BS 4514-2001 Unplasticized PVC soil and ventilating pipes of 82 4 mm minimum mean outside diameter and fittings and accessories of 82 4 mm and of other sizes Specification《82 4mm最小.pdf

《BS 4514-2001 Unplasticized PVC soil and ventilating pipes of 82 4 mm minimum mean outside diameter and fittings and accessories of 82 4 mm and of other sizes Specification《82 4mm最小.pdf》由会员分享，可在线阅读，更多相关《BS 4514-2001 Unplasticized PVC soil and ventilating pipes of 82 4 mm minimum mean outside diameter and fittings and accessories of 82 4 mm and of other sizes Specification《82 4mm最小.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4514:2001 Unplasticized PVC soil and ventilating pipes of 82.4 mm minimum mean outside diameter, and fittings and accessories of 82.4 mm and of other sizes Specification ICS 83.140.30; 91.140.80 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS 4514:2001 Th

2、is British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 July 2001 The following BSI references relate to the work on this British Standard: Committee re

3、ference PRI/88 Draft for comment 00/122010 DC ISBN 0 580 33286 1 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee PRI/88/, Plastic piping systems, to Subcommittee PRI/88/1, Thermoplastic piping systems and components for n

4、on-pressure applications, upon which the following bodies were represented: British Adhesive and Sealants Association British Plastics Federation BSI Testing Services Chartered Institution of Water and Environment Management DETR British Board of Agrement DETR Central Transport Group Department of E

5、nvironment for Northern Ireland Department of Environment, Transport and Waste Institute of Building Control Institute of Plumbing Land Drainage Contractors Association National Association of Plumbing, Heating and Mechanical Services Contractors Plastic Land Drainage Manufacturers Association Scott

6、ish Executive Water Research Centre Plc Amendments issued since publication Amd No. Date CommentBS 4514:2001 BSI 07-2001 i Contents Page Foreword ii 1S c o p e 1 2 Normative references 1 3M a t e r i a l s 2 4A p p e a r a n c e 2 5D i m e n s i o n s 2 6 Physical properties 10 7 Marking 10 8 Testin

7、g requirements 10 Annex A (normative) Weather resistance test 11 Annex B (normative) Proof pressure test for fabricated fittings 12 Bibliography 13 Figure 1 Pipe lengths 3 Figure 2 Location of dimensions and spigots 4 Figure 3 Wall thickness of boss configurations 5 Figure 4 Positions for measuremen

8、t of snap cap wall thickness 6 Figure 5 Typical reducer 6 Figure 6 Typical socket plug 7 Figure 7 Typical groove design 8 Figure 8 Fittings dimensions for design purposes 9 Figure 9 Dimensions of plastics connectors 9 Table 1 Dimensions of pipes 2 Table 2 Configuration of fittings 3 Table 3 Dimensio

9、ns of fittings including integral sockets 5 Table 4 Access dimensions 6 Table 5 Design dimensions of swept fittings 7 Table 6 Stand-off distances 8BS 4514:2001 ii BSI 07-2001 Foreword This revision of this British Standard was entrusted by Technical Committee PRI/88, Plastic piping systems, to Subco

10、mmittee PRI/88/1, Thermoplastic piping systems and components for non-pressure applications. It supersedes the 1983 edition, which is now withdrawn. The major changes between this revision and the previous edition as amended are as follows. a) The conventional products of the 36, 43, 56, 110 and 160

11、 sizes have been withdrawn as these products are now covered by BS EN 1329-1:2000. b) Where possible, reference has been made to the methods of test as described in BS EN 1329-1:2000. Attention is drawn to the provisions of the Health and Safety at Work etc. Act 1974 1, and the need to ensure that a

12、ppropriate precautions are taken to ensure the safety of personnel when carrying out the methods of test required by this standard. Annex A and Annex B are normative. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible

13、 for the correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i to ii, pages 1 to 13 and a back cover. The BSI copyright notice displayed in this documen

14、t indicates when the document was last issued.BS 4514:2001 BSI 07-2001 1 1 Scope This British Standard specifies the material, appearance, dimensions and physical requirements for unplasticized poly(vinyl chloride) soil and ventilating pipes of 82.4 mm minimum mean outside diameter, fittings of size

15、 82.4 mm and other sizes of accessories, including coated metal fittings. It also specifies jointing materials for use in above-ground drainage systems of application area B (see BS EN 1329-1:2000) intended to convey domestic effluents and surface rainwater. 2 Normative references The following norm

16、ative documents contain provisions which, through reference in this text, constitute provisions of this British Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. For undated references, the latest edition of the publication referred to

17、 applies. BS 21, Specification for pipe threads for tubes and fittings where pressure-tight joints are made on the threads (metric dimensions). BS 1006:A02:1990, Methods of test for colour fastness of textiles and leather Grey scale for assessing change in colour (including half-steps). BS 1006:B01C

18、:LFS5:1998, Methods of test for colour fastness of textiles and leather Blue wool standards Reference standard for no. 5. BS 2779, Specification for pipe threads for tubes and fittings where pressure-tight joints are not made on the threads (metric dimensions). BS 2782-11:Method 1101A:1981, Methods

19、of testing plastics Thermoplastics pipes, fittings and valves Measurement of dimensions of pipes. BS 2782-11:Method 1103V:1995, Plastics piping and ducting systems Thermoplastics pipes and fittings Determination of Vicat softening temperature (VST). BS 2782-11:Method 1107A:1996, Plastics piping and

20、ducting systems Plastics pipes and fittings Method for exposure to direct (natural) weathering. BS 4346-3, Joints and fittings for use with unplasticized PVC pressure pipes Part 3: Specification for solvent cement. BS 5504-1, Wall hung WC pan Wall hung WC pan with close coupled cistern Part 1: Conne

21、cting dimensions. BS 5504-2, Wall hung WC pan Wall hung WC pan with independent water supply Part 2: Connecting dimensions. BS 5504-3, Wall hung WC pan Wall hung WC pan Part 3: Materials, quality and functional dimensions other than connecting dimensions. BS 5627, Specification for plastics connecto

22、rs for use with horizontal outlet vitreous china WC pans. BS 6209, Specification for solvent cement for non-pressure thermoplastics pipe systems. BS EN 33, Pedestal WC pans with close-coupled flushing cistern Connecting dimensions. BS EN 37, Pedestal WC pans with independent water supply Connecting

23、dimensions. BS EN 681-1:1996, Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber. BS EN 681-2, Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elasto

24、mers. BS EN 1329-1:2000, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Unplasticized poly(vinyl chloride) (PVC-U) Part 1: Specifications for pipes, fittings and the system. BS EN 1462:1997, Brackets for eaves gutters Requirements and te

25、sting.BS 4514:2001 2 BSI 07-2001 3 Materials 3.1 Pipes and fittings The material from which the pipes and fittings are produced shall consist substantially of unplasticized PVC, together with the materials necessary to enable manufacture and to ensure conformity to this standard, except for snap cap

26、s which may be produced from thermoplastics other than unplasticized PVC. The requirements for the utilization of non-virgin materials shall be as specified in Annex A of BS EN 1329-1:2000. 3.2 Weather resistance When tested using the method described in Annex A, there shall be no visible change in

27、colour between the exposed and shaded parts of the specimens. 3.3 Coated metal fittings Metal fittings, such as pipe brackets, shall meet the material and corrosion requirements of BS EN 1462:1997, clauses 4 and 5. 3.4 Elastomeric sealing rings If elastomeric sealing rings are used in joints they sh

28、all conform to BS EN 681-1:1996 Type WC or to BS EN 681-2. 3.5 Solvent cements If solvent cements are used in joints, they shall conform to BS 6209 or BS 4346-3. NOTE Cements conforming to BS 6209 are preferred. 4 Appearance 4.1 Internal and external surfaces The internal and external surfaces of pi

29、pes and fittings shall be smooth, clean and free from grooving and blistering, except for surfaces deliberately roughened for jointing to other materials. 4.2 Colour The pipes and fittings shall be coloured throughout the wall. NOTE The recommended colour of pipes and fittings is grey. 5 Dimensions

30、5.1 General Measurement of dimensions of pipes and fittings shall be carried out in accordance with the methods described in BS 2782-11:Method 1101A:1981 at (23 2) C. 5.2 Pipes Pipe diameters and wall thicknesses shall conform to the dimensions given in Table 1. The length of a pipe shall be as show

31、n in Figure 1. NOTE The preferred lengths of pipe are 2.0 m, 3.0 m and 4.0 m. Table 1 Dimensions of pipes Nominal size Mean outside diameter Extreme outside diameter a Min. wall thickness min. max. min. max. mm mm mm mm mm 82 82.4 82.8 81.0 84.3 3.0 a The extreme outside are the minimum and maximum

32、measured directionsBS 4514:2001 BSI 07-2001 3 5.3 Fittings 5.3.1 General All fittings other than connectors for WCs (see 5.3.9) and knuckle bends for soil stack connections shall conform to the requirements given in Table 2. All threaded components shall have a thread form conforming to BS 21 or BS

33、2779 and shall have a length of engagement of not less than four full threads. If a connection is to be made to a metal threaded component, the thread form shall comply with BS 21 or BS 2779, as applicable, and shall have a length of engagement of not less than four full threads. If it is necessary

34、to have a recess in the mating end of a threaded adaptor to accommodate the fitting to which it is being connected, the recess shall not extend under the threaded portion by more than 7 mm and the minimum wall thickness given in Table 3 shall not apply at the recess. NOTE Attention is drawn to BS EN

35、 1329-1 which specifies the requirements for conventional 110 and 160 fittings. Table 2 Configuration of fittings Figure 1 Pipe lengths Designated fitting angle a Bends excluding WC connectors Equal junctions (single and double) Unequal junctions (single and double) Degree 4 5 S w e p t S w e p t S

36、w e p t o r unswept 45 Swept or Unswept Swept or unswept unswept a See Figure 8. l l Solvent cement socket Ring seal socket a) Plain ended pipe b) Pipe with a socket endBS 4514:2001 4 BSI 07-2001 5.3.2 Wall thickness The wall thickness of fittings (see Figure 2) for sockets and spigots and, in addit

37、ion, for bosses and boss insertion combinations (see Figure 3) shall conform to the requirements given in Table 3. The value of e 2in a coupling, when it relates to where the wall forms the transition between sockets and spigots of different nominal diameters, shall conform to the requirements relat

38、ed to the larger diameter. The positions for measuring the wall thickness dimensions of a typical snap cap shall be as shown in Figure 4. Fittings and those parts of fittings not intended to come into contact with the fluid being transported are not required to conform to the wall thicknesses given

39、in Table 3. Figure 2 Location of dimensions and spigots e 2 e 2 L 2 e 2 e 2 ee e 3 e 3 e 3 B C A E Solvent cement socket Ring seal socketBS 4514:2001 BSI 07-2001 5 5.3.3 Lengths The lengths of designated parts of sockets and spigots (see Figure 2) shall conform to the appropriate requirements of Tab

40、le 3, except as follows: a) for joints fabricated or assembled in workshop conditions dimension L 2can be reduced to 50 % of the values given in Table 3. b) for reducers, adapters and plugs, the length E can be reduced to that given for C max.in Table 3 provided that there is a stop to prevent entry

41、 beyond the seal zone. Table 3 Dimensions of fittings including integral sockets 5.3.4 Groove designs Typical groove designs are given in Figure 7 to define positions of dimensions A, B and C, but other designs that conform to this standard shall not be excluded. Dimensions A, B and C shall conform

42、to Table 3. Some designs of sockets incorporate elastomeric ring seal zones longer than those illustrated and if they also include integral sealing membranes, the dimension C shall not apply, provided that the initial sealing action is achieved upon insertion of the pipe or spigot to a depth not gre

43、ater than the maximum value of C and that it is possible for the pipe or spigot to be further inserted to a depth at least equivalent to the maximum value of A. The dimensions of snap caps shall conform to the values given in Table 3 except for dimension B and dimension e 3related to B in Figure 2.

44、Nominal size L 2 min. mm A min. mm B min. mm C max. mm e min. mm e 2 min. mm e 3 min. mm E min. mm 36 18.0 25.0 3.8 18 3.0 2.7 2.2 18.0 43 21.0 25.0 3.8 18 3.0 2.7 2.2 21.0 56 27.0 25.0 3.8 18 3.0 2.7 2.2 27.0 82 110 160 43.0 48.0 58.0 34.0 40.0 50.0 5.0 6.0 9.0 21.0 26.0 32.0 3.0 3.2 3.2 2.7 2.9 2.

45、9 2.3 2.4 2.4 52.0 60.0 81.0 a NOTE e 2is based upon 0.9e; e 3is based upon 0.75e. Figure 3 Wall thickness of boss configurations e min. e 2 min.BS 4514:2001 6 BSI 07-2001 5.3.5 Access fittings Where fittings provide access to the discharge system, the openings shall be round or oval, and shall conf

46、orm to the dimensions given in Table 4. The design of the fitting shall make provision to maintain the fitting bore and profile. Table 4 Access dimensions Figure 4 Positions for measurement of snap cap wall thickness Figure 5 Typical reducer Nominal size Minimum clear opening size Diameter mm Oval m

47、m 36 20 n/a 43 20 n/a 56 38 n/a 82 65 75 50 110 75 100 50 160 100 100 50 e 2 e 2 e 3BS 4514:2001 BSI 07-2001 7 5.3.6 Fabricated fittings Fabricated fittings shall be manufactured from pipes and/or fittings conforming to this standard. These fabrications shall conform to 6.5. 5.3.7 Swept fittings The

48、 design dimensions of swept fittings shall conform to Table 5 and Figure 8. Table 5 Design dimensions of swept fittings Figure 6 Typical socket plug Designated fitting angle Minimum radius r a Maximum tangent angle Minimum arc length L degree mm degree mm 70 70 and 80 80 50 50 50 26 33 40 36 38 42 a

49、 The Building Regulations 2 require the 36 mm, 43 mm and 56 mm sizes to have a minimum radius of 25 mm and this table does not apply to these sizes. a) Push fit, with or without stop flange b) With screwed access plugBS 4514:2001 8 BSI 07-2001 5.3.8 Stand-off distance In fittings and clips used to fasten the pipes to a wall, the stand-off distance, i.e. the distance between the wall and the centre line of the installed pipe, shall be not less t