BS 1363-5-2016 13 A plugs socket-outlets adaptors and connection units Part 5 Specification for fused conversion plugs《13A插头、电源插座、适配器和连接装置 第5部分 装有保险丝的转换插头用规范》.pdf

《BS 1363-5-2016 13 A plugs socket-outlets adaptors and connection units Part 5 Specification for fused conversion plugs《13A插头、电源插座、适配器和连接装置 第5部分 装有保险丝的转换插头用规范》.pdf》由会员分享，可在线阅读，更多相关《BS 1363-5-2016 13 A plugs socket-outlets adaptors and connection units Part 5 Specification for fused conversion plugs《13A插头、电源插座、适配器和连接装置 第5部分 装有保险丝的转换插头用规范》.pdf（80页珍藏版）》请在麦多课文档分享上搜索。

1、BS 1363-5:201613 A plugs, socket-outlets,adaptors and connectionunitsPart 5: Specification for fusedconversion plugsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Publishing and copyright informationThe BSI copyright notice displayed in this document indicates when

2、the documentwas last issued. The British Standards Institution 2016Published by BSI Standards Limited 2016ISBN 978 0 580 85813 0ICS 29.120.30The following BSI references relate to the work on this document:Committee reference PEL/23Draft for comment 15/30297240 DCPublication historyFirst published A

3、ugust 2008Second (present) edition, August 2016Amendments issued since publicationDate Text affectedBS 1363-5:2016 BRITISH STANDARDContentsForeword iii1 Scope 12 Normative references 13 Terms and definitions 24 Classification 55 General requirements 56 Testing regime 67 Marking and labelling 88 Clea

4、rances, creepage distances, and solid insulation 109 Accessibility of live parts 1410 Provision for earthing 1511 Contacts in conversion plugs 1612 Construction of conversion plugs 1613 (Not used) 2614 Resistance to ageing and to humidity 2615 Insulation resistance and electric strength 2716 Tempera

5、ture rise 2817 (Not used) 3018 (Not used) 3019 Connection of the non-BS 1363 type plug and non-BS 1363 type plugretention in conversion plugs 3020 Mechanical strength 3321 Screws, current-carrying parts and connections 3422 Resistance to heat 3623 Resistance to abnormal heat and fire 3724 Resistance

6、 to excessive residual stresses and to rusting 38AnnexesAnnex A (normative) The construction and calibration of a calibrated link 63Annex B (normative) Measurement of clearances and creepage distances 64Annex C (normative) Determination of the comparative tracking index (CTI) andproof tracking index

7、 (PTI) 68Annex D (normative) Relationship between rated impulse withstand voltage,rated voltage and Overvoltage Category 68Annex E (normative) Pollution degree 69Annex F (normative) Impulse voltage test 69Bibliography 71List of figuresFigure1Testpin(see Clause 12) 39Figure 2a Apparatus for mechanica

8、l strength test on resilient covers (see Clause9) 40Figure 2b Hardwood block for Figure 2a 41Figure 4a Dimensions and disposition of pins (see Clause 12) 42Figure 4b Concave shrinkage allowance for ISODs 44Figure 5 Gauge for plug pins (see Clause 12, Clause 20 and Clause 22) 45Figure 6 Apparatus for

9、 testing plug cover fixing screws (see Clause 12) 46Figure 7 Mounting plate (see Clause 12) 47Figure 8 Plug pin deflection test apparatus for resilient plugs(see Clause 12) 48Figure 9 Apparatus for abrasion test on insulating sleeves of plug pins (seeClause 12) 50Figure 10 Apparatus for pressure tes

10、t at high temperature (see Clause 12) 51Figure 11 GO gauge for socket-outlet (see Clause 13) 52Figure 17a Test apparatus for temperature rise test (see Clause 16) 53Figure 17b Dummy front plate for temperature rise (see Clause 16) 54Figure 18 Apparatus for flexing test (see Clause 19) 55BRITISH STAN

11、DARD BS 1363-5:2016 The British Standards Institution 2016 iFigure 19 Solid link for test on fuse clips (see Clause 20) 56Figure 20 Tumbling barrel (see Clause 20) 56Figure 23 Apparatus for pressure test (see Clause 22) 57Figure 24 Apparatus for ball pressure test (see Clause 22) 58Figure 28 Calibra

12、ted link (see A.1) 59Figure 29 Calibration jig for calibrated link (see A.2) 60Figure 32a Apparatus for tests on conversion plug pins: A plug pin under test(see Clause 12) 61Figure 32b Apparatus for tests on conversion plug pins: Details of anvils(see Clause 12) 62Figure 33 Apparatus for torsion tes

13、t on pins (see Clause 12) 62Example 1 65Example 2 65Example 3 65Example 4 65Example 5 66Example 6 66Example 7 66Example 8 66Example 9 67Example 10 67Example 11 68List of tablesTable 1 Schedule of tests 7Table 2 Rated current and maximum fuse rating in normal use, and load forflexing and cable grip t

14、ests related to size of flexible cable 9Table 3 Minimum clearances for basic insulation 11Table 4 Minimum creepage distances (mm) for basic insulation 12Table 5 Withstand voltages for insulation types 14Table 6 Permitted temperature rises 29Table7Torque values for screws and nuts 31Table 8 Plug disp

15、lacement test loads 32Table 9 Application of glow-wire test 38Table B.1 Minimum values of width X64Table D.1 Rated impulse withstand voltage for conversion plugs energizeddirectly from the low voltage mains 68Table F.1 Test voltages for verifying clearances at sea level 70Summary of pagesThis docume

16、nt comprises a front cover, an inside front cover, pages i to iv, pages1 to 72, an inside back cover and a back cover.BRITISH STANDARDBS 1363-5:2016ii The British Standards Institution 2016ForewordPublishing informationThis part of BS 1363 is published by BSI Standards Limited, under licence fromThe

17、 British Standards Institution, and came into effect on 31 August 2016. It wasprepared by Technical Committee PEL/23, Electrical accessories. A list oforganizations represented on this committee can be obtained on request to itssecretary.SupersessionThis part of BS 1363 supersedes BS 1363-5:2008, wh

18、ich remains current and willbe withdrawn on 31 August 2019.Information about this documentBS 1363 comprises five parts covering the following: Part 1: Specification for rewirable and non-rewirable 13 A fused plugs; Part 2: Specification for 13 A switched and unswitched socket-outlets; Part 3: Specif

19、ication for adaptors; Part 4: Specification for 13 A fused connection units switched andunswitched; Part 5: Specification for fused conversion plugs.NOTE In order to prevent confusion with BS 1363:1984, the figure andclause numbers have been retained.This new edition of BS 1363-5 incorporates techni

20、cal changes only. It does notrepresent a full review or revision of the standard, which will be undertaken indue course.Presentational conventionsThe provisions of this standard are presented in roman (i.e. upright) type. Itsrequirements are expressed in sentences in which the principal auxiliary ve

21、rb is“shall”.Commentary, explanation and general informative material is presented insmaller italic type, and does not constitute a normative element.Requirements in this standard are drafted in accordance with Rules for thestructure and drafting of UK standards, subclause J.1.1, which states,Requir

22、ements should be expressed using wording such as: When tested asdescribed in Annex A, the product shall . This means that only those productsthat are capable of passing the specified test will be deemed to conform to thisstandard.Contractual and legal considerationsThis publication does not purport

23、to include all the necessary provisions of acontract. Users are responsible for its correct application.Conformity with a British Standard cannot confer immunity from legalobligations.Particular attention is drawn to the following specific regulations:The Plugs and Sockets etc. (Safety) Regulations

24、1994. SI No. 1768.BRITISH STANDARD BS 1363-5:2016 The British Standards Institution 2016 iiiBRITISH STANDARDBS 1363-5:2016This page deliberately left blankiv The British Standards Institution 20161 ScopeThis part of BS 1363 specifies requirements, with particular reference to safety innormal use, fo

25、r 13 A, fused, conversion plugs for household, commercial andlight industrial purposes.The scope of the standard covers two-pole plus earth conversion plugs that areeither reusable or non-reusable and that are suitable for the connection ofnon-BS 1363 type plugs, conforming to a recognized standard,

26、 to socket-outletsconforming to BS 1363-2:2016.The scope of this standard is limited to devices with the following characteristics: that have insulating sleeves on line and neutral pins; that have one plug portion and one set of contacts intended to connect toa non-BS 1363 type plug that conforms to

27、 the dimensional requirements ofa standard listed in IEC TR 60083 and not exceeding 13 A; that are suitable for the connection of electrical equipment in a.c. circuitsonly, operating at voltages not exceeding 250 V r.m.s. at 50 Hz; that may have the un-terminated metal earth pin replaced with a simi

28、larlydimensioned insulated shutter opening device (ISOD) designed to operatethe shutter mechanism of a socket-outlet conforming to BS 1363-2:2016.Two categories of conversion plugs are specified, covering normal and roughuse.Conversion plugs specified in this standard are intended for the connection

29、 ofloads to socket-outlets; they are not intended for the connection of electricalpower generators to socket-outlets.Conversion plugs incorporating switches, transformers, thermostats, or othercontrol means are outside the scope of this part of BS 1363.This standard also does not cover: non-BS 1363

30、type conversion plugs, i.e. with a contact set to fit 13 A plugs,and a male plug portion suitable for a non-BS 1363 type socket-outlet; adaptors (see BS 1363-3:2016); or travel adaptors (see BS 8546:2016).2 Normative referencesThe following referenced documents are indispensable for the application

31、ofthis document. For dated references, only the edition cited applies. For undatedreferences, the latest edition of the referenced document (including anyamendments) applies.Standards publicationsBS 219:1977, Specification for soft soldersBS 1362:1973, Specification for general purpose fuse links fo

32、r domestic andsimilar purposes (primarily for use in plugs)BS 1363-2:2016, 13 A plugs, socket-outlets, adaptors and connection units Part 2: Specification for 13 A switched and unswitched socket-outletsBS 2572:1990, Specification for phenolic laminated sheet and epoxy cotton fabriclaminated sheetBS

33、2870:1980, Rolled copper and copper alloys sheet, strip and foilBRITISH STANDARD BS 1363-5:2016 The British Standards Institution 2016 1BS 4662:2006+A1:2009, Boxes for flush mounting of electrical accessories Requirements and test methods and dimensionsBS 4800:2011, Schedule of paint colours for bui

34、lding purposesBS EN 10270-1:2011, Steel wire for mechanical springs Part 1: Patented colddrawn unalloyed spring steel wireBS EN 60112:2003+A1:2009, Method for the determination of the proof and thecomparative tracking indices of solid insulating materialsBS EN 60664-1:2007, Insulation coordination f

35、or equipment within low-voltagesystems Part 1: Principles, requirements and testsBS EN 60695-2-11:2014, Fire hazard testing Part 2: Glowing/hot wire based testmethods Glow-wire flammability test method for end-products (GWEPT)BS EN 60695-10-2:2014, Fire hazard testing Part 10: Abnormal heat Ballpres

36、sure test methodBS EN 61032:1998, Protection of persons and equipment by enclosures Probesfor verificationBS EN 61180-1:1995, Guide to high-voltage test techniques for low-voltageequipment Part 1: Definitions, test and procedure requirementsIEC 60038, IEC standard voltagesIEC TR 60083, Plugs and soc

37、ket-outlets for domestic and similar general usestandardized in member countries of IEC3 Terms and definitionsFor the purposes of this part of BS 1363, the following terms and definitionsapply.NOTE Where the terms voltage and current are used, they imply r.m.s. values,unless otherwise stated.3.1 con

38、version plugfused device that can be engaged with a socket-outlet conforming toBS 1363-2:2016, and that is designed to enclose the non-BS 1363 type plug andenables it to be engaged with such a socket-outlet3.2 normal useconditions during use which: do not exceed the conditions intended by the manufa

39、cturer; are not excessive, rough use or gross misuse; do not exceed reasonably foreseeable conditions of misuse3.3 normal use conversion plugconversion plug intended for normal use3.4 rough use conversion plugconversion plug designed to withstand severe mechanical handlingNOTE Rough-use conversion p

40、lugs are identified by additional marking inaccordance with 7.1c). They are not intended for gross misuse, e.g. withdrawal froma socket-outlet by pulling on the flexible cable.3.5 reusable conversion plugconversion plug the intended use of which is on one non-BS 1363 type plugonly, and which is:BRIT

41、ISH STANDARDBS 1363-5:20162 The British Standards Institution 2016 able to be reused without damaging either the non-BS 1363 type plugwhich was housed in it, a new non-BS 1363 type plug or itself; designed such that the non-BS 1363 type plug can only be removed by theuse of a tool; deemed as low use

42、 in terms of removal from and refitting to anon-BS 1363 type plugNOTE Low use is less than ten removal and refitting operations during theconversion plug lifetime.3.6 non-reusable conversion plugconversion plug, the intended use of which is on one non-BS 1363 type plugonly and which cannot be remove

43、d without rendering it unfit for use3.7 accessible external surfaces of a conversion plugall surfaces that can be touched by test probe B specified inBS EN 61032:1998 when a conversion plug is in full engagement with acorresponding socket-outlet3.8 engagement surface of a conversion plugsurface that

44、 cannot be touched by test probe B specified inBS EN 61032:1998 when a conversion plug is in full engagement with acorresponding socket-outlet3.9 live partscurrent-carrying parts and those metal parts in contact with them during normaluseNOTE Metal parts of the earthing circuit are not considered to

45、 be current-carryingparts.3.10 fuse carriermovable or removable part designed to carry, retain, cover, and/or remove thefuse-link3.11 type testtest or series of tests made on a type test sample, for the purpose of checkingconformity of the design of a given product to the requirements of the relevan

46、tstandard3.12 type test samplesample consisting of one or more similar units or specimens submitted by themanufacturer or responsible vendor for the purpose of type test3.13 fine wire thermocouplethermocouple having wires not exceeding 0.3 mm in diameter3.14 calibrated linkcalibrated heat source for

47、 use in place of a fuse-link during temperature risetests3.15 indicator lamp (pilot lamp)lamp or similar device that illuminates to indicate that the conversion plug isenergized3.16 resilient materialmaterial having the inherent capability of regaining or substantially regaining itsoriginal form whe

48、n deforming loads are removedBRITISH STANDARD BS 1363-5:2016 The British Standards Institution 2016 33.17 creepage distanceshortest distance along the surface of the insulating material between twoconductive parts3.18 clearanceshortest distance in air between two conductive parts3.19 retentionpart o

49、f the conversion plug that is deemed to have an active part in theretention of the non-BS 1363 type plug within the body of the conversion plug3.20 dangerous compatibilityunsafe condition that occurs when a conversion plug allows a non-BS 1363 typeplug of a higher current rating or different voltage rating than that of theconversion plug to be fitted, and/or when a class I non-BS 1363 type plug couldbe fitted into a class II conversion plug3.21 insulated s