BS 7655-3 2-2000 Specification for insulating and sheathing materials for cables - PVC insulating compounds - Hard grade types - Hard grade types《电缆用绝缘和铠装材料规范 PVC绝缘化合物 硬等级型》.pdf

《BS 7655-3 2-2000 Specification for insulating and sheathing materials for cables - PVC insulating compounds - Hard grade types - Hard grade types《电缆用绝缘和铠装材料规范 PVC绝缘化合物 硬等级型》.pdf》由会员分享，可在线阅读，更多相关《BS 7655-3 2-2000 Specification for insulating and sheathing materials for cables - PVC insulating compounds - Hard grade types - Hard grade types《电缆用绝缘和铠装材料规范 PVC绝缘化合物 硬等级型》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS 7655-3.2:2000 ICS 29.0

2、35.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Specification for Insulating and sheathing materials for cables Part 3: PVC insulating compounds Section 3.2: Hard grade types IMPORTANT NOTE This section of BS 7655 is to be read in conjunction with BS 7655-0.This British

3、Standard, having been prepared under the direction of the Electrotechnical Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 November 2000 BSI 11-2000 First published April 1993 Second edition November 2000 The following BSI references relate

4、to the work on this standard: Committee reference GEL/20/3 Draft for comment 99/240495 DC ISBN 0 580 33196 2 BS 7655-3.2:2000 Amendments issued since publication Amd. No. Date Comments Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technica

5、l Committee GEL/20, Electric cables, to Subcommittee GEL/20/3, Insulation and sheath, upon which the following bodies were represented: Association of Consulting Engineers British Approvals Service for Cables British Cables Association British Plastics Federation British Rubber Manufacturers Associa

6、tion Ltd. Department of Trade and Industry (Consumer Safety Unit, CA Division) Electricity Association ERA Technology Ltd. GAMBICA (BEAMA Ltd.) Institute of Fire Prevention Officers London Underground Ltd. Ministry of Defence Queen Mary and Westfield College Railtrack Warrington Fire Research Centre

7、BS 7655-3.2:2000 BSI 11-2000 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Normative references 1 3 Definitions 1 4 Requirements 1 Bibliography 3ii BSI 11-2000 BS 7655-3.2:2000 Foreword This section of BS 7655 has been prepared by Subcommittee GEL/20/3. It superse

8、des BS 7655-3.2:1993 which is withdrawn. It specifies the requirements for hard grade PVC insulating compound type 2. This revision brings this section of BS 7655 fully into line with BS 7655-0:1997, including amendment 1:2000. Test methods are specified in this section of BS 7655 by reference to th

9、e latest edition of standards in which they appear. A dated reference to the most recent edition of the relevant standard for each test method is given in BS 7655-0, which is to be read in conjunction with this section. A British Standard does not purport to include all the necessary provisions of a

10、 contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 3 and a back co

11、ver. The BSI copyright notice displayed in this document indicates when the document was last issued.BS 7655-3.2:2000 BSI 11-2000 1 1 Scope This section of BS 7655 specifies the requirements for the hard grade PVC insulating compound listed in Table 1. The relevant test methods are given in BS EN 60

12、811 and BS 6469. This section is to be read in conjunction with BS 7655-0, which contains essential provisions for the application of this section of BS 7655. Table 1 Type of hard grade PVC insulation Type Maximum material operating temperature General application 8C 2 70 Hard grade 2 Normative refe

13、rences For the purposes of this section of BS 7655, the requirements of BS 7655-0, 2.1 apply with regard to normative references. The latest editions of the standards giving test methods are listed in the most recent edition of BS 7655-0. 3 Definitions For the purposes of this section of BS 7655 the

14、 definitions given in BS 7655-0, clause 3 apply together with the following. 3.1 PVC combinations of materials, of which polyvinyl chloride is the characteristic constituent, suitably selected, proportioned and treated, which meet the requirements given in the particular specification 4 Requirements

15、 The requirements specified for the compound listed in Table 2 shall be met when the compound is tested using the test methods listed against each particular requirement. NOTE For cross-references to the latest editions of the test method standards see BS 7655-0, Table 2.2 BSI 11-2000 BS 7655-3.2:20

16、00 Table 2 Test requirements Test Test method in accordance with BS EN 60811 unless otherwise stated Requirements for compound type 2 Section Clause Properties in the state as manufactured 1-1 9.1 Minimum tensile strength (N/mm 2 ) 18.5 Minimum elongation at break (%) 125 Bending test at low tempera

17、ture 1-4 8.1 Temperature (8C) 215 2 Requirement no cracks Elongation test at low temperature 1-4 8.3 Temperature (8C) 215 2 Minimum elongation without break (%) 20 Pressure test at high temperature 3-1 8.1 Temperature (8C) 80 2 Maximum indentation (%) 50 Resistance to cracking 3-1 9.1 Temperature (8

18、C) 150 2 Requirement no cracks Loss of mass test 3-2 8.1 Temperature (8C) 80 2 Duration (h) 73 24 Maximum loss of mass (mg/cm 2 )2 Hot deformation test 1) BS 6469-99.1, clause 10 Maximum deformation (%) 30 Insulation resistance constant BS 6469-99.2, clause 8 Temperature (8C) 20 2 Minimum K value (M

19、V km) 350 1) Only for specified radial thicknesses less than 0.4 mm. BSI 11-2000 3 BS 7655-3.2:2000 Bibliography See BS 7655-0, 2.2.BS 7655-3.2:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

20、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in

21、Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our p

22、roducts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offer

23、s members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 899

24、6 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international s

25、tandards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up

26、 to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyr

27、ight, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwi

28、se without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.