BS 5F 54-2002 Heavy duty linen (flax) sewing thread for aerospace purposes《航天航空用重型亚麻缝纫线》.pdf

《BS 5F 54-2002 Heavy duty linen (flax) sewing thread for aerospace purposes《航天航空用重型亚麻缝纫线》.pdf》由会员分享，可在线阅读，更多相关《BS 5F 54-2002 Heavy duty linen (flax) sewing thread for aerospace purposes《航天航空用重型亚麻缝纫线》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS 5F 54:2002 (Superseding BS 4F 54:1985) Heavy duty linen (flax) sewing thread for aerospace purposes ICS 49.025.60 BS 5F 54:2002 This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published

2、under the authority of the Sector Policy and Strategy Committee on 17 October 2002 BSI 17 October 2002 First published BS F 54:1930 Second edition BS 2F 54:1960 Third edition BS 3F 54:1975 Fourth edition BS 4F 54:1985 Fifth edition BS 5F 54:2002 The following BSI references relate to the work on thi

3、s standard: Draft for comment 00/707767 DC Committee reference ACE/22 ISBN 0 580 37035 6 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/22, Cords, ropes and threads for aerospace purposes, upon which the following bo

4、dies were represented: Linen Sewing Threads Manufacturers Association Ministry of Defence UK Defence Standardization Society of British Aerospace Companies Ltd. Amendments issued since publication Amd. No. Date CommentsBS 5F 54:2002 BSI 17 October 2002 i Contents Page Committees responsible Inside f

5、ront cover Foreword ii 1S c o p e 1 2 Normative references 1 3G e n e r a l 1 4Y a r n 1 5 Finish 2 6 Construction and properties 2 7 Identification 2 Bibliography 3 Table 1 General requirements (given in BS F 100) 1 Table 2 Construction and properties 2BS 5F 54:2002 ii BSI 17 October 2002 Foreword

6、This British Standard, prepared under the direction of Technical Committee ACE/22, is one of a series for textiles of a quality suitable for aerospace purposes. It supersedes BS 4F 54:1985 which is withdrawn. NOTE The previous edition, BS 4F 54:1985, differed from the earlier edition in that it requ

7、ired all thread be supplied rotproofed. This new edition incorporates all earlier amendments, updates references and improves nomenclature in line with other standards in the same series. This publication does not purport to include all the necessary provisions of a contract. Users are responsible f

8、or its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. WARNING NOTES This standard calls for the use of substances and/or test procedures that may be injurious to health if adequate precautions are not taken. It refers only to techni

9、cal suitability and in no way absolves either the supplier or the user from statutory obligations relating to health and safety at any stage of manufacture or use. This standard specifies pentachlorophenyl laurate (PCPL) as the only approved rotproofing treatment for aerospace textiles. Alternative

10、treatments are under development, and this standard will be updated to delete PCPL as soon as an approved alternative treatment for aerospace textiles is available. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 3 and a back cover. The BSI c

11、opyright notice displayed in this document indicates when the document was last issued.BS 5F 54:2002 BSI 17 October 2002 1 1 Scope This British Standard specifies requirements for heavy duty linen (flax) sewing thread for aerospace purposes. NOTE The latest revision of an Aerospace Series standard i

12、s indicated by a prefix number. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) app

13、lies. BS 2087-1, Preservative treatments for textiles Specification for treatments. BS F 100, Procedure for inspection and testing of textiles for aerospace purposes. BS EN ISO 2060:1995, Textiles Yarn from packages Determination of linear density (mass per unit length) by the skein method. BS EN IS

14、O 2061, Textiles Determination of twist in yarns Direct counting method. 3 General 3.1 General In addition to the requirements specified in Clause 4, Clause 5, Clause 6 and Clause 7 of this standard the requirements and tests given in the latest edition of BS F 100 as specified in Table 1, shall app

15、ly. Table 1 General requirements (given in BS F 100) 3.2 Freedom from faults The thread shall have uniformity of thickness, construction, and component ply tension so that there are no visually irregular twist faults. The thread shall contain no thread knots. 3.3 Length per unit mass The length per

16、unit mass of thread shall be determined in accordance with BS EN ISO 2060:1995, Option 1. 4 Yarn 4.1 The thread shall be manufactured from flax fibre (Linum usitatissimum). 4.2 The mass of the yarn shall be reduced by not less than 10 % by boiling. NOTE The degree of boiling of the yarn should be de

17、termined from the manufacturers records, where available. Otherwise, the residual alkali solubility of the thread should be determined and should not exceed 10 %. Section of BS F 100 Section title Requirements and tests 1 General All requirements 2 a Quality requirements Requirements for dyed textil

18、es except those related to fabric intended for coating. Requirements for freedom from corrosive impurities (see BS F 100, Section 4). 3 Physical tests Tests for breaking strength and extension under force 4C h e m i c a l tests Test for residual alkali solubility. If required by BS F 100, Section 2:

19、 test for conductivity of aqueous extract; test for pH value of aqueous extract; test for water soluble chloride; test for water soluble sulfate. a It is not intended that BS F 100, Section 2 tests should be performed on each thread batch. The frequency of these tests should be agreed between the Qu

20、ality Assurance Authority and the thread manufacturer, see BS F 100.BS 5F 54:2002 2 BSI 17 October 2002 5 Finish 5.1 Condition of material The thread shall be supplied in one of the following conditions: a) undyed and rotproofed; b) undyed, rotproofed and wax finished; c) dyed and rotproofed; d) dye

21、d, rotproofed and wax finished. 5.2 Dyeing Where dyeing is required, the colour shall be specified either by reference to a British Standard, e.g. BS 381C, or by pattern. 5.3 Rotproofing The thread shall be treated with pentachlorophenyl laurate (PCPL) from aqueous emulsion, normal process, in accor

22、dance with BS 2087-1, normal process. 5.4 Wax finishing Where wax finishing is required, beeswax substitute microcrystalline hydrocarbon wax shall be used and the added mass due to the wax shall be (20 5) %. Prior to waxing, the thread shall have been rotproofed in accordance with 5.3. 5.5 Surface f

23、inish Thread supplied in accordance with item 5.1a) or 5.1c) shall have a soft, smooth finish, but substances that may promote microbiological growth (e.g. starch or modified starch) shall not be applied. 6 Construction and properties 6.1 Where undyed thread is supplied, the thread shall conform to

24、the requirements given in Table 2. 6.2 Where dyed thread is supplied, the thread shall conform to the requirements of Table 2 except that the minimum breaking strengths shall be reduced by 10 %. NOTE Unless otherwise specified, the direction of final twist should be Z. Table 2 Construction and prope

25、rties 7 Identification The thread shall be identified by the number of this British Standard, i.e. BS 5F 54, together with the finish and, if required dyed, the colour. NOTE This identification may be codified. For example, thread required dyed black and unwaxed may be identified as “BS 5F 54/black/

26、unwaxed”. Nominal resultant linear density Number of plies Final twist a Length per unit mass b Minimum breaking strength unwaxed waxed tex Turns/m m/kg N N 690 8 118 6 1 450 160 220 180 a The final twist shall be determined in accordance with BS EN ISO 2061. b The length per unit mass shall be dete

27、rmined by weighing a skein conditioned and reeled in accordance with BS EN ISO 2060:1995, Option 1. The values stated for length per unit mass exclude the mass of added dye and/or finishes.BS 5F 54:2002 BSI 17 October 2002 3 Bibliography Standards publications BS 381C:1996, Specification for colours

28、 for identification, coding and special purposes.BS 5F 54:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. I

29、t is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be gratef

30、ul if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual upda

31、ting service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: o

32、rdersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provid

33、es a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +

34、44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 89

35、96 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publ

36、ications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic,

37、photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.