BS 3762-3 18-1985 Analysis of formulated detergents - Quantitative test methods - Method for determination of chlorine oxidizing agents content《配制洗涤剂分析 第3部分 定量试验方法 第18节 氯氧化剂含量的测定方法.pdf

《BS 3762-3 18-1985 Analysis of formulated detergents - Quantitative test methods - Method for determination of chlorine oxidizing agents content《配制洗涤剂分析 第3部分 定量试验方法 第18节 氯氧化剂含量的测定方法.pdf》由会员分享，可在线阅读，更多相关《BS 3762-3 18-1985 Analysis of formulated detergents - Quantitative test methods - Method for determination of chlorine oxidizing agents content《配制洗涤剂分析 第3部分 定量试验方法 第18节 氯氧化剂含量的测定方法.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS3762-3.18: 1986 Analysis of formulated detergents Part3: Quantitative test methods Section3.18 Method for determination of chlorine oxidizing agents content NOTEIt is recommended that this Section be read in conjunction with the information in the “General Introduction”, published

2、 separately as BS3762-0. UDC 661.185:543BS3762-3.18:1986 This BritishStandard, having been prepared under the directionof the Chemicals Standards Committee, was published under the authorityofthe Board of BSI andcomes into effect on 31December1985 BSI12-1999 The committees responsible forthis Britis

3、hStandard are showninPart0. The following BSI references relate to the work on this standard: Committee reference CIC/34 Draft for comment84/53114 DC ISBN 0 580 14923 4 Foreword This Section of BS3762 has been prepared under the direction of the Chemicals Standards Committee and supersedes sectionII

4、 of method D9 of BS3762:1964. This standard describes a method of test only and should not be referred to as a specification defining limits of purity. Reference to the standard should indicate that the method of test used is in conformity with BS3762-3.18. A British Standard does not purport to inc

5、lude all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, page

6、si andii, pages1 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue CommentsBS37

7、62-3.18:1986 BSI 12-1999 i Contents Page Foreword Inside front cover 1 Scope 1 2 Principle 1 3 Reagents 1 4 Apparatus 1 5 Procedure 1 6 Calculation 1 7 Test report 2 Publications referred to Inside back coverii blankBS3762-3.18:1986 BSI 12-1999 1 1 Scope This Section of BS3762 describes a method for

8、 the determination of chlorine oxidizing agents in detergent formulations. The presence of other oxidizing agents may interfere. NOTEThe titles of the publications referred to in this Section are listed on the inside back cover. 2 Principle Potassium iodide is added to the sample. Any chlorine oxidi

9、zing agents react with this to yield iodine. The liberated iodine is determined by visual or potentiometric titration with standard volumetric sodium thiosulphate solution. Results are expressed as available chlorine. 3 Reagents The reagents shall be of a recognized analytical grade. Water complying

10、 with BS3978 shall be used throughout. 3.1 Potassium iodide 3.2 Sulphuric acid solution, c(H 2SO 4 )=5mol/L approximately. 3.3 Sodium thiosulphate solution, c(Na 2 S 2 O 3 )=0.100mol/L. 3.4 Starch indicator,10g/L solution, freshly prepared. 4 Apparatus Ordinary laboratory apparatus, the apparatus de

11、scribed in4.1 and, if potentiometric titration is used, the apparatus detailed in4.2 to4.4 are required. 4.1 One-mark volumetric flask, of250mL capacity, complying with class B of BS1792. 4.2 pH meter (complying with BS3145) or other apparatus suitable for potentiometric titration 4.3 Platinum elect

12、rode 4.4 Calomel reference electrode 5 Procedure 5.1 Test portion Weigh, to the nearest0.05g, approximately10g of sample into a250mL beaker. Add150mL of water and stir to dissolve. Transfer to the250mL one-mark volumetric flask(4.1) and dilute to the mark with water. Transfer an aliquot portion of t

13、his solution to a250mL conical flask as follows. Adjust the total volume in the flask to approximately100mL by addition of water. Weigh approximately2g of the potassium iodide(3.1) and add to the flask. Add10mL of the sulphuric acid solution(3.2). Titrate with the sodium thiosulphate solution(3.3) e

14、ither visually or potentiometrically as described in5.2 or5.3, respectively. 5.2 Visual titration Titrate with the sodium thiosulphate solution until the iodine colour is almost gone. Add1mL of the starch indicator solution(3.4) and complete the titration to the disappearance of the blue colour. Rec

15、ord the titration volume, T. 5.3 Potentiometric titration Introduce the platinum and reference electrodes(4.3 and4.4) connected to the pH meter(4.2) and, while stirring, titrate with the sodium thiosulphate solution. Plot a graph of millivolts or pH scale readings against millilitres of the sodium t

16、hiosulphate solution. Read off the volume, T, in millilitres corresponding to the steepest part of the graph. 6 Calculation The oxidizing agents content, expressed as a percentage by mass of available chlorine, is given by the following expression. Available chlorine content Aliquot volume % (m/m) (

17、mL) 0 to2 100 2 to5 50 5 to10 25 where T is the volume of the sodium thiosulphate solution (inmL); m is the mass of the test portion (ing); A is the volume of the aliquot portion taken in5.1 (inmL).BS3762-3.18:1986 2 BSI 12-1999 7 Test report The test report shall include the following information:

18、a) a reference to this BritishStandard, i.e.BS3762-3.18; b) the results and the method of expression used.BS3762-3.18:1986 BSI 12-1999 Publications referred to BS1792, Specification for one-mark volumetric flasks. BS3145, Specification for laboratory pH meters. BS3978, Water for laboratory use. BS37

19、62-3.18: 1986 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British

20、Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while u

21、sing this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rece

22、ive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation

23、 of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information

24、services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For deta

25、ils of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright

26、, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the stan

27、dard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.