BS 5350-B5-1976 Methods of test for adhesives - Determination of gelation time《粘合剂试验方法 第B5部分 胶凝时间的测定》.pdf

《BS 5350-B5-1976 Methods of test for adhesives - Determination of gelation time《粘合剂试验方法 第B5部分 胶凝时间的测定》.pdf》由会员分享，可在线阅读，更多相关《BS 5350-B5-1976 Methods of test for adhesives - Determination of gelation time《粘合剂试验方法 第B5部分 胶凝时间的测定》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 5350-B5: 1976 Incorporating Amendment No. 1 Methods of test for Adhesives Part B5: Determination of gelation time UDC 665.93:620.1 + 665.93:66.095.26 40BS5350-B5:1976 BSI 11-1999 ISBN 0 580 09103 1 Foreword Gelation time, as defined in clause3, is applicable to solvent-containing

2、 and solventless systems and provides a simple means of assessing the rate of polymerization or the efficiency of curing agents. Certain systems when fully cured may only develop very soft gels which break into lumps upon inversion of the tubes. Similar systems, at an earlier stage of polymerization

3、, will flow evenly and this difference in behaviour may provide an adequate criterion. With hot-melt adhesives, dwell time in the hot application equipment is important. A method for the determination of heat stability of hot-melt adhesives is given in BS5350-H1. A British Standard does not purport

4、to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover

5、, pages i and ii, page 1 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date Comments 5359 February 1987 Indicated by

6、 a sideline in the marginBS5350-B5:1976 BSI 11-1999 i Contents Page Foreword Inside front cover 1 Scope 1 2 References 1 3 Definition 1 4 Method 1: gelation time at 25 C of solvent-containing adhesives 1 5 Method 2: gelation time for solventless adhesives 1 6 Expression of results 1 7 Test report 1i

7、i blankBS5350-B5:1976 BSI 11-1999 1 1 Scope Two methods of test are specified in this Part. Method 1 has an arbitrary endpoint and is suitable for comparative and quality control purposes. Method 2 is suitable for solventless systems and corresponds to BS2782:Method 835C:1980. It can be used for hig

8、h-viscosity materials, which may contain a proportion of solvent. 2 References This Part makes reference to the following standards publications: BS 2782, Methods of testing plastics Method835CDetermination of gelation time of polyester and epoxide resins using a gel timer. BS 5350, Methods of test

9、for adhesives PartH1Determination of heat stability of hot melt adhesives in the application equipment . 3 Definition For the purposes of this Part, the following definition applies. gelation time the time taken for a two (or more) part system to form a gel of reproducible, but arbitrary, consistenc

10、y under standard conditions 4 Method 1: gelation time at 25 C of solvent-containing adhesives 4.1 Principle. The adhesive components are mixed at a specified temperature and maintained, in stoppered glass tubes, at an even temperature. The contents are examined at specified periods for evidence of f

11、low. 4.2 Apparatus 4.2.1 Constant-temperature bath (or oven) capable of being controlled at25 0.2 C. 4.2.2 Glass tubes of approximately150ml capacity and approximately35mm internal diameter, each fitted with an airtight stopper. 4.2.3 Timing device, accurate to1min or less. 4.3 Procedure. Bring the

12、individual components to a temperature of25 1 C and then mix in the proportions and manner described by the manufacturer. The proportions shall be accurate to within2.5% of those specified by the manufacturer. Unless the manufacturers instruction require otherwise, complete the addition and intermix

13、ing of the components in not less than60s and start the timing device as soon as the addition of the final component is completed. Place approximately75ml of the mixed adhesive into each of several of the glass tubes, fit the stoppers and place the tubes vertically in the water bath or oven(4.2.1),

14、controlled at25 0.2 C. Shield the tubes and contents from direct sunlight and leave them undisturbed for a suitable period until tested. NOTEThe preferred periods (in hours) are 2, 8, 24, 36, 48, 72 and 96, but other periods may be selected if necessary so that the final inspection occurs shortly af

15、ter the critical gel formation. If the gel time is required to be less than or more than a specified period, only one tube need be prepared and tested; the method then becomes a pass-or-fail test. At the conclusion of each selected period, invert one tube for30s and examine the contents visually for

16、 signs of flow. Note the time and discard the tube. The gelation time is taken as the time when the contents have ceased to flow. 5 Method 2: gelation time for solventless adhesives Use the method for determining the gelation time of epoxide resins in BS2782:Method 835C:1980. 6 Expression of results

17、 Express the results of the test in hours and minutes as appropriate. 7 Test report The test report shall state the following: a) a designation of the adhesive, giving all information required for complete identification of the sample: b) the mixing proportions of the ingredients; c) the time interv

18、al between mixing and testing; d) the presence or absence of flow after the selected test periods. e) the gelation time of the material; f) the reference to this Part, i.e. BS5350-B5, method1 or method2.BS 5350-B5: 1976 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is t

19、he independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure tha

20、t they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, t

21、he identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and f

22、oreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Informatio

23、n on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the I

24、nformation Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:020899

25、67001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or t

26、ransmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.