BS 4737-3 3-1977 Intruder alarm systems - Specifications for components - Protective switches《擅入者报警系统 第3部分 元部件规范 第3节 保护开关》.pdf

《BS 4737-3 3-1977 Intruder alarm systems - Specifications for components - Protective switches《擅入者报警系统 第3部分 元部件规范 第3节 保护开关》.pdf》由会员分享，可在线阅读，更多相关《BS 4737-3 3-1977 Intruder alarm systems - Specifications for components - Protective switches《擅入者报警系统 第3部分 元部件规范 第3节 保护开关》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4737-3.3: 1977 Specification for Intruder alarm systems in buildings Part 3: Requirements for detection devices Section 3.3 Protective switches UDC 696.6:654.924.3:621.316.54BS 4737-3.3:1977 This British Standard, having been prepared under the direction of the Electronic Equipme

2、nt Standards Committee, was published under the authority of the Executive Board on 31 May 1977. BSI 12-1998 First published April 1971 First revision May 1977 The following BSI references relate to the work on this standard: Committee reference EEL/27 Draft for comment 74/25542DC ISBN 0 580 09683 1

3、 Cooperating organizations The Electronic Equipment Standards Committee, under whose supervision this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations British Broadcasting Corporation British Electrical a

4、nd Allied Manufacturers Association British Radio Equipment Manufacturers Association Cable Television Association of Great Britain Department of Prices and Consumer Protection Electrical, Electronic, Telecommunication and Plumbing Union Electricity Supply Industry in England and Wales Electronic Co

5、mponents Board Electronic Engineering Association Engineering Equipment Users Association Institution of Electronic and Radio Engineers Post Office Radio and Electronic Component Manufacturers Federation Scientific Instrument Manufacturers Association The organizations marked with an asterisk in the

6、 above list together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Association of Burglary Insurance Surveyors Association of Chief Police Officers British Bankers Association British Insurance Association British Railways Boa

7、rd British Security Industry Association Department of the Environment Home Office Independent Burglar Alarm Association Lloyds Syndicates Survey Department Metropolitan Police Ministry of Defence National Supervisory Council for Intruder Alarms Telecommunication Engineering and Manufacturing Associ

8、ation Amendments issued since publication Amd. No. Date of issue CommentsBS4737-3.3:1997 BSI 12-1998 i Contents Page Cooperating organizations Inside front cover Foreword ii 1 Scope 1 2 References 1 3 Definitions 1 4 Circuit configuration 1 5 Performance 1 6 Environment 1 Standards publications refe

9、rred to Inside back coverBS4737-3.3:1997 ii BSI 12-1998 Foreword This revision of BS 4737 has been prepared under the authority of the Electronic Equipment Standards Committee in order to reflect the technical advances in the industry since the publication of the 1971 edition. It takes account of Am

10、endment Slip No.1, 1972 (AMD1064) and of Amendment Slip No.2, 1973 (AMD1218). It is being published in a number of Sections, as follows. Part 1: Requirements for systems with audible signalling only; Section 1.1: Installation; Section 1.2: Maintenance and records; Part 2: Requirements for systems wi

11、th remote signalling; Section 2.1: Installation; Section 2.2: Maintenance and records. Part 3: Requirements for detection devices, consisting of a number of separate Sections (3.1, 3.2, 3.3 etc.). The specifications for detection devices (including this Section of BS4737) are to be read in conjuncti

12、on with Section1.1 or Section2.1 (as appropriate). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obl

13、igations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table o

14、n theinside front cover.BS 4737-3.3:1977 BSI 12-1998 1 1 Scope This British Standard specifies the general requirements for protective switches to be used in intruder alarm systems in buildings. 2 References The titles of the standards publications referred to in this standard are given on page 2. 3

15、 Definitions For the purposes of this British Standard, the following definition applies in addition to those given in BS4737-2.1. 3.1 protective switch a detection device, associated with a moveable part (such as a door or window) designed to generate an alarm condition when the moveable part is op

16、ened 4 Circuit configuration Each protective switch shall be either a closed-circuit device, or an open-circuit device to which all connections are within the closed circuit and within the same enclosure. In open-circuit protective switches the contacts shall be hermetically sealed. A closed-circuit

17、 protective switch may include, as an additional feature, open-circuit contacts. When installed, it shall not be possible visually to determine the connection of the wiring inside the device from the orientation or otherwise of the wiring to the device. 5 Performance Each protective switch shall ope

18、rate in such a manner that an alarm condition shall be generated when the moveable part is opened in the normal manner prior to the appearance of a clear opening100mm wide. 6 Environment The requirements of this British Standard shall be met by the detector under any combination of the following env

19、ironmental conditions. Temperature: 10C to + 40 C Relative humidity: 10 % to 95 %2 blankBS 4737-3.3:1977 BSI 12-1998 Standards publications referred to BS 4737, Specification for intruder alarm systems in buildings. BS 4737-1, Requirements for systems with audible signalling only. BS 4737-1.1, Insta

20、llation. BS 4737-2, Requirements for systems with remote signalling. BS 4737-2.1, Installation.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

21、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorpora

22、ted by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone f

23、inding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS w

24、hich ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standa

25、rds, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to

26、 Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive subst

27、antial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internatio

28、nal standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This doe

29、s not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.