BS 7670-1-1993 Steel nuts and bolts for resistance projection welding - Specification for dimensions and properties《电阻凸焊用钢螺母和螺栓 第1部分 尺寸和性能规范》.pdf

《BS 7670-1-1993 Steel nuts and bolts for resistance projection welding - Specification for dimensions and properties《电阻凸焊用钢螺母和螺栓 第1部分 尺寸和性能规范》.pdf》由会员分享，可在线阅读，更多相关《BS 7670-1-1993 Steel nuts and bolts for resistance projection welding - Specification for dimensions and properties《电阻凸焊用钢螺母和螺栓 第1部分 尺寸和性能规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 7670-1: 1993 Incorporating Amendment No. 1 Steel nuts and bolts for resistance projection welding Part 1: Specification for dimensions and properties UDC 621.882:669.14.018:621.791.76BS7670-1:1993 This British Standard, having been prepared under the direction of the General Mech

2、anical Engineering Standards Policy Committee, was published under the authority of the Standards Board and comes into effecton 15September1993 BSI 01-1999 The following BSI references relate to the work on this standard: Committee reference GME/9 Draft for comment 92/82393 DC ISBN 0 580 21856 2 Com

3、mittees responsible for this British Standard The preparation of this British Standard was entrusted by the General Mechanical Engineering Standards Policy Committee (GME/-) to Technical Committee GME/9, upon which the following bodies were represented: BEAMA Ltd. British Constructional Steelwork As

4、sociation Ltd. British Industrial Fasteners Federation British Railways Board British Steel Industry British Steel Industry (Wire Section) Gauge and Tool Makers Association Society of Motor Manufacturers and Traders Ltd. Washer Manufacturers Association of Great Britain The following bodies were als

5、o represented in the drafting of the standard, through subcommittees and panels: Defence Manufacturers Association General Municipal Boilermaker and Allied Trades Union Screw Thread Tool Manufacturers Association Society of British Aerospace Companies Ltd. Amendments issued since publication Amd. No

6、. Date Comments 8215 July 1994 Indicated by a sideline in the marginBS7670-1:1993 BSI 01-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 References 1 3 Definitions 1 4 Weld bolts 1 5 Weld nuts 1 Figure 1 Dimensions of weld bolts 2 Figure 2 Dimensions of square

7、weld nuts 3 Figure 3 Dimensions of hexagonal weld nuts 4 Table 1 Dimensions of weld bolts 2 Table 2 Characteristics of weld bolts 3 Table 3 Dimensions of square weld nuts 4 Table 4 Dimensions of hexagonal weld nuts 5 Table 5 Characteristics of weld nuts 5 List of references Inside back coverBS7670-1

8、:1993 ii BSI 01-1999 Foreword This Part of BS7670 has been prepared under the authority of the General Mechanical Engineering Standards Policy Committee. It is one Part of a standard for steel nuts and bolts for resistance projection welding. BS 7670-2 provides a specification for the welding proces

9、ses and conditions applicable to weld bolts and nuts for resistance projection welding. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of

10、itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be

11、 indicated in the amendment table on theinside front cover.BS7670-1:1993 BSI 01-1999 1 1 Scope This Part of BS 7670 specifies the general dimensions, tolerances, materials and mechanical properties both for imperial weld nuts threaded7/1620UNF2B and metric weld nuts and weld bolts with nominal threa

12、d diameters from M3toM12inclusive. The weld bolts have circular heads with three projections and the nuts are square with four projections or hexagonal with three projections for projection welding. 2 References 2.1 Normative references This Part of BS7670 incorporates, by reference, provisions from

13、 specific editions of other publications. These normative references are cited at the appropriate points in the text and the publications are listed on the inside back cover. Subsequent amendments to, or revisions of, any of these publications apply to this Part of BS7670 only when incorporated in i

14、t by updating or revision. 2.2 Informative references This Part of BS7670 refers to other publications that provide information or guidance. Editions of these publications current at the time of issue of this standard are listed on the inside back cover, but reference should be made to the latest ed

15、itions. 3 Definitions For the purposes of this Part of BS 7670, the definitions given in BS 499-1:1991 apply. 4 Weld bolts 4.1 Dimensions The dimensions of weld bolts shall be as given inFigure 1 andTable 1. The electrode contact area d f min. shall be flat, smooth and free from surface projections.

16、 4.2 Characteristics The materials, tolerances and mechanical properties shall be as given inTable 2. 4.3 Designation When designating weld bolts for the purpose of an enquiry or order, the following information shall be given: a) general product description, i.e.weld bolt; b) the number of this Bri

17、tish Standard, i.e.BS7670-1; c) the letter M indicating that the product is ISOmetric; d) the nominal size (thread diameter) of the product in millimetres (d inFigure 1); e) the nominal length in millimetres (l in Figure 1); f) the property class; g) details of the coating (if required) and the rele

18、vant British Standard where applicable. Example. The designation of a weld bolt, with a thread diameter of 8mm, and a nominal length of25mm, conforming to class4.8, is as follows: Weld bolt BS7670-1, M8 25 4.8 5 Weld nuts 5.1 Dimensions The dimensions of square weld nuts shall be as given inFigure 2

19、 andTable 3. The dimensions of hexagonal weld nuts shall be as given inFigure 3 andTable 4. 5.2 Characteristics The materials, tolerances and mechanical properties shall be as given inTable 5.BS7670-1:1993 2 BSI 01-1999 Table 1 Dimensions of weld bolts NOTEDimension l is the designated nominal lengt

20、h (see 4.3). Figure 1 Dimensions of weld bolts Dimensions in millimetres Thread size, d M3 M4 M5 M6 M8 M10 M12 Thread pitch 0.5 0.7 0.8 1.0 1.25 1.5 1.75 a max. 1.25 1.75 2.0 2.5 3.13 3.75 4.38 d k max. 6.37 8.45 10.45 12.55 16.55 20.65 24.65 min. 5.63 7.55 9.55 11.45 15.45 19.35 23.35 d f min. 5.13

21、 7.05 9.05 10.95 14.95 18.85 22.85 d 1 max. 4.98 6.48 8.08 9.58 12.70 15.70 18.70 min. 4.50 6.00 7.50 9.00 12.00 15.00 18.00 d 2 max. 1.15 1.45 1.75 2.05 2.65 3.25 3.90 min. 0.90 1.20 1.50 1.80 2.40 3.00 3.60 V max. 0.55 0.70 0.85 1.00 1.30 1.60 1.90 min. 0.35 0.50 0.65 0.80 1.10 1.40 1.70 k max. 1.

22、32 1.72 2.12 2.52 3.35 4.15 4.95 min. 1.07 1.47 1.87 2.27 3.05 3.85 4.65 r max. 0.40 0.40 0.50 0.60 0.80 0.80 0.80 NOTETolerances conform to BS6322-1:1982.BS7670-1:1993 BSI 01-1999 3 Table 2 Characteristics of weld bolts Characteristic Requirement Material Steel with a carbon content not greater tha

23、n0.23% Thread tolerance Conforming to class 6g of BS3643-1:1981 and BS 3643-2:1981 Mechanical properties a Conforming to material property class4.8,5.8 or8.8 of BSEN 20898-1:1992, test programme B b Permissible dimensional deviations and deviations of form Conforming to product grade A of BS6322-1:1

24、982 Finish As processed, with a lubricant, but free from scale and excessive oxide, as rolled, unless otherwise agreed between the purchaser and supplier c Acceptability In accordance with BS6587:1985 a Both before and after welding. b The material property class shall be marked on the bolts by the

25、indented method only. c Alternative surface finishes (e.g.electroplating) may be applied, if agreed between the purchaser and supplier. Some surface finishes are unsuitable for welding. NOTEThe internal form of the weld projections may be radiused at the discretion of the supplier. Figure 2 Dimensio

26、ns of square weld nutsBS7670-1:1993 4 BSI 01-1999 Table 3 Dimensions of square weld nuts NOTEThe internal form of the weld projections may be radiused at the discretion of the supplier. Figure 3 Dimensions of hexagonal weld nuts Dimensions in millimetres Thread size, d 1 M4 M5 M6 M8 M10 20UNF2B M12

27、Thread pitch 0.7 0.8 1.0 1.25 1.5 1.75 b max. 0.95 1.15 1.35 1.65 2.0 2.2 2.2 min. 0.65 0.85 1.05 1.35 1.6 1.8 1.8 d 2 max. 5.18 6.18 7.72 10.22 12.77 13.77 13.77 min. 5 6 7.5 10 12.5 13.5 13.5 d 3 max. 4.2 5.25 6.3 8.4 10.5 11.7 12.6 e min. 9 12 13 18 22 25 25 h max. 0.7 0.9 0.9 1.1 1.3 1.5 1.5 min

28、. 0.5 0.7 0.7 0.9 1.1 1.3 1.3 m max. 3.5 4.2 5 6.5 8 9 9.5 min. 3.2 3.9 4.7 6.14 7.64 8.64 9.14 s max. 7 9 10 14 17 19 19 min. 6.64 8.64 9.64 13.57 16.57 18.48 18.48 7 16 -BS7670-1:1993 BSI 01-1999 5 Table 4 Dimensions of hexagonal weld nuts Table 5 Characteristics of weld nuts Dimensions in millime

29、tres Thread size, d 1 M3 M4 M5 M6 M8 M10 20 UNF2B M12 Thread pitch 0.5 0.7 0.8 1.0 1.25 1.5 1.75 b max. 1.0 1.0 1.0 1.12 1.25 1.55 1.55 1.55 min. 0.6 0.6 0.6 0.68 0.75 0.95 0.95 0.95 d 2 max 4.68 6.18 7.22 8.22 10.77 12.77 13.77 15.07 min. 4.5 6 7 8 10.5 12.5 13.5 14.8 d 3 max. 3.15 4.2 5.25 6.3 8.4

30、 10.5 11.7 12.6 d 4 max. 4.47 5.97 6.96 7.96 10.45 12.45 13.45 14.75 min. 4.395 5.895 6.87 7.87 10.34 12.34 13.34 14.64 e min. 8.15 9.83 10.95 12.02 15.38 18.74 20.91 20.91 h 1 max. 0.55 0.65 0.7 0.75 0.9 1.15 1.4 1.4 min. 0.45 0.55 0.6 0.6 0.75 1 1.2 1.2 h 2 max. 0.25 0.35 0.4 0.4 0.5 0.65 0.8 0.8

31、min. 0.15 0.25 0.3 0.3 0.35 0.5 0.6 0.6 m max. 3 3.5 4 5 6.5 8 10 10 min. 2.75 3.2 3.7 4.7 6.14 7.64 9.64 9.64 s max. 7.5 9 10 11 14 17 19 19 min. 7.28 8.78 9.78 10.73 13.73 16.73 18.67 18.67 Characteristic Requirement Material Steel with a carbon content not greater than 0.23% Thread tolerance ISO

32、metric Conforming to class 6H of BS 3643-1:1981 and BS 3643-2:1981 Unified Conforming to class 2B of BS1580-1:1962 b) the number of this British Standard, i.e.BS7670-1; c) the letter M indicating that the product is ISOmetric; d) the nominal size (thread diameter) of the product in millimetres; e) t

33、he property class; f) details of the coating (if required) and the relevant British Standard where applicable. Example. The designation of a square weld nut with a thread diameter of8mm, conforming to property class6, is as follows: Square weld nut BS 7670-1, M86. 5.3.2 20 UNF 2B weld nuts When desi

34、gnating 20 UNF 2B weld nuts for the purpose of an enquiry or order, the following information shall be given: a) general product description, e.g.hexagonal weld nut; b) the number of this British Standard, i.e.BS7670-1; c) the thread size, i.e. 20 UNF 2B; d) the property class; e) details of the coa

35、ting (if required) and the relevant British Standard where applicable. Example. The designation of a hexagonal weld nut with a 20 UNF 2B thread, conforming to property class 4, is as follows: Hexagonal weld nut BS 7670-1, 20UNF 2B 4. 7 16 - 7 16 - 7 16 - 7 16 - 7 16 -BS7670-1:1993 BSI 01-1999 List o

36、f references (see clause2) Normative references BSI standards publications BRITISH STANDARDS INSTITUTION, London BS 499, Welding terms and symbols. BS 499-1:1991, Glossary for welding, brazing and thermal cutting. BS 1580, Specification for Unified screw threads. BS 1580-1:1962 & BS 1580-2:1962, Dia

37、meters in and larger. BS 3643, ISO metric screw threads. BS 3643-1:1981, Principles and basic data. BS 3643-2:1981, Specification for selected limits of size. BS 6322, Tolerances for fasteners. BS 6322-1:1982, Specification for tolerances of bolts, screws and nuts with thread diameters$ 1.6mmand# 15

38、0mm and product grades A, B and C. BS 6587:1985, Method of acceptance inspection for fasteners. BS EN 20898, Mechanical properties of fasteners. BS EN 20898-1:1992, Bolts, screws and studs. BS EN 20898-2:1992, Nuts with specified proof load values. Informative references BSI standards publications B

39、RITISH STANDARDS INSTITUTION, London BS 7670, Steel nuts and bolts for resistance projection welding. BS 7670-2, Welding conditions 1)2) . 1) In preparation. 2) Referred to in foreword only. 1 4 -BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

40、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Stan

41、dards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the cons

42、tant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Te

43、l: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Cust

44、omer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of inform

45、ation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 89

46、96 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in

47、 all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means

48、 electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.