BS 5278-1976 Doors Measurement of dimensions and of defects of squareness of door leaves《门 门扇尺寸及方正度缺陷的测量》.pdf

《BS 5278-1976 Doors Measurement of dimensions and of defects of squareness of door leaves《门 门扇尺寸及方正度缺陷的测量》.pdf》由会员分享，可在线阅读，更多相关《BS 5278-1976 Doors Measurement of dimensions and of defects of squareness of door leaves《门 门扇尺寸及方正度缺陷的测量》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS5278:1976 EN25 Doors Measurement of dimensions and of defects of squareness of door leaves This European Standard EN 25 was given as from 30 January 1976 the status of a British Standard. UDC 69.028.141:620.1:531.717:531.74BS5278:1976 This British Standard was published under the

2、authority of the Executive Board on 31March1976 BSI 03-1999 The following BSI references relate to the work on this standard: Committee reference B/141 Draft for comment73/10217 ISBN 0 580 08628 3 Co-operating organizations The European Committee for Standardization, under whose supervision this Eur

3、opean Standard was prepared, comprise the national standards organizations of the following Western European countries: A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with

4、 a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) an

5、d may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Austria Oesterreichisches Normungsinstitut Belgium Institut Belge de Normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliitto, r.y. France Association Franais

6、e de Normalisation Germany Deutscher Normenausschuss Ireland Institute for Industrial Research and Standards Italy Ente Nazionale Italiano di Unificazione Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Repartio de Normalizao Sweden Sveriges Standardiseri

7、ngskommission Switzerland Association Suisse de Normaiisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date of issue CommentsBS 5278:1976 BSI 03-1999 i Contents Page Co-operating organizations Inside front cover Brief history 2 Text of EN 25:1975 3 Na

8、tional appendix A Inside back coverii blankEuropean Standard Norme Europenne Europische Norm EN25 First edition June 1975 UDC69.028.141:620.1:531.717:531.74 Descriptors: Doors, geometric characteristics, dimensional measurement, verifying English version Doors Measurement of dimensions and of defect

9、s of squareness of door leaves Portes. Mesurage des dimensions et des dfauts dequerragee des vantaux de porte Turen. Prfung der Abmessungen und der Rechtwinkligkeit von Trbltten This standard was accepted by CEN as a European Standard on30 December1974 whereby the members committed to accord to it t

10、he status of a national standard must do so without change. The details of the conditions under which members are so committed are given in the CEN constitution. Up-to-date lists of national standards organizations which have adopted this European Standard, and relevant bibliographical references, m

11、ay be obtained on application to the CEN Central Secretariat or to the sales office of any CEN member. This European Standard exists in three versions (French, English, German), recognized by CEN as equivalent. National versions in other languages rank as translations, and in case of doubt should be

12、 checked against one of the recognized versions (French, English, German). CEN members are the national standards organizations of Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and United Kingdom. CEN European Committe

13、e for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat:5 Boulevard de IEmpereur B-1000 Bruxelles Copyright reserved to all national CEN membersEN25:1975 BSI 03-1999 2 Brief history European Standard EN25 was drawn up by working group CEN/WG33 “Technol

14、ogical tests for doors, windows, fastenings and their building hardware”, the secretariat of which is held by AFNOR. It is the second of a series applicable to doors. Work on it was undertaken in June1971 by the group of experts EG3 “Door tests” created in February1971 by the working group, and the

15、method was accepted in1972 by CEN/WG33. This European Standard was adopted by CEN on30 December1974, on the strength of its acceptance by the following member countries: Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Italy, Netherlands, Norway, Spain, Switzerland and United Kingdom. C

16、ontents Page Brief history 2 1 Scope 3 2 Field of application 3 3 Principle of the method 3 4 Operating method 3 5 Accuracy of measurement 3 6 Statement of results 3 Figure 1 Door leaf measurements 3EN 25:1975 BSI 03-1999 3 1 Scope The present standard determines the method which has to be used to m

17、easure the dimensions and the defects of squareness of door leaves. 2 Field of application This standard can be applied to all doors which are nominally flat and rigid. 3 Principle of the method The measurement of dimensions and of the defects of squareness of a door leaf consist in taking: 4 Operat

18、ing method 4.1 Measurement of height. The height is measured along the lines aa and bb (see Figure 1) parallel to and not more than20mm from the two longitudinal edges. 4.2 Measurement of width. The width is measured along the lines cc and dd (see Figure 1) parallel to and not more than20mm from the

19、 transverse edges. 4.3 Measurement of thickness. The thickness is measured at6points located approximately20mm from the edges and at the positions indicated on Figure 1. 4.4 Measurement of defects of squareness. The deviation from squareness of adjacent edges of the door leaf is determined at all fo

20、urs corners of the door leaf with a square with arms500mm long. 5 Accuracy of measurement The height and width are to be measured with a maximum uncertainty of 0.5mm. The thickness and deviation from squareness are to be measured with a maximum uncertainty of 0.1mm. 6 Statement of results The result

21、s of all the measurements are to be noted in the report. The height and width are to be rounded to the nearest millimetre. The thickness and deviation from squareness are to be expressed in millimetres to one place of decimals. a) at one face, measurements of height and width; b) at the indicated po

22、ints, measurements of thickness; c) at the four corners, measurements of deviation from squareness; Figure 1 Door leaf measurementsblankBS5278:1976 BSI 03-1999 National appendix A The United Kingdom participation in the preparation of this European Standard came under the authority of the Building D

23、ivisional Council. The following organizations were involved in the work on this standard: Aluminium Window Association Association of Builders Hardware Manufacturers British Plastics Federation British Woodwork Manufacturers Association Department of the Environment, Building Research Establishment

24、 Department of the Environment, Housing and Construction Department of the Environment, Property Services Agency Fibre Building Board Development Organization Ltd. Flat Glass Manufacturers Association Greater London Council Incorporated Association of Architects and Surveyors Institution of Fire Eng

25、ineers Interdepartmental Construction Development Group Metal Window Federation of Great Britain Modular Society Royal Institute of British Architects Timber Research and Development AssociationBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

26、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standa

27、rds. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the consta

28、nt aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:

29、 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Custom

30、er Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informat

31、ion on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996

32、 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in a

33、ll BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means e

34、lectronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.