BS 1363-5-2008 13 A plugs socket-outlets adaptors and connection units - Specification for fused conversion plugs《13A插头、电源插座、适配器和连接装置 装有保险丝的转换插头用规范》.pdf

《BS 1363-5-2008 13 A plugs socket-outlets adaptors and connection units - Specification for fused conversion plugs《13A插头、电源插座、适配器和连接装置 装有保险丝的转换插头用规范》.pdf》由会员分享，可在线阅读，更多相关《BS 1363-5-2008 13 A plugs socket-outlets adaptors and connection units - Specification for fused conversion plugs《13A插头、电源插座、适配器和连接装置 装有保险丝的转换插头用规范》.pdf（84页珍藏版）》请在麦多课文档分享上搜索。

1、BS 1363-5:200813 A plugs, socket-outlets, adaptors and connection units Part 5: Specification for fused conversion plugsICS 29.120.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPublishing and copyright informationThe BSI copyright notice displayed in this do

2、cument indicates when the document was last issued. BSI 2008ISBN 978 0 580 53655 7The following BSI references relate to the work on this standard:Committee reference PEL/23Draft for comment 06/30159706 DCPublication historyFirst published August 2008Amendments issued since publicationAmd. no. Date

3、Text affectedBS 1363-5:2008 BSI 2008 iBS 1363-5:2008ContentsForeword iii1 Scope 12 Normative references 23 Terms and definitions 24 Classification 65 General requirements 66 Testing regime 67 Marking and labelling 88 Clearances, creepage distances, and solid insulation 109 Accessibility of live part

4、s 1510 Provision for earthing 1611 Contacts in conversion plugs 1712 Construction of conversion plugs 1713 (Not used) 2914 Resistance to ageing and to humidity 2915 Insulation resistance and electric strength 3116 Temperature rise 3217 (Not used) 3318 (Not used) 3319 Connection of the non-BS 1363 ty

5、pe plug and non-BS 1363 type plug retention in conversion plugs 3420 Mechanical strength 3821 Screws, current-carrying parts and connections 3922 Resistance to heat 4023 Resistance to abnormal heat and fire 4124 Resistance to excessive residual stresses and to rusting 4325 (Not used) 44AnnexesAnnex

6、A (normative) The construction and calibration of a calibrated link 68Annex B (normative) Measurement of clearances and creepage distances 69Annex C (normative) Determination of the comparative tracking index (CTI) and proof tracking index (PTI) 74Annex D (normative) Relationship between rated impul

7、se withstand voltage, rated voltage and overvoltage category 74Annex E (informative) Pollution degree 75Annex F (normative) Impulse voltage 75Bibliography 77List of figuresFigure 1 Test pin (see Clause 12) 44Figure 2a Apparatus for mechanical strength test on resilient covers (see Clause 9) 45Figure

8、 2b Hardwood block for Figure 2a) 46Figure 4a Dimensions and disposition of pins (see Clause 12) 47Figure 4b Concave shrinkage allowance for ISODs 49Figure 5 Gauge for conversion plug pins (see Clauses 12, 20 and 22) 51Figure 6 Apparatus for testing conversion plug cover fixing screws (see Clause 12

9、) 52Figure 7 Mounting plate (see Clause 12) 53BS 1363-5:2008ii BSI 2008Figure 8 Plug pin deflection test apparatus for resilient conversion plugs (see Clause 12) 54Figure 9 Apparatus for abrasion test on insulating sleeves of plug pins (see Clause 12) 55Figure 10 Apparatus for abrasion test on insul

10、ating sleeves of plug pins (see Clause 12) 56Figure 11 GO gauge for socket-outlet for use when checking Figure 17b) 57Figure 17a Test apparatus for temperature rise test (see Clause 16) 58Figure 17b Dummy front plate for temperature rise test (see Clause 16) 59Figure 18 Apparatus for flexing test (s

11、ee Clause 19) 60Figure 19 Solid link for test on fuse clips (see Clause 20) 60Figure 20 Tumbling barrel (see Clause 20) 61Figure 23 Apparatus for pressure test (see Clause 20) 62Figure 24 Apparatus for ball pressure test (see Clause 22) 63Figure 28 Calibrated link (see A.1) 64Figure 29 Calibration j

12、ig for calibrated link (see A.2) 65Figure 32 Apparatus for tests on conversion plug pins (see Clause 12) 66Figure 33 Apparatus for torsion test on pins (see Clause 12) 67List of tablesTable 1 Schedule of tests 7Table 2 Rated current and maximum fuse rating in normal use, and load for flexing and cor

13、d grip tests related to size of flexible cord 9Table 3 Minimum clearances for basic insulation 12Table 4 Minimum creepage distances for basic insulation 13Table 5 Withstand voltages for insulation types 14Table 6 Permitted temperature rises 32Table 7 Torque values for screws and nuts 35Table 8 Plug

14、displacement test loads 35Table 9 Application of glow-wire test 42Table B.1 Minimum values of width, X 69Table D.1 Rated impulse withstand voltage for conversion plug energized directly from the low voltage mains 74Table F.1 Test voltages for verifying clearances at sea level 76Summary of pagesThis

15、document comprises a front cover, an inside front cover, pages i to iv, pages 1 to 77 and a back cover. BSI 2008 iiiBS 1363-5:2008ForewordPublishing informationThis part of BS 1363 was published by BSI and came into effect on 29 August 2008. It was prepared by Technical Committee PEL/23, Electrical

16、accessories. A list of organizations represented on this committee can be obtained on request to its secretary.Relationship with other publicationsBS 1363 comprises five parts covering the following.Part 1: Specification for rewireable and non-rewireable 13 A fused plugs;Part 2: Specification for 13

17、 A switched and unswitched socket-outlets;Part 3: Specification for adaptors;Part 4: Specification for 13 A fused connection units switched and unswitched;Part 5: Specification for fused conversion plugs.Presentational conventionsThe provisions of this standard are presented in roman (i.e. upright)

18、type. Its requirements are expressed in sentences in which the principal auxiliary verb is “shall”.Commentary, explanation, and general informative material is presented in smaller italic type, and does not constitute a normative element.Contractual and legal considerationsThis publication does not

19、purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.iv BSI 2008 This page deliberately left blankBS 1363-5:2008 BSI 2008 1BS 1363-5:20081 ScopeThis Part of BS

20、 1363 specifies requirements, with particular reference to safety in normal use, for 13 A, fused, conversion plugs for household, commercial and light industrial purposes.The scope of the standard covers two-pole plus earth conversion plugs that are either reusable or non-reusable and that are suita

21、ble for the connection of non-BS 1363 type plugs, conforming to a recognized standard, to socket-outlets conforming to BS 1363-2. The scope of this standard is limited to devices with the following characteristics: that have insulating sleeves on line and neutral pins; that have one plug portion and

22、 one set of contacts intended to connect to a non-BS 1363 type plug that conforms to the dimensional requirements of a standard listed in IEC TR 60083; that are suitable for the connection of electrical equipment in a.c. circuits only, operating at voltages not exceeding 250 V r.m.s. at 50 Hz; that

23、may have the un-terminated metal earth pin replaced with a similarly dimensioned insulated shutter opening device (ISOD) designed to operate the shutter mechanism of a socket-outlet conforming to BS 1363-2.NOTE A metal earth pin can be brass, copper, phosphor-bronze or other metal at least equivalen

24、t with regard to its conductivity, resistance to abrasion, and resistance to corrosion.Two categories of conversion plugs are specified, covering normal and rough use.Conversion plugs specified in this standard are intended for the connection of loads to socket outlets; they are not intended for the

25、 connection of electrical power generators to socket outlets.Conversion plugs incorporating switches, transformers, thermostats, or other control means are outside the scope of this Part of BS 1363.This standard also does not cover: non-BS 1363 type conversion plugs, i.e. with a contact set to fit 1

26、3 A plugs, and a male plug portion suitable for a non-BS 1363 type socket outlet; or adaptors (as to which, see BS 1363-3).BS 1363-5:20082 BSI 20082 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition c

27、ited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.BS 923-1, Guide on high-voltage testing techniques Part 1: GeneralBS 1362, Specification for general purpose fuse links for domestic and similar purposes (primarily for use in plugs

28、) BS 1363-2:1995+A3:2007, 13 A plugs, socket-outlets, adaptors and connection units Pt 2: Specification for 13 A switched and unswitched socket-outletsBS 4662:2006, Boxes for flush mounting of electrical accessories Requirements and test methods and dimensionsBS EN 10270-1:2001, Steel wire for mecha

29、nical springs Part 1: Patented cold drawn unalloyed spring steel wireBS EN 60112:2003, Method for the determination of the proof and the comparative tracking indices of solid insulating materialsBS EN 60664-1:2007, Insulation coordination for equipment within low-voltage systems Part 1: Principles,

30、requirements and testsBS EN 60695-2-11, Fire hazard testing Part 2-11: Glowing/hot-wire based test methods Glow-wire flammability test method for end-productsBS EN 60695-10-2, Fire hazard testing Part 10-2: Abnormal heat Ball pressure testBS EN 61032:1998, Protection of persons and equipment by encl

31、osures Probes for verificationBS EN ISO 9453, Soft solder alloys Chemical compositions and formsIEC TR 60083, Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC3 Terms and definitionsFor the purposes of this Part of BS 1363, the following terms and

32、definitions apply.NOTE Where the terms voltage and current are used, they imply r.m.s. values, unless otherwise stated.3.1 conversion plugfused device that can be engaged with a socket-outlet conforming to BS 1363-2, and that is designed to enclose the non-BS 1363 type plug and enables it to be enga

33、ged with such a socket-outlet3.2 normal useconditions during use which: do not exceed the conditions intended by the manufacturer; are not excessive, rough use or gross misuse; do not exceed reasonably foreseeable conditions of misuse BSI 2008 3BS 1363-5:20083.3 normal use conversion plugconversion

34、plug intended for normal use 3.4 rough use conversion plugconversion plug designed to withstand severe mechanical handlingNOTE Rough use conversion plugs are identified by additional marking in accordance with 7.1 c). They are not intended for gross misuse, e.g. withdrawal from a socket-outlet by pu

35、lling on the flexible cord.3.5 reusable conversion plug conversion plug the intended use of which is on one non-BS 1363 type plug only, and which is: able to be reused without damaging either the non-BS 1363 type plug which was housed in it, a new non-BS1363 type plug or itself; designed such that t

36、he non-BS 1363 type plug can only be removed by the use of a tool; deemed as low use in terms of removal from and refitting to a non-BS 1363 type plugNOTE Low use is less than 10 removal and refitting operations during the conversion plug lifetime.3.6 non-reusable conversion plug conversion plug the

37、 intended use of which is on one non-BS 1363 type plug only and which cannot be removed without rendering it unfit for use3.7 accessible external surfaces of a conversion plugall surfaces that can be touched by test probe B specified in BS EN 61032:1998 when a conversion plug is in full engagement w

38、ith a corresponding socket-outlet 3.8 engagement surface of a conversion plug surface that cannot be touched by test probe B specified in BS EN 61032:1998 when a conversion plug is in full engagement with a corresponding socket-outlet3.9 live partscurrent-carrying parts and those metal parts in cont

39、act with them during normal useNOTE Metal parts of the earthing circuit are not considered to be current-carrying parts.3.10 fuse carriermovable or removable part designed to carry, retain, cover, and/or remove the fuse link3.11 type test test or series of tests made on a type test sample, for the p

40、urpose of checking conformity of the design of a given product to the requirements of the relevant standard3.12 type test sample sample consisting of one or more similar units or specimens submitted by the manufacturer or responsible vendor for the purpose of type test3.13 fine wire thermocouplether

41、mocouple having wires not exceeding 0.3 mm in diameterBS 1363-5:20084 BSI 20083.14 calibrated linkcalibrated heat source for use in place of a fuse link during temperature rise tests3.15 indicator lamp (pilot lamp)lamp or similar device that illuminates to indicate that the conversion plug is energi

42、zed3.16 resilient materialmaterial having the inherent capability of regaining or substantially regaining its original form when deforming loads are removed3.17 creepage distanceshortest distance along the surface of the insulating material between two conductive parts3.18 clearanceshortest distance

43、 in air between two conductive parts3.19 retentionpart of the conversion plug that is deemed to have an active part in the retention of the non-BS 1363 type plug within the body of the conversion plug3.20 dangerous compatibilityunsafe condition that occurs when a conversion plug allows a non-BS 1363

44、 type plug of a higher current rating or different voltage rating than that of the conversion plug to be fitted, and/or when a class I non-BS 1363 type plug could be fitted into a class II conversion plug3.21 insulated shutter-opening device (ISOD) protrusion from the engagement surface of the plug,

45、 in place of the brass earth pin, made of insulating material having dimensions similar to those of a brass earth pin3.22 basic insulationinsulation applied to live parts to provide basic protection against electric shockNOTE Basic insulation does not necessarily include insulation used exclusively

46、for functional purposes.3.23 supplementary insulation independent insulation applied in addition to the basic insulation, in order to provide protection against electric shock in the event of the failure of basic insulation3.24 reinforced insulationsingle insulation system applied to live parts, tha

47、t provides a degree of protection against electric shock equivalent to double insulation under the conditions specified in the relevant standard3.25 functional insulationinsulation between conductive parts that is necessary only for the proper functioning of the equipment BSI 2008 5BS 1363-5:20083.2

48、6 class Ia method of protection against electric shock which does not rely on basic insulation only, but which includes means for the connection of exposed-conductive-parts to a protective conductor in the fixed wiring of the installation3.27 class IImethod of protection against electric shock which

49、 does not rely on basic insulation only, but in which additional safety precautions, such as double insulation or reinforced insulation are provided, there being no provision for protective earthing or reliance upon installation conditionsNOTE 1 Such a method may be one of the following.a) Equipment having double and substantially continuous enclosure of insulation material which envelop