BS 6092-11-1981 Methods of sampling and test for sodium and potassium silicates for industrial use - Determination of chloride content of sodium metasilicate《工业用硅酸钠和硅酸钾取样和试验方法 第11部.pdf

《BS 6092-11-1981 Methods of sampling and test for sodium and potassium silicates for industrial use - Determination of chloride content of sodium metasilicate《工业用硅酸钠和硅酸钾取样和试验方法 第11部.pdf》由会员分享，可在线阅读，更多相关《BS 6092-11-1981 Methods of sampling and test for sodium and potassium silicates for industrial use - Determination of chloride content of sodium metasilicate《工业用硅酸钠和硅酸钾取样和试验方法 第11部.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 6092-11: 1981 Methods of Sampling and test for sodium and potassium silicates for industrial use Part 11: Determination of chloride content of sodium metasilicate NOTEIt is recommended that this Part be read in conjunction with the information in the “General introduction” publis

2、hed separately as BS 6092-0. UDC 661.683/.684:546.32284 + 546.33284:543.24.062:546.131BS6092-11:1981 This British Standard, having been prepared under the directionof the Chemicals Standards Committee, was published under the authorityofthe Executive Boardand comes into effect on 27February1981 BSI

3、12-1999 The following BSI references relate to the work on this standard: Committee reference CIC/22 Draft for comment 73/55424 DC ISBN 0 580 12048 1 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correc

4、t application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyri

5、ght date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue CommentsBS6092-11:1981 BSI 12-1999 i Contents Page 1 Scope 1 2 References 1 3 Principle 1 4 Reagents 1 5 Apparatus 1

6、 6 Procedure 1 7 Expression of results 1 Publications referred to Inside back coverii blankBS6092-11:1981 BSI 12-1999 1 1 Scope This Part of BS6092describes a method of test for determining the chloride content of sodium metasilicate pentahydrate and is applicable to products having chloride content

7、s, expressed as sodium chloride (NaCl) in the range0.03% to0.55% (m/m). There is no International Standard corresponding to this Part of BS 6092. 2 References The titles of the publications referred to in this standard are listed on the inside back cover. 3 Principle A solution of the test portion i

8、s mixed with silver nitrate solution and the excess of silver nitrate is titrated with ammonium thiocyanate solution using ammonium iron (III) sulphate solution as indicator. 4 Reagents The following reagents are required and shall be of recognized analytical quality. Water complying with the requir

9、ements of BS3978shall be used throughout. 4.1 Nitrobenzene. WARNING. Serious risk of poisoning by inhalation, swallowing or skin contact. Avoid breathing vapour. Prevent contact with skin and eyes. 4.2 Nitric acid, approximately5N solution. 4.3 Silver nitrate, 0.1N standard volumetric solution. 4.4

10、Ammonium thiocyanate, 0.1N standard volumetric solution. 4.5 Ammonium iron (III) sulphate indicator solution,100g/l. Dissolve25g of ammonium iron(III) sulphate in250ml of water. Allow the solution to settle and decant if necessary. If the solution is still not clear, add a few drops of approximately

11、5N nitric acid solution. 5 Apparatus Ordinary laboratory apparatus is required. 6 Procedure 6.1 Test portion. Weigh, to the nearest0.1g, 10g of the sample. 6.2 Determination. Transfer the test portion(6.1) to a500ml stoppered flask (an iodine flask, complying with the requirements of BS2735is suitab

12、le). Add250ml of water, warming if necessary to complete dissolution of the solid. Cool the solution to room temperature and add25ml of the nitric acid solution (4.2). Prepare a blank solution from250ml of water and25ml of the nitric acid solution (4.2) in a second, similar, flask. To each flask add

13、10ml of the silver nitrate solution (4.3) from a pipette, followed by2ml of the nitrobenzene (4.1) and1ml of the ammonium iron (III) sulphate indicator solution(4.5). Stopper the flasks and shake them for about30s. Titrate the blank solution with the ammonium thiocyanate solution (4.4) until a faint

14、 pink-brown colour just persists throughout the solution. Similarly titrate the test solution to a matching end-point. 7 Expression of results The chloride content, expressed as a percentage by mass of sodium chloride (NaCl), is given by the formula: where V 1 is the volume of the ammonium thiocyana

15、te solution (4.4) required for the blank test, inml; V 2 is the volume of the ammonium thiocyanate solution (4.4) required for the test solution, inml; 10 is the mass of the test portion, in g.2 blankBS6092-11:1981 BSI 12-1999 Publications referred to BS 2735, Iodine flasks. BS 3978, Water for labor

16、atory use. BS 6092-11: 1981 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Rev

17、isions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or amb

18、iguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers auto

19、matically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI

20、implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electroni

21、c information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of stand

22、ards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under

23、 the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of impleme

24、nting the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.