BS 5279-1976 Specification for dimensions of fuel filler openings of earth-moving machinery《运土机械加油孔尺寸规范》.pdf

《BS 5279-1976 Specification for dimensions of fuel filler openings of earth-moving machinery《运土机械加油孔尺寸规范》.pdf》由会员分享，可在线阅读，更多相关《BS 5279-1976 Specification for dimensions of fuel filler openings of earth-moving machinery《运土机械加油孔尺寸规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 5279:1976 ISO 3541:1975 Specification for Dimensions of fuel filleropenings of earth-moving machinery UDC 629.11-479:622.232:62-225.12-181BS5279:1976 This British Standard, having been prepared under the directionof the Road EngineeringStandards Committee was published underthe a

2、uthority of the Executive Board on 31 March1976 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference RDB/21 Draft for comment 74/43847 ISBN 0 580 09163 5 Cooperating organizations The Road Engineering Standards Committee, under whose supervision this Brit

3、ish Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: Asphalt and Coated Macadam Association Association of Consulting Engineers British Quarrying and Slag Federation British Tar Industry Association Cement and C

4、oncrete Association Concrete Society (Design and Development Divisional Committee) Contractors Plant Association* County Surveyors Society Department of the Environment* Department of the Environment, Transport and Road Research Laboratory Federation of Civil Engineering Contractors* Federation of M

5、anufacturers of Construction Equipment and Cranes* Greater London Council Institute of Petroleum Institute of Quarrying Institution of Civil Engineers* Institution of Highway Engineers* Institution of Municipal Engineers* Institution of Structural Engineers Ministry of Defence* Refined Bitumen Assoc

6、iation Limited Road Emulsion Association Limited Road Surface Dressing Association Sand and Gravel Association Limited Society of Chemical Industry Individual experts The organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee

7、entrusted with the preparation of this British Standard: Associated Offices Technical Committee British Steel Industry Department of Employment Department of Industry National Coal Board Individual experts Amendments issued since publication Amd. No. Date of issue CommentsBS5279:1976 BSI 12-1999 i C

8、ontents Page Cooperating organizations Inside front cover Foreword ii 1 Scope and field of application 1 2 Terminology 1 3 Sizes 1 4 Dimensions 2BS5279:1976 ii BSI 12-1999 Foreword This British Standard has been prepared under the authority of the Road Engineering Standards Committee. The text of th

9、is standard is identical to that of the published International Standard 3541 “Earth moving machinery Dimensions of fuel filler openings” which was produced as a result of international discussions in which the UK took an active part. For the purposes of this British Standard the text of ISO 3541 sh

10、ould be modified as follows. Terminology. The words “British Standard” should replace the words “International Standard” wherever they occur. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applic

11、ation. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 and 2 and a back cover. This standard has been updated (see copyright date) and may have had amen

12、dments incorporated. This will be indicated in the amendment table on the inside front cover.BS5279:1976 BSI 12-1999 1 1 Scope and field of application This International Standard lays down the dimensions of fuel filler openings and caps for earth-moving machinery. 2 Terminology The terminology rela

13、ting to the parts of the fuel filler opening is as follows. 3 Sizes Fuel filler openings shall be of three nominal sizes: 50, 75 and 100 mm.BS5279:1976 2 BSI 12-1999 4 Dimensions 4.1 Fuel filler opening 4.2 Cap 4.3 Connection of cap to fuel tank The cap should be connected to the fuel tank by a chai

14、n or similar link. Dimensions in millimetres (Inch values in parentheses) a Nominal size Nominal size ofthread d D min. D L 1min. L 2 L 3min. 50 (2) M 60 3 (2 1/2 p 12UN) 50 (2) 40 (1 5/8) 30 (1 1/4) 20 (7/8) 300 (12) 75 (3) M 90 3 (3 1/2 p 12UN) 75 (3) 65 (2 9/16) 100 (4) M 120 3 (4 3/4 p 12UN) 100

15、 (4) 90 (3 9/16) a The inch threads shown are not interchangeable with the metric threads. Dimensions in millimetres (Inch values in parentheses) a Nominal size Nominal size of thread d L 50 (2) M 60 3 (2 1/2 p 12UN) 18 (3/4) 75 (3) M 90 3 (3 1/2 p 12UN) 100 (4) M 120 3 (4 3/4 p 12UN) a The inch thr

16、eads shown are not interchangeable with the metric threads.blankBS 5279:1976 ISO3541:1975 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the

17、 international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and service

18、s. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual up

19、dating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders fo

20、r international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and

21、its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments an

22、d receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the i

23、nternational standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.

24、 This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.