BS 4973-3-1976 Interlinings - Woven and knitted fusible interlinings《衬里规范 第3部分 机织和针织热融衬里》.pdf

《BS 4973-3-1976 Interlinings - Woven and knitted fusible interlinings《衬里规范 第3部分 机织和针织热融衬里》.pdf》由会员分享，可在线阅读，更多相关《BS 4973-3-1976 Interlinings - Woven and knitted fusible interlinings《衬里规范 第3部分 机织和针织热融衬里》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4973-3: 1976 Specification for Interlinings Part 3: Woven and knitted fusible interlinings UDC 687.182:687.152.076:677.064:677.066.6BS4973-3:1976 This British Standard, having been prepared under the directionof the Linen Standards Committee was published underthe authority of th

2、e Executive Board on 30April1976 BSI 12-1999 The following BSI references relate to the work on this standard: Committee referenceLIT/7/1 Draft for comment74/35950DC and draft for approval75/35640 ISBN 0 580 09392 1 Co-operating organizations The Linen Standards Committee, under whose supervision th

3、is British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: Belfast Public Textile Testing and Conditioning House Central Council of Irish Linen Industry Clothing Institute Department of the Environment Departme

4、nt of Health and Social Security Flaxspinners and Manufacturers Association of Great Britain Flaxspinners Association Ltd. of Northern Ireland Irish Linen Merchants Association Irish Power Loom Manufacturers Association Lambeg Industrial Research Association Linen Sewing Thread Manufacturers Associa

5、tion Ministry of Commerce Northern Ireland Ministry of Defence* Society of Dyers and Colourists Textile Institute Textile Research Council The Government department marked with an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the p

6、reparation of this British Standard: Association of Municipal Corporations British Nonwoven Manufacturers Association British Railways Board Clothing Manufacturers Federation Dyers and Cleaners Research Organization Institute of Purchasing and Supply Manchester Fire Brigade Textile Clothing Contract

7、ors Association Individual experts Amendments issued since publication Amd. No. Date of issue CommentsBS4973-3:1976 BSI 12-1999 i Contents Page Co-operating organizations Inside front cover Foreword ii 1 Scope 1 2 References 1 3 Definitions 1 4 Fusing 1 5 Technical requirements 1 6 Marking 2 Table 1

8、 Technical requirements 1 Table 2 Uses 2 Publications referred to Inside back coverBS4973-3:1976 ii BSI 12-1999 Foreword A comprehensive range of traditional fabric constructions is contained in BS4560 “Linings and interlinings for uniform clothing”. User trials by hospital and fire brigade staffs h

9、ave encouraged the adoption of a specification for non-traditional constructions. The latter are being published as Parts of BS4973 as follows. Part 1: Nonwoven sew-in interlinings; Part 2: Nonwoven fusible interlinings; Part 3: Woven and knitted fusible interlinings. It is intended that the fabrics

10、 in this standard should be used in conjunction with the outer cloths specified in BS1771 “Outdoor uniform cloths for fire service, local authority and hospital staffs”. Certification. Attention is drawn to the certification facilities described on the inside back cover of this standard. A British S

11、tandard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cov

12、er, an inside front cover, pagesi andii, pages1and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS4973-3:1976 BSI 12-1999 1 1 Scope This

13、Part of this British Standard specifies requirements for woven and knitted fusible interlinings for uniform clothing for large users such as Government departments, fire services, hospitals and local authorities. Technical requirements are given inTable 1 and the materials are listed inTable 2 accor

14、ding to the garments for which they are recommended. 2 References The titles of the British Standards referred to in this standard are listed on the inside back cover. 3 Definitions For the purposes of this Part of this British Standard the following definitions apply. 3.1 strike-through penetration

15、 of the adhesive from the interlining to the face of the outer fabric 3.2 strike-back penetration of the adhesive to the outer surface of the interlining 4 Fusing Fusing instructions shall be supplied with the interlining and these shall be followed exactly by the maker-up. There shall be no strike-

16、through, and strike-back shall not be such as to cause subsequent adhesion to the lining and/or pocketing. Allow at least24h to elapse between fusing operations and carrying out tests. 5 Technical requirements 5.1 The mass per unit area of the fusible interlining most suitable for use with the outer

17、 fabric shall be agreed between the purchaser and the manufacturer and shall be within one of the ranges given inTable 1. The mass per unit area so agreed shall be subject to a tolerance of 10%. 5.2 Resistance to dry cleaning of the laminate bond (i.e.outer fabric plus interlining) shall be assessed

18、 by subjecting each specimen three times to the treatment described in BS4961, which gives two methods of test for dry cleaning (including steam finishing). The laboratory procedure is intended primarily for screening and control testing and in cases of dispute the machine procedure shall be used. 5

19、.3 Dimensional change on cold water immersion shall be limited as shown inTable 1. 5.4 To withstand normal handling tensile strength in the warp direction shall be not less than that shown inTable 1. 5.5 Peel bond strengths vary according to the construction of the outer fabric and type of finish th

20、e cloth has received. It is not practicable to specify a minimum strength that will be adequate for all the fabrics listed in BS1771. It is therefore recommended for quality control purposes that the peel bond strength shall be as agreed between the purchaser and the supplier, according to the speci

21、fic fabric and fusing method involved. A method for determination of peel bond strength is given inAppendixA ofBS4973-2:1973. Table 1 Technical requirements Property Test method Performed on a Compliance requirement FWK1 FWK2 FWK3 FWK4 Mass/unit area (g/m 2 ) BS2471 I 70to120 120to150 150to200 200to

22、340 Resistance to dry cleaning BS4961 L No delamination of the interlining from the outer fabric and no appreciable change in handle Dimensional change on cold water immersion (%max.) BS4736 I 2 2 2 2 Minimum tensile strength in warp direction(N/5cm strip) BS2576 I 100 100 100 100 a I=interliningL=l

23、aminateBS4973-3:1976 2 BSI 12-1999 5.6 For purposes of general comparison in respect of handle not specified in this British Standard, agreement shall be reached between the purchaser and the supplier. There shall be no appreciable change in handle of the laminate after dry cleaning. 6 Marking Each

24、interlining in the finished state shall be identified with the British Standard reference number, either by stamping or by labelling the tag-end of the piece. Table 2 Uses a a) Lightweight jackets of fabric up to410g/m 2 : Foreparts FWK1, FWK2 Cuffs FWK1, FWK2 Stays FWK1 b) Jackets of fabric over410

25、g/m 2 : Foreparts FWK2, FWK3 Chest reinforcements FWK2, FWK3, FWK4 Cuffs FWK2, FWK3 Stays FWK1, FWK2 c) Overcoats: Foreparts FWK2, FWK3 Chest reinforcements FWK3, FWK4 Stays FWK2, FWK3 Collars FWK2, FWK3 Belts FWK2, FWK3, FWK4 d) Raincoats: Foreparts FWK1, FWK2, FWK3 Chest reinforcements FWK1, FWK2,

26、 FWK3, FWK4 Stays FWK1, FWK2 Collars FWK1, FWK2, FWK3 Flaps, welts, etc. FWK1, FWK2, FWK3 Belts FWK1, FWK2, FWK3 a These recommendations are for guidance only and do not prohibit the use of the various interlinings for other purposes if so desired.BS4973-3:1976 BSI 12-1999 Publications referred to T

27、his standard makes reference to the following British Standards: BS 1771, Outdoor uniform cloths for fire service, local authority and hospital staffs. BS 2471, Methods of test for the mass per unit length and per unit area of woven or knitted fabrics. BS 2576, Methods for the determination of break

28、ing load and extension of strips of woven textile fabric. BS 4736, Method of test for the determination of dimensional changes of fabrics by cold water immersion. BS 4961, Method for determination of dimensional stability of textiles to dry cleaning in perchloroethylene. BS 4973, Interlinings. BS 49

29、73-2, Nonwoven fusible interlinings. BSI Certification Trade Mark The Kitemark The Kitemark is the registered certification trade mark of the British Standards Institution. A licence to use the Kitemark on or in relation to a product will be granted to any manufacturer or producer who demonstrates t

30、hat he can and will be able consistently to make that product to a specified British Standard. His capability of doing so is initially assessed by inspection of his production process, quality control organization and test facilities, and by independent testing of a sample of the product against all

31、 the criteria of the relevant standard. The licensee is required to accept, and to operate in accordance with, a BSI scheme of supervision and control which identifies the tests to be carried out during manufacture and on the completed product, and specifies the frequency of such testing. BSI carrie

32、s out unannounced inspection visits to the manufacturers works and audit testing of the product, and may withdraw the licence for any failure of the manufacturer to comply with the relevant standard or with the requirements of the scheme of supervision and control. The presence of the Kitemark on or

33、 in relation to a product is an assurance that the goods have been produced under a system of supervision, control and testing, operated during manufacture and including periodical inspection of the manufacturers works in accordance with the certification mark scheme ofBSI. Further particulars of th

34、e terms of licence may be obtained from the Quality Assurance Department, British Standards Institution, Maylands Avenue, Hemel Hempstead, Herts. HP24SQ.BS 4973-3: 1976 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for prepar

35、ing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. I

36、t is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside fro

37、nt cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed t

38、o Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of informa

39、tion on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048

40、. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publ

41、ications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic,

42、photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.