BS 6102-13-1991 Cycles - Specification for mating dimensions for splined hub and sprocket《自行车 第13部分 花键毂和后链轮配合尺寸规范》.pdf

《BS 6102-13-1991 Cycles - Specification for mating dimensions for splined hub and sprocket《自行车 第13部分 花键毂和后链轮配合尺寸规范》.pdf》由会员分享，可在线阅读，更多相关《BS 6102-13-1991 Cycles - Specification for mating dimensions for splined hub and sprocket《自行车 第13部分 花键毂和后链轮配合尺寸规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 6102-13: 1991 ISO 10230: 1990 Cycles Part 13: Specification for mating dimensions for splined hub and sprocketBS6102-13:1991 This British Standard, having been prepared under the direction of the General Mechanical Engineering Standards Policy Committee, was published under the a

2、uthority of the Standards Board and comes into effect on 28 June 1991 BSI 07-1999 The following BSI references relate to the work on this standard: Committee reference GME/25 Draft for comment 89/70617 DC ISBN 0 580 19739 5 Committees responsible for this British Standard The preparation of this Bri

3、tish Standard was entrusted by the General Mechanical Engineering Standards Policy Committee (GME/-) to Technical Committee GME/25, upon which the following bodies were represented: Association for Consumer Research Association of Consulting Scientists Association of Cycle Traders Bicycle Associatio

4、n of Great Britain British Battery Manufacturers Association British Cycling Federation British Rubber Manufacturers Association Consumer Policy Committee of BSI Cyclists Touring Club Department of Transport Institute of Trading Standards Administration Royal Society for the Prevention of Accidents

5、Small Electrical Appliances Marketing Association Coopted members Amendments issued since publication Amd. No. Date CommentsBS6102-13:1991 BSI 07-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 Dimensions and tolerances 1 Figure 1 Mating dimensions of

6、hub and sprocket 1 Publication(s) referred to Inside back coverBS6102-13:1991 ii BSI 07-1999 National foreword This Part of BS 6102 has been prepared under the direction of the General Mechanical Engineering Standards Policy Committee and forms part of a series implementing corresponding internation

7、al standards in the development of which the United Kingdom has played an active part. This standard is identical with ISO 10230:1990 “Cycles Splined hub and sprocket Mating dimensions”, which was prepared by Technical Committee ISO/TC 149 of the International Organization for Standardization (ISO).

8、 Cross-reference. The Technical Committee has reviewed the provisions of ISO1101:1983 and ISO2692:1988 to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. A related British Standard to ISO1101:1983 and ISO2692:1988 is BS308-3:19

9、72 “Geometrical tolerancing”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of

10、pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front co

11、ver.BS6102-13:1991 BSI 07-1999 1 1 Scope This International Standard specifies mating dimensions and tolerances for the sprocket and splines of the hub of an internally geared hub or a backpedal brake hub on a cycle. 2 Dimensions and tolerances The dimensions and tolerances for the fitting of a spro

12、cket to a splined hub shall be as given in Figure 1. NOTE 1Meanings of tolerance symbols are given in ISO1101:1983, Technical drawings Geometrical tolerancing Tolerancing of form, orientation, location and run-out Generalities, definitions, symbols, indications on drawings and ISO2692:1988, Technica

13、l drawings Geometrical tolerancing Maximum material principle. 1)See note in clause 2. Figure 1 Mating dimensions of hub and sprocket2 blankBS6102-13:1991 BSI 07-1999 Publication(s) referred to See national foreword.BS 6102-13: 1991 ISO 10230: 1990 BSI 389 Chiswick High Road London W4 4AL BSIBritish

14、StandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishS

15、tandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the techn

16、ical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for

17、 all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless ot

18、herwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its product

19、s and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration

20、. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, store

21、d in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grad

22、e designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.