BS 2853-2011 Specification for the testing of steel overhead runway beams for hoist blocks《起重机块用钢制高空跑道梁的试验用规范》.pdf

《BS 2853-2011 Specification for the testing of steel overhead runway beams for hoist blocks《起重机块用钢制高空跑道梁的试验用规范》.pdf》由会员分享，可在线阅读，更多相关《BS 2853-2011 Specification for the testing of steel overhead runway beams for hoist blocks《起重机块用钢制高空跑道梁的试验用规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS 2853:2011Specification for the testingof steel overhead runwaybeams for hoist blocksPublishing and copyright informationThe BSI copyright notice displayed in this document ind

2、icates when the documentwas last issued. BSI 2011ISBN 978 0 580 71930 1ICS 77.140.70The following BSI references relate to the work on this standard:Committee reference CB/203Draft for comment 10/30229805 DCPublication historyFirst published May 1957Second edition, October 2011Amendments issued sinc

3、e publicationDate Text affectedBS 2853:2011 BRITISH STANDARDContentsForeword ii1 Scope 12 Normative references 13 Terms and definitions 14 Information to be supplied 15 Design 16 Deflection 27 End stops 28 Testing and inspection 29 Marking 310 Certificates 4Bibliography 5Summary of pagesThis documen

4、t comprises a front cover, an inside front cover, pages i to ii,pages 1 to 6, an inside back cover and a back cover.BRITISH STANDARD BS 2853:2011 BSI 2011 iForewordPublishing informationThis British Standard is published by BSI and came into effect on 31 October2011. It was prepared by Technical Com

5、mittee CB/203, Design and execution ofsteel structures. A list of organizations represented on this committee can beobtained on request to its secretary.SupersessionThis British Standard, together with BS EN 1993-6 (and its associated NationalAnnex), supersedes BS 2853:1957, which is withdrawn.Infor

6、mation about this documentThis is a full revision of the standard, and introduces the following principalchanges. The detailed requirements for structural design have been removed. Requirements about the slopes of beams have been added. It has been clarified that the deflection limits for beams are

7、relative to theirsupports. The former references to Statutory Requirements have been removed. The detailed requirements for Test Certificates have been removed. References to The Lifting Operations and Lifting Equipment Regulations1998 1 have been added.Previous editions of this British Standard als

8、o covered the structural design ofthe runway beams. This is now covered by BS EN 1993-6, in association withBS EN 1991-3, and their associated National Annexes.Presentational conventionsThe provisions of this standard are presented in roman (i.e. upright) type. Itsrequirements are expressed in sente

9、nces in which the principal auxiliary verb is“shall”.Commentary, explanation and general informative material is presented insmaller italic type, and does not constitute a normative element.Contractual and legal considerationsThis publication does not purport to include all the necessary provisions

10、of acontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legalobligations.BRITISH STANDARDBS 2853:2011ii BSI 20111 ScopeThis British Standard specifies requirements for the testing of fixed overheadrunway beams made from rolled st

11、eel sections.This British Standard applies to the runway beams and their components only. Itdoes not apply to supporting structures, travelling trolleys or lifting appliancesoperating on the beams, nor to runway beams for cranes that run on rails.2 Normative referencesThe following referenced docume

12、nts are indispensable for the application ofthis document. For dated references, only the edition cited applies. For undatedreferences, the latest edition of the referenced document (including anyamendments) applies.BS EN ISO 7500-1, Metallic materials Verification of static uniaxial testingmachines

13、 Part 1: Tension/compression testing machines Verification andcalibration of the force-measuring system3 Terms and definitionsFor the purposes of this British Standard the following terms and definitionsapply.3.1 certifierperson signing the certificates specified in this British Standard3.2 runwayru

14、nway beam and runway components3.3 runway beamoverhead track for carrying loads which are moved along it3.4 runway componentsthose parts of the runway immediately attached to the runway beam,e.g. splices, end stops, clamps and switches4 Information to be suppliedThe certifier shall be supplied with

15、full details of the loads to be handled andthe service required of the runway. This information shall form the basis of thetest. These loads shall include any additional items, such as apparatus or services,which might have to be supported by the runway.5 DesignThe runway beam on which the trolley m

16、oves shall be of sufficient size andstrength, and have an even running surface. It shall be appropriately supportedor suspended, and readily accessible for maintenance.The design and layout of the runway beam and its supporting structure shall besuch as to ensure that before the application of loads

17、 to the runway beam, itsslope does not deviate by more than 1 in 250 from the horizontal, or from itsintended slope.NOTE For the structural design of runway beams, see BS EN 1991-3 andBS EN 1993-6.BRITISH STANDARD BS 2853:2011 BSI 2011 16 DeflectionThe maximum measured deflection of a runway beam un

18、der the safe workingload, relative to its supports, shall not exceed 1/500 of the span.For a cantilever beam, the maximum measured deflection under the safeworking load, relative to its supports, shall not exceed 1/250 of the span.7 End stopsEnd stops shall be provided on the runway to prevent the t

19、rolley either fallingfrom the beams or hitting the structure of the building in which the runway isinstalled. The stops shall not operate on the flanges of the trolley wheels.The end stops shall be designed to be effective for all types of trolley.8 Testing and inspection8.1 Duty of certifierThe per

20、son signing the certificate specified in 10.1 shall satisfy themselves thatthe deflections specified in Clause 6 are not exceeded and that all otherrequirements of this British Standard are conformed to.NOTE The prime duty of the certifier is to test the actual runway; nevertheless theyshould satisf

21、y themselves that the supports and structures are sound and suitable forall loads which they are called upon to take.8.2 Accuracy of the loadsThe loads shall be measured by a load cell calibrated to BS EN ISO 7500-1, suchthat the sum of the inaccuracies of the load and the load cell do not exceed2%.

22、NOTE The load referred to includes the test frame, chain slings, tackle, etc. and theload cell if used on the actual test.8.3 Amount of the proof loadThe proof load applied shall be the weight of the appropriate heaviest liftingappliance supported by the runway plus 125% of the safe working load of

23、thisappliance.Where the runway supports more than one transporting or lifting appliance,due allowance shall be made for the permissible proximity of any otherappliance or appliances supported by the runway.8.4 Inspection before application of loadsAll joints, connections and supports shall be carefu

24、lly inspected, and specialattention shall be paid to the security of nuts on bolts. Attention shall be paidto the condition of walls surrounding and adjacent to the end fastening ofrunways fixed therein.Where the runway beam is carried on timber supports (which in many casesmight be roof trusses), i

25、t shall be the responsibility of the owner to satisfy thetester that the members are suitable for the load to be carried.NOTE It is recommended that, where reinforced concrete beams are used for thesuspension of runways, the beams should be coated with whitewash or similar, toreveal any cracks that

26、develop under the proof load.BRITISH STANDARDBS 2853:20112 BSI 20118.5 Application of loadsOnce the preliminary inspection has been carried out as specified in 8.4, a testload equivalent to the maximum safe working load, together with the weight ofthe heaviest transporting or lifting appliance suppo

27、rted by the runway, shall beapplied and traversed along the whole length of the runway. The load shall behalted at appropriate positions during its passage along the runway and kept atrest while stable deflection readings are recorded at these positions and at thecorresponding support points so that

28、 net values can be determined.For straight, simply supported runways, the net deflection shall be determinedat mid-span and at cantilever ends. In other cases, sufficient readings shall betaken to ensure that the maximum net deflection has been obtained.The procedure outlined above shall then be rep

29、eated except that: instead of the test load referred to in the first paragraph, the proof load(see 8.3) shall be applied; the stable net deflection shall be recorded only at that position where themaximum reading was obtained during the application of the test loadreferred to in the first paragraph.

30、8.6 Deflection measuring equipmentDeflection measuring equipment shall be capable of measuring the verticaldeflection of the beam at any point within 5% of the maximum permitteddeflection of the beam.8.7 Inspection and thorough examinationDuring the application of the test load referred to in 8.5 an

31、d of the proof loadas specified in 8.5 the runway shall be kept under such visual observation as toensure the ready detection of any obvious defect in the runway.Following the application of the proof load as specified in 8.5 the runway shallbe thoroughly examined in order to ascertain, for the purp

32、oses of Clause 10,that the runway has withstood the proof load without damage or permanentdeformation.NOTE 1 For the purpose of this subclause, thorough examination means a carefulvisual examination, supplemented, where relevant, by other tests includingnon-destructive testing of critical welds and

33、checking the tightness of pre-loadedbolts, in order to arrive at a reliable conclusion as to the safety of the runway.If dismantling is necessary for the purpose of examination, the load test andbolt tightening check shall be repeated afer reassembly.NOTE 2 Further statutory requirements are given i

34、n The Lifting Operations andLifting Equipment Regulations 1998 1.9 MarkingThe safe working load, identification number and any limiting conditions shallbe plainly and permanently marked on the runway so as to be clearly visible tothe operator. The marking shall include either the maximum hoisting sp

35、eed for apower hoist or else the words “Manual Hoist”.NOTE The safe working load referred to here applies to the runway beam and itscomponents only; it does not apply to a travelling trolley or lifting applianceoperating on the runway beam. Hence, the actual load lifted, lowered, ortransported in an

36、y particular instance, is not only governed by the safe working loadof the runway beam, but also the safe working load of the trolley and liftingappliance used, and any other relevant factors, e.g. any limitation governing theoperation of an adjacent trolley and lifting appliance.BRITISH STANDARD BS

37、 2853:2011 BSI 2011 310 Certificates10.1 Certificate of test and thorough examinationBefore any runway beam is taken into use the first time after erection,re-erection or having undergone any substantial alteration or repair, a certificatethat the runway beam has been tested and subsequently thoroug

38、hly examinedas required by 8.7 shall be supplied.The certificate shall identify the runway beam to which it refers, quoting itsdistinguishing number or mark and grades of steel, its size and length, andstate:a) the date on which the proof load was applied and thorough examinationmade;b) the position

39、 and magnitude of the deflections obtained during thetraversing of the maximum safe working load and of the proof load asrequired by 8.5;c) the maximum safe working load; andd) that the runway beam conforms in all respects to this British Standard,i.e. BS 2853:2011.1)The certificate, which shall be

40、signed by the person making the test andexamination, shall indicate clearly that it applies to the runway beam only andnot to any trolley or lifting appliance travelling thereon.NOTE Further statutory requirements are given in The Lifting Operations andLifting Equipment Regulations 1998 1.10.2 Certi

41、ficate of thorough examinationWhen a thorough examination only is made of a runway beam already in useand for which a certificate of test and thorough examination as referred toin 10.1 has been granted, the certificate of such examination shall identify therunway beam to which it refers, quoting its

42、 distinguishing number or mark andgrades of steel, its size and length, and state:a) the date on which the examination was made;b) the date of the certificate of test and thorough examination referred toin 10.1; andc) particulars of any defect found during the examination and affecting themaximum sa

43、fe working load and of the steps taken to remedy such defect.The certificate, which shall be signed by the person making the examination,shall indicate clearly that it applies to the runway beam only and not to anytrolley or lifting appliance travelling thereon.NOTE Further statutory requirements ar

44、e given in The Lifting Operations andLifting Equipment Regulations 1998 1.1)Marking BS 2853:2011 on or in relation to a product represents a manufacturersdeclaration of conformity, i.e. a claim by or on behalf of the manufacturer that theproduct meets the requirements of the standard. The accuracy o

45、f the claim is solelythe claimants responsibility. Such a declaration is not to be confused with third-partycertification of conformity.BRITISH STANDARDBS 2853:20114 BSI 2011BibliographyStandards publicationsFor dated references, only the edition cited applies. For undated references, thelatest edit

46、ion of the referenced document (including any amendments) applies.BS EN 1991-3, Eurocode 1 Actions on structures Part 3: Actions induced bycranes and machinery.BS EN 1993-6, Eurocode 3 Design of steel structures Part 6: Crane supportingstructuresOther publications1 GREAT BRITAIN. The Lifting Operati

47、ons and Lifting Equipment Regulations1998. London: HMSO.BRITISH STANDARD BS 2853:2011 BSI 2011 5BRITISH STANDARDBS 2853:20116 BSI 2011 This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards

48、-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20

49、 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.