BS 6200-4-1989 Sampling and analysis of iron steel and other ferrous metals - Recommendations for the order of listing elements in the chemical analysis of steel《铁、钢和其他黑色金属抽样与分析法 第.pdf

《BS 6200-4-1989 Sampling and analysis of iron steel and other ferrous metals - Recommendations for the order of listing elements in the chemical analysis of steel《铁、钢和其他黑色金属抽样与分析法 第.pdf》由会员分享，可在线阅读，更多相关《BS 6200-4-1989 Sampling and analysis of iron steel and other ferrous metals - Recommendations for the order of listing elements in the chemical analysis of steel《铁、钢和其他黑色金属抽样与分析法 第.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 6200-4: 1989 Sampling and analysis of iron, steel and other ferrous metals Part 4: Recommendations for the order of listing elements in the chemical analysis of steel UDC 001.818:543:669.114BS 6200-4:1989 This British Standard, having been prepared under the directionof the Iron

2、and Steel Standards Policy Committee, waspublished under the authorityof the Board of BSI andcomes into effect on 31 December 1989 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference ISM/18 Draft for approval 87/44207 DC ISBN 0 580 17826 9 Foreword This

3、Part of BS 6200 has been prepared under the direction of the Iron and Steel Standards Policy Committee. It is based on ISO/TR 6306:1989 “Chemical analysis of steel Order of listing elements”, published by the International Organization for Standardization (ISO) to which it is technically equivalent.

4、 It supersedes BS5259:1976, which is withdrawn. The sequence in which elements are listed in steel specifications and analysis reports has never been standardized and varies considerably between different organizations. Although this has always been a potential source of confusion, the cost and temp

5、orary inconvenience of standardizing the order has not been considered worthwhile. The modern tendency towards international standardization and the use of computers for storing, processing and retrieving information has greatly increased the case for standardizing the order of listing elements. Thi

6、s is particularly so when data from several sources are processed by a single computer. Consequently, there is a growing awareness of the long-term advantages of national and international standardization. Some measure of international agreement has already been achieved in steel specifications deve

7、loped by ISO/TC 17/SC 4, Heat treatable and alloy steels, for the first five elements and this has been incorporated into the recommendations given in this British Standard. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are resp

8、onsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, page1 and a back cover. This standard has been updated (see copyright date

9、) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue CommentsBS 6200-4:1989 BSI 09-1999 i Contents Page Foreword Inside front cover 1 Scope 1 2 Recommendations 1ii blankBS 6200-

10、4:1989 BSI 09-1999 1 1 Scope This Part of BS 6200 gives recommendations for an order for listing elements determined in steels and most other iron-based alloys, excluding foundry irons, where the priorities are different. 2 Recommendations The elements are divided into four groups. These groups have

11、 no real technical significance but they are considered to provide the easiest means of readily remembering the recommended order. Group 1 includes the five elements that are regarded as the most important in all types of steel, in the order recommended by ISO/TC17/SC4. Also included in this group a

12、re the three elements of next greatest importance in alloy steels. These follow the first five arranged in alphabetical order of their chemical symbols. Group 2 includes another13 elements that are commonly determined in a wide variety of commercial steels. These are arranged in alphabetical order o

13、f their chemical symbols. Group 3 is reserved for any element not assigned a place in the set order. When more than one such element is determined they should be arranged in alphabetical order of their chemical symbols. Group 4 is reserved for hydrogen. The recommended order is thus as follows: a) C

14、 Si Mn P S Cr Mo Ni; b) Al As B Co Cu N Nb Pb Sn Ti V W Zr; c) Other elements determined, in alphabetical order of their chemical symbols; d) H. With the exception of hydrogen, elements should be reported in per cent by mass % (M/M) irrespective of the content. Hydrogen should be reported in microgr

15、ams per gram (4g/g).BS 6200-4: 1989 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Char

16、ter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccurac

17、y or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscrib

18、ers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply

19、the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI e

20、lectronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price

21、of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitte

22、d under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of

23、implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.