appendix A Cross-reference to BS 9000-1:1981 14 Figure 1 BS 9000 mark: master symbols for photographic reproduction 12 Figure 2 BS 9000 mark: proportional dimensions
7、 13 Table 1 Cross-reference to BS 9000-1:1981 14 Publications referred to Inside back coverBS9000-1:1989 ii BSI 02-1999 Foreword This Part of BS9000 has been prepared under the direction of the Electronic Components Standards Policy Committee (ECL/-). It forms part of a revision of BS9000-1:1981and
8、BS9005:1985, both of which are now withdrawn. The revision comprises a vital and necessary restructuring of these standards couples with the incorporation of text from BS9000-2:1972 and from various circular letters from PD9004. The restructuring has resulted in BS9000-1:1981 and BS9005:1985being re
9、placed by the following publications. Part 1: Specification of general procedures; Part 4: Specification of procedures for the approval of an organization; Part 5: Specification of qualification approval and conformance testing procedures; Part 6: Specification of capability approval procedures; Par
10、t 7: Specification of lot formation, release procedures and certified test records; Part 8: Drafting requirements; Section 8.1: Generic, sectional and blank detail specifications produced under qualification approval; Section 8.2: Generic and sectional specifications produced under capability approv
11、al. NOTEA cross-reference between BS9000-1:1981 and this revision is given in Appendix A. These publications describe, and specify, the BS9000system. They are not intended to apply to the United Kingdom implementation of either the CECC 1)or IECQ 2)systems. It has been decided, after considering the
12、 implications of the intended completion of the Internal Market by December1992, that a complete “stand alone” publication describing and specifying the UK implementation of the CECC system is needed. A similar “stand alone” publication for the UK implementation of the IECQ system is also envisaged.
13、 BS9000-2and BS9000-3will be revised to implement these decisions. This revision of BS9000-1:1981gives a more complete description of the requirements for capability approval and for the drafting of specifications. The revision will be applied to all approval exercises and to all generic, sectional
14、and blank detail specifications drafted after the date of its publication. The requirements contained in the revision will also apply to the revision of existing BS9000standards. BS9000-4 specifies procedures for the approval of organizations. It is intended that the appropriate Part of BS5750be inv
15、oked in due course as a requirement for approval. It should be noted that BS9000-4 contains requirements specific to the System 3)not covered by BS5750. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their cor
16、rect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 to 16, an inside back cover and a back cover. This standard has been updated (see copy
17、right date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover. 1) CENELEC Electronic Components Committee (System for Europe). 2) IEC Quality Assessment System for Electronic Components. 3) For definition of “the System”, see2.1.1.BS9000
18、-1:1989 BSI 02-1999 1 1 Scope This Part of BS9000specifies the general procedures for the BS9000system for the specification, qualification or capability approval, inspection and release of electronic components of assessed quality. The BS9000system operates in the United Kingdom, defined for this p
19、urpose as England, Scotland, Wales, Northern Ireland, the Isle of Man and the Channel Islands. It can be extended to any other member country of the CECC by mutual agreement of the National Authorized Institutions concerned. NOTEThe titles of the publications referred to in this standard are listed
20、on the inside back cover. 2 Definitions For the purposes of this British Standard the following definitions apply. 2.1 Definitions related to the System 2.1.1 the System the totality of functions, activities, documents and definitions in BS9000-1 and BS9000-4 to BS9000-8 2.1.2 the Mark the BS9000Cer
21、tification Trade Mark owned by BSI and registered under the Trade Marks Act1938under number12 50 774in class9in respect of the BS9000series of British Standard specifications for electronic components of assessed quality 2.1.3 qualified products list (QPL) a list maintained by BSI and published as P
22、D9002, of components, organizations and technologies approved under the System 2.1.4 administrative guide the document published by BSI as PD9004and entitled “BS9000, CECC and IECQ UK Administrative Guide” 2.1.5 circular letter (CL) a means of communicating changes or additions to the System prior t
23、o permanent revision, or administrative procedures as a supplement to the System 2.1.6 National Supervising Inspectorate (NSI) the authority responsible for conducting the appraisal and surveillance of the requirements of the System 2.2 Definitions related to specifications 2.2.1 basic specification
24、 a specification applicable to all electronic components or to a large group of electronic components (e.g.BS9000, BS6001, BS2011) 2.2.2 generic specification a specification applicable to a family or sub-family of electronic components 2.2.3 sectional specification a specification applicable to a s
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS900011989GENERALREQUIREMENTSFORASYSTEMFORELECTRONICCOMPONENTSOFASSESSEDQUALITYSPECIFICATIONOFGENERALPROCEDURES
链接地址:http://www.mydoc123.com/p-547587.html