BS 5131-3 4-1978 Methods of test for footwear and footwear materials - Uppers textiles and threads - Edgewise compressibility upper materials《鞋靴和鞋靴材料试验方法 第3部分 鞋帮、织物和缝线 第 4节 垂直于针脚孔的.pdf
《BS 5131-3 4-1978 Methods of test for footwear and footwear materials - Uppers textiles and threads - Edgewise compressibility upper materials《鞋靴和鞋靴材料试验方法 第3部分 鞋帮、织物和缝线 第 4节 垂直于针脚孔的.pdf》由会员分享,可在线阅读,更多相关《BS 5131-3 4-1978 Methods of test for footwear and footwear materials - Uppers textiles and threads - Edgewise compressibility upper materials《鞋靴和鞋靴材料试验方法 第3部分 鞋帮、织物和缝线 第 4节 垂直于针脚孔的.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS5131-3.4: 1978 Methods of Test for footwear and footwear materials Part3: Uppers, textiles and threads Section3.4 Edgewise compressibility, upper materials NOTEIt is recommended that this Section should be read in conjunction with the information in the General introduction to BS5
2、131, published separately. UDC 685.31:620.1:685.312.142.2:539.411BS5131-3.4:1978 This British Standard, having been prepared under the directionof the Clothing Standards Committee, was published under the authority ofthe Executive Board on 31May1978 BSI 12-1999 The following BSI references relate to
3、 the work on this standard: Committee reference CLT/7 Draft for comment76/35887 DC ISBN 0 580 10226 2 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standar
4、d does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated
5、 in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue CommentsBS5131-3.4:1978 BSI 12-1999 i Contents Page 1 Scope 1 2 Principle 1 3 Apparatus 1 4 Conditioning and testing atmosphere 1 5 Test pieces 1 6 Procedure 1 7 Expression of results 1 8 Te
6、st report 2 Figure 1 Positioning the test piece 2 Figure 2 Bending of the test piece 2 Figure 3 Wrinkling of the test piece 2ii blankBS5131-3.4:1978 BSI 12-1999 1 1 Scope This Section describes a method for measuring the extent to which upper materials will shorten or compress in an edgewise directi
7、on without forming pleats or wrinkles. This ability to accept compression is one of the factors that determines how cleanly the toe of the upper can be lasted. This method is applicable to all upper materials, but is most useful when comparing materials of the same basic type. NOTESection3.4 is base
8、d on SATRA 1)Physical test methodPM44. 2 Principle A test piece is supported in a horizontal plane by two clamps, one fixed and one movable. The movable clamp is moved towards the other causing the test piece to bend. A flat, transparent, rigid plastics bar is pressed down on the bent portion of the
9、 test piece and the degree of wrinkling, as viewed through this bar, is assessed. 3 Apparatus The following apparatus is required. 3.1 An instrument capable of clamping a test piece in a horizontal plane, with one fixed clamp and one movable along a fixed scale. NOTEThe SATRA Wrinkleometer STD119, s
10、hown in Figure 1 toFigure 3, is suitable. 3.2 Transparent rigid plastics bar,24mm to25mm wide. 3.3 The test piece is held in position on the base of the instrument by two screw clamps (seeFigure 1). One of the clamps (B) is in a fixed position on the base while the other (A) may be moved laterally r
11、elative to the base, the amount of movement being shown by a scale. This allows the two clamps to be tightened on to the test piece a known distance apart and then clamp A is moved back to its original or zero position thus bending the test piece as shown in Figure 2. The separation of the two clamp
12、s in the zero position is25mm. 4 Conditioning and testing atmosphere Condition the test pieces for48h at20 2 C and652% relative humidity and carry out the test in this atmosphere. 5 Test pieces Cut one strip25mm wide and approximately150mm long in each principal direction. 6 Procedure 6.1 Unscrew cl
13、amps A and B and slide the test piece into position underneath them, then clamp the test piece with clamp B. Unscrew the wing nut on the base and move clamp A to bring a suitable scale reading in line with the reference mark on the base. The scale is marked from0mm to8mm in steps of1mm and the4mm re
14、ading is usually a suitable starting point for the test. Tighten the wing nut. 6.2 Screw down clamp A so that the portion of the test piece between the two clamps is flat. Unscrew the wing nut and slide clamp A as far as possible towards clamp B, i.e.until the scale zero and reference mark align, an
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS5131341978METHODSOFTESTFORFOOTWEARANDFOOTWEARMATERIALSUPPERSTEXTILESANDTHREADSEDGEWISECOMPRESSIBILITYUPPERMATERIALS

链接地址:http://www.mydoc123.com/p-544884.html