BS 7F 34-2002 Light and medium duty linen (flax) sewing thread for aerospace purposes《航天航空用轻型和中型亚麻缝纫线》.pdf

《BS 7F 34-2002 Light and medium duty linen (flax) sewing thread for aerospace purposes《航天航空用轻型和中型亚麻缝纫线》.pdf》由会员分享，可在线阅读，更多相关《BS 7F 34-2002 Light and medium duty linen (flax) sewing thread for aerospace purposes《航天航空用轻型和中型亚麻缝纫线》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS 7F 34:2002 (Superseding BS 6F 34:1984) Light and medium duty linen (flax) sewing thread for aerospace purposes ICS 49.025.60 BS 7F 34:2002 This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was

2、 published under the authority of the Sector Policy and Strategy Committee 17 October 2002 BSI 17 October 2002 First published BS F 34:1919 Second edition BS 2F 34:1930 Third edition BS 3F 34:1934 Fourth edition BS 4F 34:1960 Fifth edition BS 5F 34:1975 Sixth edition BS 6F 34:1984 Seventh edition BS

3、 7F 34:2002 The following BSI references relate to the work on this standard: Draft for comment 00/707766 DC Committee reference ACE/22 ISNB 0 580 36951 X Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/22, Cords, rop

4、es and threads for aerospace purposes, upon which the following bodies were represented: Linen Sewing Threads Manufacturers Association Ministry of Defence UK Defence Standardization Society of British Aerospace Companies Ltd. Amendments issued since publication Amd. No. Date CommentsBS 7F 34:2002 B

5、SI 17 October 2002 i Contents Page Committees responsible Inside front cover Foreword ii 1S c o p e 1 2 Normative references 1 3G e n e r a l 1 4Y a r n 2 5 Finish 2 6 Construction and properties 3 7 Identification 3 Bibliography 5 Table 1 General requirements (given in BS F 100) 1 Table 2 Construct

6、ion and properties 3BS 7F 34:2002 ii BSI 17 October 2002 Foreword This British Standard, prepared under the direction of Technical Committee ACE/22, is one of a series for textiles of a quality suitable for aerospace purposes. It supersedes BS 6F 34:1984 which is withdrawn. NOTE The previous edition

7、, BS 6F 34:1984, deleted rotproofing by the copper chrome process and required that all thread be supplied rotproofed by the pentachlorophenyl laurate (PCPL) process. This new edition incorporates all earlier amendments, updates references and improves nomenclature in line with other standards in th

8、e same series. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. WARNING NOTES This standard calls for the use of su

9、bstances and/or test procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and in no way absolves either the supplier or the user from statutory obligations relating to health and safety at any stage of manufacture or use. This stan

10、dard specifies pentachlorophenyl laurate (PCPL) as the only approved rotproofing treatment for aerospace textiles. Alternative treatments are under development, and this standard will be updated to delete PCPL as soon as an approved alternative treatment for aerospace textiles is available. Summary

11、of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.BS 7F 34:2002 BSI 17 October 2002 1 1 Scope This British Standard specifies the requir

12、ements for light and medium duty linen sewing thread for aerospace purposes. NOTE The latest revision of an Aerospace Series standard is indicated by a prefix number. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated reference

13、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. BS 2087-1, Preservative treatments for textiles Specification for treatments. BS F 100, Procedure for inspection and testing of textiles for aerospace purposes

14、. BS EN ISO 2060:1995, Textiles Yarn from packages Determination of linear density (mass per unit length) by the skein method. BS EN ISO 2061, Textiles Determination of twist in yarn Direct counting method. 3 General 3.1 In addition to the requirements specified in Clause 4, Clause 5, Clause 6 and C

15、lause 7 of this standard the requirements and tests given in the latest edition of BS F 100 as specified in Table 1, shall apply. Table 1 General requirements (given in BS F 100) 3.2 Freedom from faults Threads shall have uniformity of thickness, construction, and component ply tension so that there

16、 are no visually irregular twist faults. Threads of length per unit mass less than 6 000 m/kg shall contain no thread knots. Threads of length per unit mass greater than 6 000 m/kg shall not contain more than two thread knots per package. 3.3 Length per unit mass The length per unit mass of thread s

17、hall be determined in accordance with BS EN ISO 2060:1995, Option 1. Section of BS F 100 Section title Requirements and tests 1 General All requirements 2 a Quality requirements Requirements for dyed textiles except those related to fabric intended for coating Requirements for freedom from corrosive

18、 impurities (see BS F 100, Section 4) 3 Physical tests Tests for breaking strength and extension under force 4 Chemical tests Test for residual alkali solubility If required by BS F 100, Section 2: test for conductivity of aqueous extract; test for pH value of aqueous extract; test for water soluble

19、 chloride; test for water soluble sulfate. a It is not intended that BS F 100, Section 2 tests should be performed on each thread batch. The frequency of these tests should be agreed between the Quality Assurance Authority and the thread manufacturer, BS F 100.BS 7F 34:2002 2 BSI 17 October 2002 4 Y

20、arn 4.1 The thread shall be manufactured from flax fibre (Linum usitatissimum) in a three-fold construction. 4.2 The mass of the yarn shall have been reduced by not less than 10 %, by boiling. NOTE The degree of boiling of the yarn should be determined from the manufacturers records, if available. O

21、therwise, the residual alkali solubility of the thread should be determined and should not exceed 10 %. 5 Finish 5.1 Condition of material The thread shall be supplied in one of the following conditions: a) undyed and rotproofed; b) undyed, rotproofed and wax finished; c) dyed and rotproofed; or d)

22、dyed, rotproofed and wax finished. 5.2 Dyeing Where dyeing is required, the colour shall be specified by reference to an official standard, e.g. BS 381C, or otherwise by pattern. NOTE Reference to an official standard, e.g. BS 381C is preferable. 5.3 Rotproofing The thread shall be treated with pent

23、achlorophenyl laurate (PCPL) from aqueous emulsion in accordance with BS 2087-1, normal process. 5.4 Wax finishing Where wax finishing is required, beeswax substitute microcrystalline hydrocarbon wax shall be used and the added mass due to the wax shall be (20 5) %. Prior to waxing, the thread shall

24、 have been rotproofed in accordance with 5.3. 5.5 Surface finish The thread supplied in accordance with 5.1a) and 5.1c) shall be polished, but substances which promote microbiological growth (e.g. starch or modified starch) shall not be applied.BS 7F 34:2002 BSI 17 October 2002 3 6 Construction and

25、properties 6.1 The thread shall conform to the requirements given in Table 2. Table 2 Construction and properties 6.2 The direction of final twist shall be Z. 7 Identification The thread shall be identified by the following: a) the number of this British Standard, i.e. BS 7F 34; b) the relevant desi

26、gnation number given in Table 2; c) the finish; d) the colour (where required). NOTE This identification may be codified. For example, thread No. 12 required dyed black and waxed may be identified as “BS 7F 34/No. 12/black/waxed”. Designation Nominal resultant linear density Final twist a Length per

27、 unit mass b Minimum average breaking strength unwaxed waxed tex Turns/m m/kg N N No. 12 420 275 40 2 400 5 % 110 89 No. 18 275 355 40 3 650 5 % 71 57 No. 25 200 435 40 5 050 5 % 53 43 No. 30 170 470 40 6 050 5 % 45 36 No. 35 145 510 40 7 050 5 % 36 28 No. 40 125 550 40 8 050 5 % 31 25 No. 50 100 59

28、0 40 10 100 5 % 27 21 No. 60 84 630 40 12 100 5 % 22 18 No. 70 71 690 60 14 100 5 % 16 No. 80 63 730 60 16 100 5 % 13 a The final twist shall be determined in accordance with BS EN ISO 2061. b The length per unit mass shall be determined by weighing a skein conditioned and reeled in accordance with

29、BS EN ISO 2060:1995, Option 1. The values stated for length per unit mass exclude the mass of added dye and/or finishes.4 blankBS 7F 34:2002 BSI 17 October 2002 5 Bibliography Standards publications BS 381C:1996, Specification for colours for identification, coding and special purposes.BS 7F 34:2002

30、 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standard

31、s are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using th

32、is British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automa

33、tically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website a

34、t http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and inter

35、national standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.

36、 Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Info

37、rmation regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publ

38、ications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written per

39、mission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.