BS 4737-3 12-1978 Intruder alarm systems - Specifications for components - Beam interruption detectors《擅入者报警系统 第3部分 元部件规范 第12节 射束间断探测器》.pdf

《BS 4737-3 12-1978 Intruder alarm systems - Specifications for components - Beam interruption detectors《擅入者报警系统 第3部分 元部件规范 第12节 射束间断探测器》.pdf》由会员分享，可在线阅读，更多相关《BS 4737-3 12-1978 Intruder alarm systems - Specifications for components - Beam interruption detectors《擅入者报警系统 第3部分 元部件规范 第12节 射束间断探测器》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4737-3.12: 1978 Reprinted, incorporating Amendment No. 1 Specification for Intruder alarm systems in buildings Part 3: Requirements for detection devices Section 3.12 Beam interruption detectors UDC 696.6:654.924.32:535.2BS4737-3.12:1978 This British Standard, having been prepare

2、d under the direction of the Electronic Equipment Standards Committee, was published under the authority of the Executive Board on 30 November 1978 BSI 12-1998 First published April 1971 First revision November 1978 The following BSI references relate to the work on this standard: Committee referenc

3、e EEL/27 Draft for comment 74/25543 DC ISBN 0 580 10365 X Cooperating organizations The Electronic Equipment Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the following Government department and scientific and industrial organizations

4、: British Broadcasting Corporation British Electrical and Allied Manufacturers Association British Radio Equipment Manufacturers Association Cable Television Association of Great Britain Department of Prices and Consumer Protection Electrical, Electronic, Telecommunication and Plumbing Union Electri

5、city Supply Industry in England and Wales Electronic Components Board Electronic Engineering Association* Engineering Equipment Users Association Institution of Electronic and Radio Engineers Post Office* Radio and Electronic Component Manufacturers Federation Scientific Instrument Manufacturers Ass

6、ociation The organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Association of Burglary Insurance Surveyors Association of Chief Police Officers British Insurance As

7、sociation British Railways Board British Security Industry Association Department of the Environment Home Office Independent Burglar Alarm Association Lloyds Syndicates Survey Department Metropolitan Police Ministry of Defence National Supervisory Council for Intruder Alarms Telecommunication Engine

8、ering and Manufacturing Association The Committee of London Clearing Bankers on behalf of the Committee of Scottish Clearing Bankers, Co-operative Bank, Central Trustee Savings Bank and Yorkshire Bank Amendments issued since publication Amd. No. Date of issue Comments 3256 March 1980 Clause 11 delet

9、edBS4737-3.12:1978 BSI 12-1998 i Contents Page Foreword ii 1 Scope 1 2 References 1 3 Definition 1 4 Range and beam angle requirements 1 5 Signal processing 1 6 Modulation 1 7 Power supply 1 8 Environment 1 9 Interference 1 10 Anti-tamper device 1 Standards publications referred to Inside back cover

10、BS4737-3.12:1978 ii BSI 12-1998 Foreword This revision of BS 4737 has been prepared under the direction of the Electronic Equipment Standards Committee to reflect the technical advances in the industry since the publication of the 1971 edition. It takes account of AmendmentNo.1,1972 (AMD1064) and of

11、 Amendment No.2,1973 (AMD1218). It is being published in a number of separate Sections, as follows. Part 1: Requirements for systems with audible signalling only; Section 1.1: Installation; Section 1.2: Maintenance and records. Part 2: Requirements for systems with remote signalling; Section 2.1: In

12、stallation; Section 2.2: Maintenance and records. Part 3: Requirements for detection devices, consisting of a number of separate Sections(3.1to3.14). The specifications for detection devices (including this Section of BS4737) are to be read in conjunction with Section1.1 or Section2.1, as appropriat

13、e. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document compris

14、es a front cover, an inside front cover, pages i and ii, pages1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.BS4737-3.12:1978 BSI 12-1

15、998 1 1 Scope This British Standard specifies the general requirements for beam interruption detectors to be used in intruder alarm systems in buildings. 2 References The titles of the standards publications referred to in this standard are listed on the inside back cover. 3 Definition For the purpo

16、ses of this British Standard, the following definition applies in addition to those given in BS4737-1.1 and/or BS 4737-2.1. beam interruption detector. a detection device designed to generate an alarm condition when a beam of radiation between a transmitter and a receiver is completely interrupted.

17、4 Range and beam angle requirements 4.1 Range. The range shall be the greatest separation between the transmitter and the receiver at which an alarm condition is not generated as a result of a 50% reduction in the power level of the signal received. 4.2 Beam angle. The manufacturer shall state both

18、the dimensions of the transmitted beam over which the receiver will satisfy4.1 and the polar diagram of the receiver. 5 Signal processing The detector shall generate an alarm condition of at least 800ms duration as a result of the complete interruption of the signal received for any period longer th

19、an 40ms. The detector shall not generate an alarm condition as a result of the complete interruption of the signal received for any period shorter than 20ms. 6 Modulation The detector shall incorporate some method of modulation such that the introduction of an unmodulated source of wavelength compar

20、able with that of the transmitter shall not prevent an alarm condition being generated or shall generate an alarm condition. 7 Power supply An alarm condition shall be generated if the voltage of the power supply to the detector is reduced sufficiently to impair the performance of the detector. 8 En

21、vironment The requirements of this British Standard shall be met by the detector under any combination of the following environmental conditions. 9 Interference The detector shall be adequately protected against any externally-generated radio-frequency interference and/or mains-borne interference wh

22、ich may normally be expected to occur within the working environment. 10 Anti-tamper device The detector shall be so designed that opening its container by the normal means of access shall operate an anti-tamper device. Temperature: 0 C to 40 C Relative humidity: 10 % to 90 %2 blankBS4737-3.12:1978

23、BSI 12-1998 Standards publications referred to BS 4737, Specification for intruder alarm systems in buildings. BS 4737-1, Requirements for systems with audible signalling only. BS 4737-1.1, Installation. BS 4737-1.2, Maintenance and records 1) . BS 4737-2, Requirements for systems with remote signal

24、ling. BS 4737-2.1, Installation. BS 4737-2.2, Maintenance and records 1) . BS 4737-3, Requirements for detection devices 1) . BS 4737-3.1, Continuous wiring. BS 4737-3.2, Foil on glass. BS 4737-3.3, Protective switches. BS 4737-3.4, Radiowave Doppler detectors. BS 4737-3.5, Ultrasonic movement detec

25、tors. BS 4737-3.6, Acoustic detectors. BS 4737-3.7, Passive infra-red detectors. BS 4737-3.8, Volumetric capacitive detectors. BS 4737-3.9, Pressure mats. BS 4737-3.10, Vibration detectors. BS 4737-3.11, Rigid printed-circuit wiring. BS 4737-3.13, Capacitive proximity detectors. BS 4737-3.14, Delibe

26、rately-operated devices. 1) Referred to in the foreword only.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

27、| | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions Br

28、itish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity

29、while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers auto

30、matically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply th

31、e BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI el

32、ectronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase p

33、rice of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except

34、 as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in th

35、e course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.