BS 3F 116-1995 Specification for mercerized cotton fabric《丝光棉纤维规范》.pdf

《BS 3F 116-1995 Specification for mercerized cotton fabric《丝光棉纤维规范》.pdf》由会员分享，可在线阅读，更多相关《BS 3F 116-1995 Specification for mercerized cotton fabric《丝光棉纤维规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 3F116: 1995 Specification for Mercerized cotton fabricBS3F116:1995 This British Standard, having been prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes into effect on 15 June1995 BSI10-1999 First publishe

2、d1963 Second edition February1975 Third edition June1995 The following BSI references relate to the work on this standard: Committee reference ACE/54 Draft for comment94/706286DC ISBN 0 580 24209 9 Committees responsible for this British Standard The preparation of this British Standard was entruste

3、d to Technical Committee ACE/54, Wide woven and coated fabrics for aerospace purposes, upon which the following bodies were represented: British Fabric Association British Rubber Manufacturers Association Ltd. British Textile Confederation Ministry of Defence Society of British Aerospace Companies L

4、td. Society of Dyers and Colourists Textile Finishers Association Amendments issued since publication Amd. No. Date CommentsBS3F116:1995 BSI 10-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 References 1 3 General 1 4 Yarn 1 5 Weave 1 6 Finish 1 7 Construction

5、 and properties 1 8 Permeability 2 9 Packaging 2 10 Identification 2 Table 1 General requirements (given in BS F100) 1 Table 2 Construction and properties 1 Table 3 Air permeability test requirements 2 Table 4 Air permeability retest requirements 2 List of references Inside back coverBS3F116:1995 ii

6、 BSI 10-1999 Foreword This British Standard is one of a series for textiles of a quality suitable for aerospace purposes and constitutes a revision of BS 2F116:1975, which is withdrawn. It differs from the previous edition in that the quality requirements specified in the latest edition of BS F100 h

7、ave been identified. NOTEThe latest revision of an Aerospace Series standard is indicated by a prefix number. This standard specifies pentachlorophenyl laurate (PCPL) as a rot-proofing treatment. Alternative treatments are under development, and this standard will be updated to delete PCPL as soon a

8、s a suitable alternative treatment for aerospace materials is available. WARNING. This standard calls for the use of substances and/or test procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and in no way absolves either the supp

9、lier or the user from statutory obligations relating to health and safety at any stage of manufacture or use. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British

10、 Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorp

11、orated. This will be indicated in the amendment table on the inside front cover.BS3F116:1995 BSI 10-1999 1 1 Scope This British Standard specifies requirements for a range of mercerized cotton fabrics for aerospace purposes, primarily for parachute canopies. 2 References This standard incorporates,

12、by dated or undated reference, provisions from other publications. These normative references are made at the appropriate places in the text and the cited publications are listed on the inside back cover. For dated references, only the edition cited applies; any subsequent amendments to or revisions

13、 of the cited publication apply to this standard only when incorporated in the reference by amendment or revision. For undated references, the latest edition of the cited publication applies, together with any amendments. 3 General In addition to the requirements specified in clauses4 to10 of this s

14、tandard, the requirements and tests of BS F100, as listed in Table 1, shall apply. 4 Yarn 4.1 The fabric shall be manufactured from unsized cotton yarn. 4.2 The yarn shall be two-fold and shall be mercerized. NOTEYarn plied from singles of104 dtex has been found suitable for both warp and weft. 5 We

15、ave The weave shall be plain. 6 Finish The fabric, or the yarns from which it is to be woven, shall be rendered rot-resistant by treatment with pentachlorophenyl laurate (PCPL) in accordance with BS2087-1:1992, normal process. 7 Construction and properties The finished fabric shall conform to Table

16、2. Table 1 General requirements (given in BS F100) Table 2 Construction and properties Section of BS F100 Section title Requirements and tests 1 General All requirements 2 Quality requirements Requirements for the manufacture of wide fabrics Requirements for dyed textiles Requirements for dimensions

17、 and tolerances: general and wide fabrics Requirements for freedom from corrosive impurities Requirements for freedom from faults 3 Physical tests Test for the determination of mass of wide fabrics Tests for breaking strength and extension under force of wide fabrics Test for air permeability of par

18、achute fabrics 4 Chemical tests If required by section2, further tests for freedom from corrosive impurities Designation Nominal number of threads per centimetre a Maximum mass/area Minimum average breaking strength per50mm width N Warp Weft g/m 2 Warp Weft No.583 22.1 22.1 102 480 480 No.633 25.6 2

19、5.6 127 575 575 No.813 21.3 21.3 102 480 480 a Calculated from the number in a measured length of not less than2cm.BS3F116:1995 2 BSI 10-1999 8 Permeability 8.1 When tested in accordance with clause29 of BSF100, each piece of finished fabric shall either have an average air permeability as shown in

20、Table 3, or shall conform to8.2. NOTEIt is most desirable that the average permeability of the fabric be as near as possible to the relevant mean figure shown in Table 3, and that the variation between the individual readings be low. Table 3 Air permeability test requirements 8.2 If the average perm

21、eability does not conform to Table 3 but is equal to the relevant lower value or the relevant higher value given in Table 4, then two further series of ten readings each shall be taken in different locations on the same piece. The average of each series shall be not less than the relevant lower valu

22、e, nor more than the relevant higher value, given in Table 4. All individual readings included in any of the averages shown in Table 4 shall be within the respective limits given in Table 4. 8.3 The proportion of fabric which does not conform to Table 3 shall not exceed5% of any batch tested. 8.4 Th

23、e manufacturer shall maintain quality-control sheets to provide evidence that the average level and the variability of air permeability meet the requirements of8.1 to8.3. 9 Packaging The fabric shall be made up at full width, on poles longer than the width of the fabric or on suitable tubes having a

24、 length equal to the width of the fabric. It shall be made up in continuous pieces without joins, rolled tightly and free from creases. 10 Identification The following information, supplied by the purchaser to identify the fabric for ordering purposes, shall be fully documented: a) the number of thi

25、s British Standard, i.e.BS3F116; b) the relevant designation given in Table 2. NOTEThis identification may be codified; e.g.fabric no.633 may be identified as BS 3F116633. Table 4 Air permeability retest requirements Fabric Average permeability a ft 3 /(ft 2 s) l/(m 2 s) No.583 30 3 9000 900 No.633

26、18 2 5400 600 No.813 35 4 10500 1200 a Volume of air in cubic feet passing through1ft 2of fabric in1s at10in(25.4cm) water gauge; or volume of air in litres passing through1m 2of fabric in1s at25.4cm(10in) water gauge. Fabric Average permeability a Individual readings included in average Minimum Max

27、imum ft 3 /(ft 2 s) l/(m 2 s) ft 3 /(ft 2 s) l/(m 2 s) ft 3 /(ft 2 s) l/(m 2 s) No.583 26 7800 23 6900 29 8700 34 10200 31 9300 37 11100 No.633 15 4500 13.5 4050 16.5 4950 21 6300 19 5700 23 6900 No.813 30 9000 27 8100 33 9900 40 12000 37 11100 43 12900 a Volume of air in cubic feet passing through1

28、ft 2of fabric in1s at10in(25.4cm) water gauge; or volume of air in litres passing through1m 2of fabric in1s at25.4cm(10in) water gauge.BS3F116:1995 BSI 10-1999 List of references(seeclause2) Normative references BSI publications BRITISH STANDARDS INSTITUTION, London BS 5F100:1991, Procedure for insp

29、ection and testing of textiles for aerospace purposes. BS2087, Preservative textile treatments. BS2087-1:1992, Specification for treatments. BS 3F116: 1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishSt

30、andards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the cons

31、tant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel

32、:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Se

33、rvices. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on natio

34、nal, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing

35、 members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI

36、 also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying,

37、 recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.