BS 7368-1990 Specification for babies elastomeric feeding bottle teats《婴儿用奶瓶橡皮奶头规范》.pdf

《BS 7368-1990 Specification for babies elastomeric feeding bottle teats《婴儿用奶瓶橡皮奶头规范》.pdf》由会员分享，可在线阅读，更多相关《BS 7368-1990 Specification for babies elastomeric feeding bottle teats《婴儿用奶瓶橡皮奶头规范》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 7368:1990 Specification for Babies elastomeric feeding bottle teatsBS 7368:1990 This British Standard, having been prepared under the directionof the Consumer and Contract Goods Standards Policy Committee, was published under the authority of the Board of BSI and comes into effec

2、t on 30 September 1990 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference CCM/42 Draft for comment 89/47216 DC ISBN 0 580 18967 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Consumer and

3、 Contract Goods Standards Policy Committee (CCM/-) to Technical Committee CCM/42, upon which the following bodies were represented: Association for Consumer Research (ACRE) Association of Public Analysts British Paediatric Association British Retailers Association British Rubber Manufacturers Associ

4、ation Child Accident Prevention Trust Consumer Policy Committee of BSI Department of Health Department of Trade and Industry (Laboratory of the Government Chemist) Department of Trade and Industry (Consumer Safety Unit, CA Division) Health Visitors Association Ice (Ergonomics) Infant and Dietetic Fo

5、ods Association Institute of Trading Standards Administration Malaysian Rubber Producers Research Association Royal College of Nursing Royal Society for the Prevention of Accidents Society of Public Health Amendments issued since publication Amd. No. Date CommentsBS 7368:1990 BSI 09-1999 i Contents

6、Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Definitions 1 3 Materials 1 4 Requirements for individual features 1 5 Performance of the teat 2 6 Packaging 2 7 Marking 2 Appendix A Methods of test for performance of the teat 3 Figure 1 Designation of individual features of a

7、teat 1 Figure 2 Jaws for bite test 4 Publication(s) referred to Inside back coverBS 7368:1990 ii BSI 09-1999 Foreword This British Standard has been prepared under the direction of the Consumer and Contract Goods Standards Policy Committee. Where appropriate, relevant sections of BS5239 have been ad

8、opted, viz. requirements for resistance to bite and for the limitation of the presence of nitrosamines. Requirements for puncture and tear resistance were considered inappropriate for feeding teats which are for use with adult supervision and not designed to take the place of a dummy. Requirements f

9、or maximum permissible levels of certain soluble metals or their compounds have been aligned with those in BS5665-3 which is identical to Part3 of the European Standard EN71. The presence of undesirable plasticizers in plastics has been considered but at present there is insufficient information ava

10、ilable on the toxicity of many plasticizers or test methods for their determination. When more information is available on this subject it will be reconsidered. Manufacturers should refer to the Materials and Articles in Contact with Food Regulations, Statutory Instrument1987 No.1523 and all subsequ

11、ent amendments and to the European Commission Directive “Plastics materials b) the name, trademark or other means of identification and the address in the UK of the manufacturer, distributor or retailer; c) the following instructions in English: “WARNING Inspect immediately before and after each use

12、 and throw away when worn, damaged or punctured, for example by biting. Before use, wash thoroughly and sterilize. Always wash immediately after use. Keep in a dry, covered container. Do not leave in sunlight when not in use. INFANTS MUST NOT BE BOTTLE FED WITHOUT ADULT SUPERVISION. Feeding teats sh

13、ould not be used as dummies/pacifiers/soothers.”; d) instructions on sterilization; e) if it is inappropriate to turn the teat inside out for inspection and cleaning a statement to this effect. If any substance in common household use, likely to come into contact with the teat, is known to have an a

14、dverse effect on the materials of the teat, then each pack shall carry a warning that contact with that substance should be avoided. 7.2 Single use, disposable teats, supplied sterilized ready for use Each pack (see6.2) shall carry the following information in a legible form: a) the information in i

15、tems a) and b) of7.1; b) the following instructions in English; “WARNING Inspect immediately before use and throw away if the pack or its contents are damaged. Do not leave in sunlight prior to use. INFANTS MUST NOT BE BOTTLE FED WITHOUT ADULT SUPERVISION. Feeding teats should not be used as dummies

16、/pacifiers/soothers. Use once only. Do not re-use.”; c) the word “sterilized”. 1) Marking BS7368:1990 on or in relation to a product represents a manufacturers declaration of conformity, i.e. a claim by or on behalf of the manufacturer that the product meets the requirements of the standard. The acc

17、uracy of the claim is therefore solely the responsibility of the person making the claim. Such a declaration is not to be confused with third party certification of conformity, which may also be desirable.BS 7368:1990 BSI 09-1999 3 Appendix A Methods of test for performance of the teat A.1 General A

18、.1.1 Tests shall be conducted at room temperature. A.1.2 For third party certification purposes and for verification of a manufacturers claim that his product conforms to BS7368:1990, the cross-head speed given inA.2 andA.3 shall be used. Alternative manual or mechanical procedures could be used in

19、other situations applying the load gradually over a period of5s. A.2 Tensile strength test Compress opposite sides of the flange together and clamp, perpendicular to the major axis,102mm of the compressed edges of the flange together using a suitable fixture. Hold, perpendicular to the major axis,10

20、2mm of the tip of the nipple in a suitable fixture and apply a tensile force of90 3N to the nipple along the major axis of the teat at a cross-head speed of195mm/min to255mm/min. Apply the full load for10 0.5s. A.3 Bite test Using the test jaws shown inFigure 2, with the nipple section of the teat b

21、etween the jaws apply a force of220 5N to the jaws at a cross-head speed of195mm/min to255mm/min. Apply full load for10 0.5s. NOTEMake sure the machine is capable of stopping at220 5N when using a cross-head speed of 195mm/min to255mm/min or damage to the load cell will result. It is possible to use

22、 a machine to lower a mass equivalent to220N onto the jaw to prevent the load cell from being subjected to a force greater than220N.BS 7368:1990 4 BSI 09-1999 Figure 2 Jaws for bite testBS7368:1990 BSI 09-1999 Publication(s) referred to BS 5239, Specification for babies dummies. BS 5665, Safety of t

23、oys. BS 5665-3, Specification for migration of certain elements. BS 7115, Determination of volatile nitrosamines in rubber teats for feeding bottles and babies dummies. BS 7115-1, Dichloromethane extraction method. EN 71, Safety of toys 2) . EN 71-3, Requirements for the migration of certain element

24、s. Guide to good manufacturing practice for sterile medical devices and surgical products, HMSO,1981 Instructions for consumer products, HMSO,1988 2) . 2) Referred to in the foreword only.BS 7368:1990 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent nati

25、onal body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the

26、latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of whic

27、h can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards pu

28、blications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI

29、provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre.

30、Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Co

31、pyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any f

32、orm or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.