BS 3816-1989 Specification for epoxy resin casting systems used for electrical insulating applications at power frequencies《电源频率的电气绝缘用环氧树脂浇铸系统规范》.pdf

《BS 3816-1989 Specification for epoxy resin casting systems used for electrical insulating applications at power frequencies《电源频率的电气绝缘用环氧树脂浇铸系统规范》.pdf》由会员分享，可在线阅读，更多相关《BS 3816-1989 Specification for epoxy resin casting systems used for electrical insulating applications at power frequencies《电源频率的电气绝缘用环氧树脂浇铸系统规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 3816:1989 Specification for Epoxy resin casting systems used for electrical insulating applications at power frequencies UDC 678.686:621.315.61:621.3.016.2:621.3.018.4:001.4BS3816:1989 This British Standard, having been prepared under the directionof the Plastics StandardsCommitt

2、ee, was published under the authority ofthe Board of BSI and comes intoeffect on 28February1989 BSI 08-1999 First published November1964 First revision February1989 The following BSI references relate to the work on this standard: Committee reference PLM/39 Draft for comment86/44061 DC ISBN 0 580 17

3、068 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Plastics Standards Committee (PLM/-) to Technical Committee PLM/39, upon which the following bodies were represented: BEAMA Ltd. British Marine Industries Federation British Plastics

4、Federation British Telecommunications plc Electronic and Electrical Insulation Association (BEAMA Ltd.) Engineering Equipment and Materials Users Association ERA Technology Ltd. Ministry of Defence Process Plant Association Royal Institute of British Architects Society of British Aerospace Companies

5、 Limited The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Electronic Engineering Association Federation of Resin Formulators and Applicators Ltd. Amendments issued since publication Amd. No. Date of issue CommentsBS3816:1989 BSI 08-1999 i

6、Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Definitions 1 3 Composition 1 4 Properties 1 5 Marking 1 Appendix A Preparation of castings for testing 2 Table 1 Property requirements of castings 1 Publications referred to Inside back coverBS3816:1989 ii BSI 08-1999 F

7、oreword This British Standard has been prepared under the direction of the Plastics Standards Committee and is a revision of BS3816:1964, which is withdrawn. It covers epoxy resin casting systems used as electrical insulation in equipment for the generation, transmission and distribution of electric

8、al power. The property requirements for the material are based on a cured epoxy resin casting system incorporating an inorganic filler. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application.

9、 Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may

10、have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS3816:1989 BSI 08-1999 1 1 Scope This British Standard specifies requirements for epoxy resin casting systems used as electrical insulation in equipment for the generation, transmission and dis

11、tribution of electrical power. It does not apply to materials used in instrument transformers, gas-insulated equipment or insulators which are directly exposed to outdoor environments. NOTEThe titles of the publications referred to in this standard are listed on the inside back cover. 2 Definitions

12、For the purposes of this British Standard the following definitions apply. 2.1 batch an identifiable quantity of basic ingredient, e.g.resin, hardener, filler, designated by the supplier and being substantially uniform in quality 2.2 blend a total quantity of casting material in which the same batch

13、es of ingredients are used throughout in the same proportions with the same processing conditions 2.3 casting the cured product from the reaction between the components of the epoxy resin casting system 3 Composition The casting system shall comprise an uncured epoxy resin incorporating an inorganic

14、 filler, additives and hardeners. 4 Properties Castings prepared as described in Appendix A shall comply with the requirements given in Table 1 when tested by the methods specified therein. 5 Marking The following information shall be marked on, if practicable, or given in relation to each casting:

15、a) the name or trade mark of the manufacturer; b) the manufacturers code reference for the casting; c) the number and date of this British Standard, i.e.BS3816:1989 1) . Table 1 Property requirements of castings 1) Marking BS3816:1989 on or in relation to a product represents a manufacturers declara

16、tion of conformity, i.e.a claim by or on behalf of the manufacturer that the product meets the requirements of the standard. The accuracy of the claim is therefore solely the responsibility of the person making the claim. Such a declaration is not to be confused with third party certification of con

17、formity, which may also be desirable. Property Requirement BS2782 method Flexural strength Flexural modulus Temperature of deflection under load Electric strength at23 C Power factor, at50Hz and23 C Permittivity, at50Hz and23 C Water absorption 110MPamin. 9GPamin. 110Cmin. 10kV/mmmin. 0.02max. 5max.

18、 15mg max. 335A 335A 121A 221A 240A 240A Use specimens cut from sheet3mm thick and otherwise prepared in accordance with 5.3 of BS2782:Method430A:1983 and test in accordance with method1 in 6.2 of that standardBS3816:1989 2 BSI 08-1999 Appendix A Preparation of castings for testing A.1 Epoxy resin c

19、asting system Mix batches of the ingredients of the epoxy resin casting system in the same proportions, and as nearly as possible under the same conditions (including any vacuum treatment to remove entrapped air), to form the same blend used for the manufacture of casting. A.2 Test castings Cast all

20、 test castings under as nearly as possible the same conditions used for production castings. Produce the castings in closed moulds so designed that the casting system is poured into the gap which will constitute either one edge, or part of an edge, of sheet samples or one end of rod samples. If need

21、ed, apply a mould release agent recommended by the resin supplier to all surfaces of the mould coming into contact with the casting system. To reduce the risk of air entrapment in the casting incline the mould at an angle of about30 from the vertical whilst slowly pouring the casting resin onto the

22、inner surface of the lower face of the mould cavity. Cure the test castings under as nearly as possible the same conditions as the production castings.BS3816:1989 BSI 08-1999 Publications referred to BS2782, Methods of testing plastics. BS2782-1, Thermal properties. BS2782:Method121A, Determination

23、of temperature of deflection under a bending stress of1.8MPa, of plastics and ebonite. BS2782-2, Electrical properties. BS2782:Method221A, Determination of electric strength: step-by-step method 2) . BS2782:Method240A and240B, Determination of loss tangent and permittivity at power and audio frequen

24、cies. BS2782-3, Mechanical properties. BS2782:Method335A, Determination of flexural properties of rigid plastics. BS2782-4, Chemical properties. BS2782:Method430A, Determination of water absorption at23 C 3) . 2) Included in BS2782:Methods220 and221 3) Included in BS2782:Methods430A to430DBS 3816:19

25、89 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards a

26、re updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this B

27、ritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the lat

28、est editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those t

29、hat have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services ar

30、e also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of thes

31、e and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs a

32、nd Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of ne

33、cessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.