BS 6101-5-1992 Machine tool ball screws - Specification for nominal diameters and nominal leads《机床滚珠丝杠 第5部分 公称直径和额定负载规范》.pdf

《BS 6101-5-1992 Machine tool ball screws - Specification for nominal diameters and nominal leads《机床滚珠丝杠 第5部分 公称直径和额定负载规范》.pdf》由会员分享，可在线阅读，更多相关《BS 6101-5-1992 Machine tool ball screws - Specification for nominal diameters and nominal leads《机床滚珠丝杠 第5部分 公称直径和额定负载规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 6101-5: 1992 ISO 3408-2: 1991 Machine tool ball screws Part 5: Specification for nominal diameters and nominal leads UDC 62-234BS6101-5:1992 This British Standard, having been prepared under the directionof the Machine, Engineers and Hand Tools Standards Policy Committee, waspubl

2、ished under the authorityof the Standards Boardand comes into effecton 15October1992 BSI 12-1999 First published August 1984 Second edition October 1992 The following BSI references relate to the work on this standard: Committee reference MTE/1 Draft for comment 88/70387 DC ISBN 0 580 21200 9 Commit

3、tees responsible for this British Standard The preparation of this British Standard was entrusted by the Machine, Engineers and Hand Tools Standards Policy Committee (MTE/-) to Technical Committee MTE/1, upon which the following bodies were represented: Advanced Manufacturing Technology Research Ins

4、titute Cranfield Institute of Technology Health and Safety Executive Machine Tool Technologies Association Ministry of Defence Coopted members Amendments issued since publication Amd. No. Date CommentsBS6101-5:1992 BSI 12-1999 i Contents Page Committees responsible Inside front cover National forewo

5、rd ii 1 Scope 1 2 Normative reference 1 3 Definitions 1 4 Nominal diameters 1 5 Nominal leads 1 6 Combinations of nominal diameters and nominal leads 1 Table 1 1 Table 2 2 List of references Inside back coverBS6101-5:1992 ii BSI 12-1999 National foreword This Part of BS6101 has been prepared under t

6、he direction of the Machine, Engineers and Hand Tools Standards Policy Committee. It is identical with ISO3408:1991 Ball screws Part2 Nominal diameters and nominal leads Metric series, prepared by the International Organization for Standardization (ISO). This edition supersedes BS6101-5:1984 which i

7、s withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Internationa

8、l Standard Corresponding British Standard ISO 3408-1:1991 BS 6101 Machine tool ball screws Part 3:1992 Glossary of terms (Identical) Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2, an inside back cover and a back cover. This standard has been

9、 updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS6101-5:1992 BSI 12-1999 1 1 Scope This part of ISO3408 specifies the nominal diameters and nominal leads, metric series, for ball screws. It also gives pr

10、eferred combinations of nominal diameter and nominal lead and a general plan which includes additional combinations to be used when it becomes necessary to deviate from the preferred combinations. 2 Normative reference The following standard contains provisions which, through reference in this text,

11、 constitute provisions of this part of ISO3408. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this part of ISO3408 are encouraged to investigate the possibility of applying the most recent edition of the standar

12、d indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 3408-1:1991, Ball screws Part 1: Vocabulary and designation. 3 Definitions For the purposes of this part of ISO3408, the definitions given in ISO3408-1 apply. 4 Nominal diameters The followin

13、g series of nominal diameters, in millimetres, shall be used: 6 8 10 12 16 20 25 32 40 50 63 80 100 125 160 and 200. 5 Nominal leads The following series of nominal leads, in millimetres, shall be used: 1 2 2,5 3 4 5 6 8 10 12 16 20 25 32 and 40. Where possible, preference shall be given to the foll

14、owing nominal leads, in millimetres: 2,5 5 10 20 and 40. 6 Combinations of nominal diameters and nominal leads 6.1 Preferred combinations SeeTable 1. 6.2 General plan SeeTable 2. For preferred combinations, use the nominal lead values which are underlined. When it becomes necessary to deviate from t

15、he preferred combinations, use the nominal lead values which are not underlined. Table 1 Dimensions in millimetres Nominal diameter Nominal lead 6 2,5 8 2,5 10 2,5 5 12 2,5 5 10 16 2,5 5 10 20 5 10 20 25 5 10 20 32 5 10 20 40 5 10 20 40 50 5 10 20 40 63 5 10 20 40 80 10 20 40 100 10 20 40 125 10 20

16、40 160 20 40 200 20 40BS6101-5:1992 2 BSI 12-1999 Table 2 Dimensions in millimetres Nominal diameter Nominal lead 6 1 2 2,5 8 1 2 2,5 3 10 1 2 2,5 3 4 5 6 12 2 2,5 3 4 5 6 8 10 12 16 2 2,5 3 4 5 6 8 10 12 16 20 3 4 5 6 8 10 12 16 20 25 4 5 6 8 10 12 16 20 25 32 4 5 6 8 10 12 16 20 25 32 40 5 6 8 10

17、12 16 20 25 32 40 50 5 6 8 10 12 16 20 25 32 40 63 5 6 8 10 12 16 20 25 32 40 80 6 8 10 12 16 20 25 32 40 100 10 12 16 20 25 32 40 125 10 12 16 20 25 32 40 160 12 16 20 25 32 40 200 12 16 20 25 32 40BS6101-5:1992 BSI 12-1999 List of references See national foreword.BS 6101-5: 1992 ISO 3408-2: 1991 B

18、SI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are u

19、pdated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Briti

20、shStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest

21、editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that

22、have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are al

23、so available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these an

24、d other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and P

25、atents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necess

26、ary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.