BS 1902-3 2-1981 Methods of testing refractory materials - General and textural properties - Measurement of dimensions of specimens for testing (methods 1902-302)《耐火材料试验方法 第3部分 一般特.pdf

《BS 1902-3 2-1981 Methods of testing refractory materials - General and textural properties - Measurement of dimensions of specimens for testing (methods 1902-302)《耐火材料试验方法 第3部分 一般特.pdf》由会员分享，可在线阅读，更多相关《BS 1902-3 2-1981 Methods of testing refractory materials - General and textural properties - Measurement of dimensions of specimens for testing (methods 1902-302)《耐火材料试验方法 第3部分 一般特.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 1902-3.2: 1981 Methods of testing Refractory materials Part 3: General and textural properties Section 3.2 Measurement of dimensions of specimens for testing (methods 1902-302) UDC 666.76.017:620.115.8BS1902-3.2:1981 This British Standard, having been prepared under the direction

2、of the Refractory Products Standards Committee, was published under the authorityof the Executive Boardand comes into effect on 27February 1981 BSI 07-1999 The following BSI references relate to the work on this standard: Committee reference RPE/1 Draft for comment 79/74383 DC ISBN 0 580 11711 1 Coo

3、perating organizations The Refractory Products Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the following: British Ceramic Research Association* British Steel Industry* Cbmpe Cement Makers Federation Chemical Industries Association C

4、oke Oven Managers Association Combustion Engineering Association Engineering Equipment Users Association* Glass Manufacturers Federation Institute of Refractories Engineers Refractories Association of Great Britain* Society of British Gas Industries Society of Chemical Industry Society of Glass Tech

5、nology* Society of Industrial Furnace Engineers The organizations marked with an asterisk in the above list, together with the following, were directly represented on the Technical Committee entrusted with the preparation of this British Standard: British Cast Iron Research Association Electricity S

6、upply Industry in England and Wales Institute of Petroleum Amendments issued since publication Amd. No. Date of issue CommentsBS1902-3.2:1981 BSI 07-1999 i Contents Page Cooperating organizations Inside front cover Foreword ii 1 Scope 1 2 Reference 1 3 Designation 1 4 Apparatus 1 5 Procedure 1 6 Exp

7、ression of results 1 7 Test report 1 Publication referred to Inside back coverBS1902-3.2:1981 ii BSI 07-1999 Foreword This Section of this British Standard has been prepared under the direction of the Refractory Products Standards Committee. A British Standard does not purport to include all the nec

8、essary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1

9、 and2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS1902-3.2:1981 BSI 07-1999 1 NOTEThis Section is to be read in conjunction with BS1902-

10、3.0 “Introduction” and BS1902-3.1 “Guidance on sampling”. Section 3.0 shows the general arrangement of BS1902 and lists the Sections of Part 3. 1 Scope This Section specifies the methods for measuring the dimensions of bricks and test pieces that are nominally rectangular or cylindrical in shape. 2

11、Reference The title of the standards publication referred to in this Section of this British Standard is given on the inside back cover. 3 Designation The methods specified in this Section may be referred to by the following designations. 4 Apparatus The following apparatus is required. 4.1 Vernier

12、caliper, (see BS887) for measuring rectangular or cylindrical specimens. 4.2 Flat steel rule, which may be used in place of the vernier caliper if only rectangular specimens are to be measured. The rule may have a fixed hook at one end, consisting of a piece of hard steel projecting not more than 6m

13、m at right angles to the edge of the rule, to fix the zero point of the scale against one edge of the brick. The rule may also have a sliding hook of similar dimensions. 5 Procedure 5.1 The definition of the edges and surfaces may be improved by the removal of any fringes, small blisters, etc.by lig

14、ht abrasion. 5.2 If a steel rule is used, the edges of the brick or test piece bounding the dimensions being measured shall be in contact with the rule while the scale is read. 5.3 If a steel rule is used without a hook, the zero point of the rule shall be set against a plane surface held in contact

15、 with the face of the specimen at right angles to the one being measured. 5.4 In the case of a rectangular brick or specimen, measure the three principal dimensions (length, width and thickness) of each brick or test piece to the appropriate accuracy 1) , using a vernier caliper or a flat steel rule

16、 (seeclause 4). The measurements shall be made at the centre line of each face (i.e.four times for each dimension). 5.5 In the case of a cylindrical specimen, measure six diameters to the accuracy required 1) , using a vernier caliper, two at right angles to each other near one end of the specimen,

17、two near the middle, and two near the other end. Measure the length of the cylinder at the extremeties of two diameters at right angles to each other (i.e.four times). 6 Expression of results 6.1 Dimensions shall be expressed in millimetres and decimal fractions of a millimetre. 6.2 Unless otherwise

18、 required by the description of the method of test for which the measurements are being made, report the individual measurements and the mean measurement for each dimension of each test specimen. 7 Test report 7.1 If, as will often be the case, the measurements are made for the purposes of a test de

19、scribed in another Section of this standard, no separate test report of the measurements is required. The fact that the measurements were made in accordance with this method of test (e.g. 1902-302/1) shall, however, be included in the report of the other tests. 7.2 If, exceptionally, a separate test

20、 report of the measurements is required, it shall include the following: a) the name of the establishment where the measurements were made; b) the date the measurements were made; c) a reference to this method of test, e.g.measured by method 1902-302/1 (seeclause3); d) the description of the item me

21、asured (manufacturer, type, batch number, etc.); e) the individual values and the mean value for each dimension of each item measured; f) in the case of a rectangular specimen, whether the measurements were made using a vernier caliper or a steel rule. Measurement using a vernier caliper Method 1902

22、-302/1 Measurement using a steel rule Method 1902-302/2 1) The accuracy required depends upon the purpose of the test and should be indicated in the description of the method of test.2 blankBS1902-3.2:1981 BSI 07-1999 Publication referred to BS 887, Vernier calipers. BS 1902-3.2: 1981 BSI 389 Chiswi

23、ck High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by ame

24、ndment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard wo

25、uld inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of s

26、tandards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been pub

27、lished as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available

28、which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benef

29、its contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 198

30、8 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details su

31、ch as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.