BS 509-1-1987 Acetone for industrial use - Specification for acetone《工业用丙酮 第1部分 丙酮规范》.pdf

《BS 509-1-1987 Acetone for industrial use - Specification for acetone《工业用丙酮 第1部分 丙酮规范》.pdf》由会员分享，可在线阅读，更多相关《BS 509-1-1987 Acetone for industrial use - Specification for acetone《工业用丙酮 第1部分 丙酮规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD CONFIRMED APRIL 1993 BS 509-1: 1987 Acetone for industrial use Part 1: Specification for acetone UDC 661.727.4:543.06BS509-1:1987 This British Standard, having been prepared under the directionof the Chemicals Standards Committee, was published under the authority ofthe Board of BSI

2、 and comes intoeffect on 30 January 1987 BSI07-1999 The following BSI references relate to the work on this standard: Committee reference CIC/51 Draft for comment 85/50952 DC ISBN 0 580 15566 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted by

3、 the Chemicals Standards Committee (CIC/-) to Technical Committee CIC/51, upon which the following bodies were represented: British Pharmacopoeia Commission British Society of Perfumers Chemical Industries Association Department of Trade and Industry (Laboratory of the Government Chemist) Royal Soci

4、ety of Chemistry Amendments issued since publication Amd. No. Date of issue CommentsBS509-1:1987 BSI 07-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Description 1 3 Sampling and size of sample 1 4 Colour 1 5 Density 1 6 Distillation range 1 7 Residue on evap

5、oration 1 8 Water content 1 9 Acidity 1 10 Alkalinity 1 11 Permanganate test 1 12 Alcoholic impurities 1 13 Miscibility with water 1 Publications referred to Inside back coverBS509-1:1987 ii BSI 07-1999 Foreword This Part of BS 509, which has been prepared under the direction of the Chemicals Standa

6、rds Committee, comprises a specification for acetone to meet the requirements of a wide range of industrial users. First published in 1933, BS 509 was last revised in 1971 and was subsequently amended to become BS 509-1. In this revision of BS 509-1, the requirements for distillation range, water co

7、ntent and the permanganate test have been made more stringent and the requirement for relative density has been replaced by one for density at 20 C. A requirement for miscibility with water is now included. In addition, the test methods associated with the specification are now published separately

8、as BS 509-2. This standard supersedes BS 509-1:1971, which is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer i

9、mmunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in t

10、he amendment table on the inside front cover.BS509-1:1987 BSI 07-1999 1 1 Scope This British Standard specifies requirements for acetone suitable for industrial purposes. NOTEThe titles of the publications referred to in this standard are listed on the inside back cover. 2 Description The material s

11、hall be clear and free from matter in suspension, as assessed by visual inspection, and shall consist essentially of acetone, CH 3 COCH 3 . 3 Sampling and size of sample A sample of not less than 1 L shall be taken in accordance with BS 509-2. 4 Colour The colour of the material shall not exceed 10

12、Hazen units when measured as described in BS 5339. 5 Density The density of the material at 20 C shall be not lower than 0.789 g/mL and not higher than 0.791 g/mL when determined as described in BS 4522. 6 Distillation range When the material is distilled as described in BS4591, modified as specifie

13、d in BS 509-2, the initial boiling point at 1 013 mbar 1)pressure shall be not lower than 55.8 C and the dry point at1013mbar pressure shall be not higher than56.6 C. 7 Residue on evaporation The residue on evaporation of the material shall not exceed 0.001% (m/m) when determined as described in BS

14、4524. 8 Water content The material shall not contain more than 0.30 % (m/m) of water when determined as described in clause 4 of BS 2511:1970, modified as described in BS 509-2, using 20 mL of the material. 9 Acidity The material shall not contain more than0.002%(m/m) of acid, calculated as acetic a

15、cid (CH 3 COOH) and determined as described in BS509-2. 10 Alkalinity The material shall not show any alkalinity when tested as described in BS 509-2. 11 Permanganate test The material shall not completely discharge the permanganate colour within 180 min when tested as described in BS 509-2. 12 Alco

16、holic impurities The material shall not show any alcoholic impurities when tested as described in BS 509-2. 13 Miscibility with water The material shall not show opalescence when tested as described in BS 509-2. 1) 1 mbar = 100 N/m 2= 100 Pa.2 blankBS509-1:1987 BSI 07-1999 Publications referred to B

17、S 509, Acetone for industrial use. BS 509-2, Methods of test. BS 2511, Methods for the determination of water (Karl Fischer method). BS 4522, Method for the determination of density of liquids at 20 C. BS 4524, Method for the determination of residue on evaporation on a water bath. BS 4591, Method f

18、or the determination of distillation characteristics. BS 5339, Method of measurement of colour in Hazen units (platinum-cobalt scale) of liquid chemical products. BS 509-1: 1987 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible f

19、or preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or ed

20、itions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the i

21、nside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be ad

22、dressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range o

23、f information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02

24、089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all

25、 BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means elec

26、tronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.