BS 6913-13-1997 Operation and maintenance of earth-moving machinery - Specification for lubrication fittings - Nipple type《运土机械的操作和维修 润滑油配件规范 油嘴类型》.pdf

《BS 6913-13-1997 Operation and maintenance of earth-moving machinery - Specification for lubrication fittings - Nipple type《运土机械的操作和维修 润滑油配件规范 油嘴类型》.pdf》由会员分享，可在线阅读，更多相关《BS 6913-13-1997 Operation and maintenance of earth-moving machinery - Specification for lubrication fittings - Nipple type《运土机械的操作和维修 润滑油配件规范 油嘴类型》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 6913-13: 1997 ISO 6392-1: 1996 Operation and maintenance of earth-moving machinery Part 13: Specification for lubrication fittings Nipple type ICS 53.100BS6913-13:1997 This British Standard, having been prepared under the directionof the Sector Board for Building and Civil Engine

2、ering, was published under the authorityof the Standards Boardand comes into effect on 15 May 1997 BSI 02-1999 The following BSI references relate to the work on this standard: Committee reference B/513/1 Draft for comment 95/101354 DC ISBN 0 580 27390 3 Committees responsible for this British Stand

3、ard The preparation of this British Standard was entrusted by Technical Committee B/513, Construction equipment and plant, and site safety, to Subcommittee B/513/1, Earth-moving machinery, upon which the following bodies were represented: British Coal Corporation Construction Plant (Hire Association

4、) Federation of Civil Engineering Contractors Federation of Manufacturers of Construction Equipment and Cranes Health and Safety Executive Institution of Civil Engineers Silsoe Research Institute Amendments issued since publication Amd. No. Date CommentsBS6913-13:1997 BSI 02-1999 i Contents Page Com

5、mittees responsible Inside front cover National foreword ii 1 Scope 1 2 Normative references 1 3 Description 1 4 Material, design and manufacture 1 5 Shape, dimensions and tolerances 1 6 Proof pressure of fittings 1 7 Required ambient space at the mounting position of fittings 1 Annex A (informative

6、) Bibliography 4 Figure 1 Types of fitting 2 Figure 2 Detailed dimensions of fitting head 3 Figure 3 Clearance space required for uncoupling of nozzle 3 Table 1 Dimensions of fittings 2 List of references Inside back coverBS6913-13:1997 ii BSI 02-1999 National foreword This Part of BS6913 has been p

7、repared by SubcommitteeB/513/1. It is identical with ISO6392-1:1996 Earth-moving machinery Lubrication fittings Part1:Nipple type published by the International Organization for Standardization (ISO). ISO 6392-1 was prepared by Subcommittee3, Operation and maintenance, of ISO Technical Committee127,

8、 Earth-moving machinery, with the active participation and approval of the UK. This text represents a revision, in Parts, of ISO6392:1980. The other Part, ISO6392-2 Earth-moving machinery Lubrication fittings Part2: Grease-gun nozzles is being published in the UK as BS6913-14:1997. The previous edit

9、ion of the British Standard was published as BS6060:1981 which has been withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itsel

10、f confer immunity from legal obligations. Cross-reference International standard Corresponding British Standard BS 6914 Terminology (including definitions of dimensions and symbols) for earth-moving machinery ISO 6165:1987 a Part 1:1988 Glossary of terms for basic types of earth-moving machinery (Id

11、entical) a Currently under revision. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in

12、 the amendment table on theinside front cover.BS6913-13:1997 BSI 02-1999 1 1 Scope This part of ISO6392 specifies nipple-type lubrication fittings, for the types of earth-moving machinery defined in ISO6165, and the space required to service these fittings. NOTEThe lubrication fittings are hereinaft

13、er referred to as fittings. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO6392. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agr

14、eements based on this part of ISO6392 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 2081:1986, Metallic coatings Electroplated coatings of

15、zinc on iron or steel. ISO 6165: 1) , Earth-moving machinery Basic types Vocabulary. 3 Description Fittings for earth-moving machinery shall be of the types shown inFigure 1. 4 Material, design and manufacture 4.1 Material Unless otherwise specified, fittings shall be made from manufacturers standar

16、d steel. 4.2 Hardness Fittings used where there is a high frequency of greasing and/or direct contact with soil or sand shall have their heads surface hardened. In cases where surface-hardening is required, the minimum hardness shall be83HRA or55HR30N and shall have a minimum case depth of0,10mm. Wh

17、ere surface-hardened heads are not required, hardness is not specified in general. 4.3 Finish Bodies of fittings shall be electroplated with zinc and chromate treatment in accordance with ISO2081. The thickness of the coating shall be atleast5m. 4.4 Workmanship Fittings shall be free from burrs, loo

18、se scale, sharp edges, and any other defects that might affect their intended function. 4.5 Check valve Fittings shall be supplied with check valves which will provide a seal against the ingress of foreign material, but will admit lubricant under pressure and prevent its escape. 5 Shape, dimensions

19、and tolerances The shape, dimensions and tolerances of fittings shall conform to the requirements given inFigure 1 andFigure 2 andTable 1. The tabulated dimensions shall apply to the finished processed parts. 6 Proof pressure of fittings Fittings shall accept grease injection at an injection pressur

20、e of up to20MPa. 7 Required ambient space at the mounting position of fittings The required ambient space is such that a grease-gun nozzle, with18mm outer diameter, and its extension can be inclined to a minimum angle of25 in one direction (seeFigure 3). 1) To be published. (Revision of ISO6165:1987

21、)BS6913-13:1997 2 BSI 02-1999 Table 1 Dimensions of fittings Figure 1 Types of fitting Dimensions in millimetres Type No. Type Thread l 1 l 2 l 3 s a l 4 l 5 0,2 0,5 0,5 0,2 max. 1 Straight fitting ISO 261 M6 0,75 8 7 4 5,4 2 Straight fitting ISO 7 R 1/8 11 10 8 5,4 3 45 elbow fitting ISO 7 R 1/8 12

22、,5 8,5 10 8 5,4 4 65 to 67,5 elbow fitting ISO 7 R 1/8 12,5 8,5 10 8 5,4 5 90 elbow fitting ISO 7 R 1/8 12,5 8,5 10 8 5,4 a Across flats of hexagon. 00,2 BS6913-13:1997 BSI 02-1999 3 Dimensions in millimetres d a 6,55 0,25 d 1 a 4,6 0,3 d 2 5,4 0,3 h 1 2,5 0,3 h 2 2,3 0,1 R 1 6 0,2 R 2 0,8 0,1 a d d

23、 1 1 mm Figure 2 Detailed dimensions of fitting head Figure 3 Clearance space required for uncoupling of nozzleBS6913-13:1997 4 BSI 02-1999 Annex A (informative) Bibliography 1 ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads Part1: Dimensions, tolerances and designatio

24、n. 2 ISO 261:1973, ISO general purpose metric screw threads General plan. 3 ISO 674:1988, Metallic materials Hardness test Calibration of standardized blocks to be used for Rockwell hardness testing machines (scales A B C D E F G H K). 4 ISO 1355:1989, Metallic materials Hardness test Calibration of

25、 standardized blocks to be used for Rockwell superficial hardness testing machines (scales15N,30N,45N,15T,30T and45T).BS6913-13:1997 BSI 02-1999 List of references See national foreword.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

26、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It

27、presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim o

28、f BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 899

29、6 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Servi

30、ces. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on n

31、ational, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. S

32、ubscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI p

33、ublications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electroni

34、c, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.