BS 508-1-1986 Butan-1-ol for industrial use - Specification for butan-1-ol《工业用丁醇 第1部分 丁醇规范》.pdf

《BS 508-1-1986 Butan-1-ol for industrial use - Specification for butan-1-ol《工业用丁醇 第1部分 丁醇规范》.pdf》由会员分享，可在线阅读，更多相关《BS 508-1-1986 Butan-1-ol for industrial use - Specification for butan-1-ol《工业用丁醇 第1部分 丁醇规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 508-1:1986 Butan-1-ol for industrial use Part 1: Specification for butan-1-ol UDC 66.061:661.725.4:547.264BS508-1:1986 This British Standard, having been prepared under the directionof the Chemicals Standards Committee, was published under the authority ofthe BoardofBSIandcomes i

2、ntoeffecton 30September1986 BSI 11-1999 First published October 1933 First revision March 1950 Second revision December 1956 Third revision July 1966 Fourth revision September 1986 The following BSI references relate to the work on this standard: Committee reference CIC/51 Draft for comment 85/50951

3、 DC ISBN 0 580 15339 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Chemicals Standards Committee (CIC/-) to Technical Committee CIC/51, upon which the following bodies were represented: British Pharmacopoeia Commission British Societ

4、y of Perfumers Chemical Industries Association Department of Trade and Industry (Laboratory of the Government Chemist) Royal Society of Chemistry Amendments issued since publication Amd. No. Date of issue CommentsBS508-1:1986 BSI 11-1999 i Contents Page Committees responsible Inside front cover Fore

5、word ii 1 Scope 1 2 Description 1 3 Sampling and size of sample 1 4 Colour 1 5 Density 1 6 Distillation range 1 7 Water content 1 8 Residue on evaporation 1 9 Acidity 1 10 Aldehydes and ketones 1 Publications referred to Inside back coverBS508-1:1986 ii BSI 11-1999 Foreword This Part of BS508, which

6、 has been prepared under the direction of the Chemicals Standards Committee, comprises a specification for butan-1-ol to meet the requirements of a wide range of industrial users. BS 508 was first published in1933 and last revised in1966. In the present edition, the requirements for distillation ran

7、ge and water content have been made more stringent. The requirement for flash point has been deleted and the requirement for relative density has been replaced by one for density at20 C. In addition, the test methods associated with the specification are now published separately as BS508-2. This sta

8、ndard supersedes BS508-1:1966, which is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obl

9、igations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on t

10、he inside front cover.BS508-1:1986 BSI 11-1999 1 1 Scope This Part of BS508 specifies requirements for butan-1-ol suitable for industrial purposes. NOTEThe titles of the publications referred to in this standard are listed on the inside back cover. 2 Description The material shall be clear and free

11、from matter in suspension, as assessed by visual inspection, and shall consist essentially of butan-1-ol, CH 3 CH 2 CH 2 CH 2 OH. 3 Sampling and size of sample A sample of not less than1 L shall be taken in accordance with BS508-2. 4 Colour The colour of the material shall not exceed15 Hazen units w

12、hen measured by the method described in BS5339. 5 Density The density of the material at20 C shall be not lower than0.809g/mL and not higher than0.811g/mL when determined by the method described in BS4522. 6 Distillation range When the material is distilled by the method described in BS4591, modifie

13、d as specified in BS508-2, the initial boiling point at1 013mbar 1)pressure shall be not below116.5 C and the dry point at1 013 mbar pressure shall be not above119.0 C. 7 Water content The material shall not contain more than0.10%(m/m) of water when determined by the method described in clause 2 of

14、BS2511:1970, using20 mL of the material. 8 Residue on evaporation The residue on evaporation of the material shall not exceed0.005%(m/m) when determined by the method described in BS4524. 9 Acidity The material shall not contain more than0.005%(m/m) of acid, calculated as butyric acid (C 3 H 7 COOH)

15、 and determined by the method described in BS508-2. 10 Aldehydes and ketones The material shall not contain more than0.20%(m/m) of aldehydes and ketones, calculated as butyraldehyde (C 3 H 7 CHO) and determined by the method described in BS508-2. 1) 1mbar=100 N/m 2 =100Pa.2 blankBS508-1:1986 BSI 11-

16、1999 Publications referred to BS 508, Butan-1-ol for industrial use. BS 508-2, Methods of test. BS 2511, Methods for the determination of water (Karl Fischer method). BS 4522, Method for the determination of density of liquids at20 C. BS 4524, Method for determination of residue on evaporation on a

17、water bath. BS 4591, Method for the determination of distillation characteristics. BS 5339, Method of measurement of colour in Hazen units (platinum-cobalt scale) of liquid chemical products. BS 508-1:1986 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent

18、 national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess

19、 the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of

20、 which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standar

21、ds publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards

22、 BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Cen

23、tre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyrig

24、ht Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in

25、any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.