BS 4896-1973 Method for the determination of ash of pulp《纸浆灰分测定方法》.pdf

《BS 4896-1973 Method for the determination of ash of pulp《纸浆灰分测定方法》.pdf》由会员分享，可在线阅读，更多相关《BS 4896-1973 Method for the determination of ash of pulp《纸浆灰分测定方法》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4896:1973 Method for The determination of ash of pulp UDC 676.014.2:543.822BS4896:1973 This British Standard, having been approved by the Paper Industry Standards Committee,was published underthe authorityof the Executive Boardon 7December1973 BSI 12-1999 The following BSI refere

2、nces relate to the work on this standard: Committee reference PAC/11 Draft for comment 71/53903 ISBN 0 580 07660 1 Co-operating organizations The following is a list of members of the Paper Industry Standards Committee, who have had the preparation of this British Standard under consideration: The f

3、ollowing is a list of members of the Technical Committee on Methods of Test for Paper, Board and Pulp, the Committee actually responsible for the preparation of this British Standard: Chairman: Mr H.R. Hutley Mr S. Bailey Mr Gilbert A. Smith National Association of Paper Merchants British Federation

4、 of Master Printers Dr N.K. Bridge Mr R.W.H. Bray, A.F.C. PIRA (Research Association for the Paper and Mr.J. Harding Board, Printing and Packaging Industries) British Paper and Board Makers Dr J.F. Heggie Association (Incorporated) Royal Institute of Public Health and Hygiene Mr J. Leather Mr R.L. B

5、allard British Railways Board Mr J.F.A. Rankin Mr C. Sumner Dr M.N. Strachan Mr A.D.P. Tanner Mr G. Thompson Envelope Makers and Manufacturing Technical Section of the British Paper and Stationers Association Board Makers Association Mr F.E. Ashman H.M. Stationery Office Chairman: Mr H.R. Hutley Mr

6、G.R. Keay Dr George L. Fuchs Mr C. Sumner Mr J. Strode Envelope Makers and Manufacturing British Federation of Master Printers Stationers Association Mr M.R. Hadfield Mr J.A. Moore British Paper and Board Makers Fibreboard Packing Case Manufacturers Association (Incorporated) Association Mr E.C. All

7、ison Mr W.J.R. Howell Mr M.J. Ford H.M. Stationery Office British Wood Pulp Association Mr J.W. More Mr E.D. Garner Man-made Fibre Producers Committee Chemical Industries Association Mr C.F. Finney Mr H.F. Church Ministry of Defence, Army Department Electrical Research Association Mr J.A. Simmons Mr

8、 D. Horton Post Office Mr R.J. Hamer Mr R. Peerless Mr F.D. Munday Mr J.F.A. Rankin PIRA (Research Association for the Paper andDr M.N. Strachan Board, Printing and Packaging Industries) Mr S.A. Underwood Mr H.A. Idle Technical Section of the British Paper and Society of British Printing Ink Manufac

9、turers Board Makers Association Mr R.L. Ballard Mr E. Mytum Mr J.D. Batley Textile Institute Mr R.A. Beveridge Mr P. Howarth Mr F.A. Guttfield University of Manchester Mr F.J.T. Harris Mr W.D.L. Anderson Mr I.F. Hendry Technical Committee DPE/2, Punched Cards, Mr L.F. Hopkins Dimensions and Properti

10、es Mr K.A. Hyam Mr C.F. Finney Mr D.J. McConnell Technical Committee DPE/3, Punched Tape, Mr A.P. McDonald Dimensions and Properties Mr E.W. Peacock Amendments issued since publication Amd. No. Date of issue CommentsBS4896:1973 BSI 12-1999 i Contents Page Co-operating organizations Inside front cove

11、r Foreword ii 1 Scope 1 2 Definition 1 3 Apparatus 1 4 Preparation of sample 1 5 Procedure 1 6 Expression of results 1 7 Test report 1 Publication referred to 2BS4896:1973 ii BSI 12-1999 Foreword There has for some years been a series of British Standards for the testing of paper and board; where th

12、ere is a corresponding Recommendation or Standard ofthe International Organization for Standardization (ISO), the British Standard is usually in line with the international decisions. More recently, the ISO Committee concerned has undertaken a considerable amount of work on the testing of pulp for u

13、se in the papermaking, plastics, textile and other industries, and the United Kingdom has taken an active part in this work. Some of the methods are of use to all pulp users, while others may concern only certain converting interests. After consultation with the various industries concerned it was d

14、ecided that the potential value of these methods was sufficient to warrant their publication as British Standards, and several have already been issued. As a matter of organizational convenience, this British Standard method, which, apart from minor editorial adjustments, follows ISO Recommendation

15、R1762, “Pulps. Determination of ash” precisely, is published under the authority of the Paper Industry Standards Committee, but the other relevant industries have all been consulted. In the course of its work, the ISO Committee made a statistical study of the determination of ash and of sulphated as

16、h of many different types of pulp. It was proved that neither method showed any significant advantage over the other. Therefore, the more simple ash method was chosen. The determination of acid-insoluble ash of pulp is dealt with in BS4496, “Method for the determination of acid-insoluble ash in pulp

17、”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document compris

18、es a front cover, an inside front cover, pagesi andii, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS4896:1973 BSI 12-1999 1 1

19、 Scope This British Standard specifies a method for the determination of ash of pulp. The “ash content” of pulp gives an estimation of its content of mineral salts and other inorganic matter, but is not quantitatively equal to this content. The method applies to all kinds of papermaking and dissolvi

20、ng pulps. NOTEThe title of the British Standard referred to in this standard is given on page 2. 2 Definition For the purposes of this British Standard, the following definition applies: ash content of a pulp sample the mass of the residue after complete combustion at a temperature of575 25 C under

21、specified conditions and is expressed as a percentage of the mass of the oven-dry sample 3 Apparatus 3.1 Crucibles or dishes of platinum, porcelain or quartz. 3.2 Electric muffle furnace, suitable for maintaining a temperature of575 25 C. 4 Preparation of sample Tear the air-dry sample into pieces o

22、f a suitable size. Do not use cut or punched edges, or other parts where metallic contamination may have occurred. 5 Procedure 5.1 Preparation of test piece. Weigh out, to the nearest0.01g, an amount of pulp that will give not less than10mg of ash. At the same time weigh out a separate test piece fo

23、r dry matter determination in accordance with BS4502. 5.2 Determination. Heat a crucible or dish for15minutes in the muffle furnace at a temperature of575 25 C. Place it in a desiccator and cool for 45 minutes if porcelain or quartz ware is used, or for15minutes if using platinum. Weigh to the neare

24、st0.1mg. If the test piece is of a suitable size, place it in the crucible and burn the pulp over the low flame of a gas burner until it is well carbonized (see Note1). Ifthe crucible or dish is too small to hold the entire test piece, gently burn it off in portions. Take care not to let any ash blo

25、w from the crucible. Then place the crucible in the muffle furnace and ignite at a temperature of575 25 C for a period of3hours, or longer if needed, to burn away all the carbon (seeNote2). When the ignition is complete, as indicated by the absence of black particles, allow to cool as described abov

26、e and weigh to the nearest0.1mg. NOTE 1If a suitable furnace is available for each separate test piece, place the crucible in a cold furnace and heat carefully until the pulp is well carbonized. If a gas burner is used, take care that the inner (reducing) cone of the flame does not come in contact w

27、ith the platinum; adjust the flame so that no carbon deposits are formed on the outside of the crucible or dish. NOTE 2Undue extension of the ignition time may cause unwanted reactions and produce erroneous results. 6 Expression of results Carry out two determinations and calculate the ash content X

28、, as a percentage by mass, by the following formula: Report the result as the mean of the two determinations, to two decimal places. 7 Test report The test report shall state the results obtained and indicate any details that are optional or not specified in this British Standard, as well as any inc

29、idents that may have affected the results. where a is the mass of ash, expressed in grams m is the mass of pulp, calculated on an oven-dry basis, expressed in grams.BS4896:1973 2 BSI 12-1999 Publication referred to This standard makes reference to the following British Standard: BS4502, Method for t

30、he determination of dry matter content of pulp. BS4896:1973 BSI 12-1999 BSI Certification Trade Mark The Kitemark The British Standards Institution is the owner of a registered certification trade mark. It is usually associated with the words “approved to British Standard” as shown below, the number

31、 of the relevant British Standard being added. This mark may be used only by those licensed under the certification mark scheme operated by BSI. The presence of this mark on or in relation to a product is an assurance that the goods have been produced under a system of supervision, control and testi

32、ng, operated during manufacture and including periodical inspection of the manufacturers works in accordance with the certification mark scheme of BSI designed to ensure compliance with a British Standard.BS 4896:1973 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the

33、 independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that

34、they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the

35、 identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and for

36、eign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information

37、on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Inf

38、ormation Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967

39、001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or tra

40、nsmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.