BS 1363-2-2016 13 A plugs socket-outlets adaptors and connection units Part 2 Specification for 13 A switched and unswitched socket-outlets《13 A插头、电源插座、适配器和连接装置 第2部分 13 A有开关和无开关电源插.pdf

《BS 1363-2-2016 13 A plugs socket-outlets adaptors and connection units Part 2 Specification for 13 A switched and unswitched socket-outlets《13 A插头、电源插座、适配器和连接装置 第2部分 13 A有开关和无开关电源插.pdf》由会员分享，可在线阅读，更多相关《BS 1363-2-2016 13 A plugs socket-outlets adaptors and connection units Part 2 Specification for 13 A switched and unswitched socket-outlets《13 A插头、电源插座、适配器和连接装置 第2部分 13 A有开关和无开关电源插.pdf（94页珍藏版）》请在麦多课文档分享上搜索。

1、BS 1363-2:2016 13 A plugs, socket-outlets, adaptors and connection units Part 2: Specification for 13 A switched and unswitched socket-outlets BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Publishing and copyright information The BSI copyright notice displayed in

2、this document indicates when the document was last issued. The British Standards Institution 2016 Published by BSI Standards Limited 2016 ISBN 978 0 580 85810 9 ICS 29.120.30 The following BSI references relate to the work on this document: Committee reference PEL/23 Draft for comment 15/30297234 DC

3、 Publication history First published as BS 1363, September 1967 Second edition, August 1984 First published as Part 2, February 1995 Second (present) edition, August 2016 Amendments issued since publication Date Text affected BS 1363-2:2016 BRITISH STANDARDContents Foreword iii 1 Scope 1 2 Condition

4、s of use 1 3 Terms and definitions 2 4 General 5 5 General conditions for type testing 5 6 Classification and rating 7 7 Marking and labelling 8 8 Clearances, creepage distances and solid insulation 10 9 Accessibility of live parts 14 10 Provisions for earthing 15 11 Terminals and terminations 16 12

5、 (Not used) 20 13 Construction of socket-outlets 20 14 Resistance to ageing, resistance to humidity and protection provided by enclosures 27 15 Insulation resistance and electric strength 30 16 Temperature rise 31 17 Breaking capacity of socket-outlets 34 18 Normal operation of socket-outlets 35 19

6、Connection of flexible cables and cable anchorage 36 20 Mechanical strength 38 21 Screws, current-carrying parts and connections 40 22 Resistance to heat 41 23 Resistance to abnormal heat and fire 42 24 Resistance to excessive residual stresses and to rusting 43 25 (Not used) 44 26 Cyclic loading te

7、st 44 Annexes Annex A (normative) The construction and calibration of a calibrated link 69 Annex B (normative) Measurement of clearances and creepage distances 70 Annex C (normative) Determination of the Comparative Tracking Index (CTI) and Proof Tracking Index (PTI) 74 Annex D (normative) Relation

8、between rated impulse withstand voltage, rated voltage and Overvoltage Category 74 Annex E (normative) Pollution degree 75 Annex F (normative) Impulse voltage test 75 Annex G (normative) Test plug for temperature-rise test 76 Annex H (informative) Specific structure of BS EN 50525 and its derivation

9、 from British Standards and from HD 21 and HD 22 (BS EN 50525-1:2011, National Annex NA) 77 Annex I (normative) Requirements for incorporated electronic components 78 Bibliography 83 List of figures Figure1T e s tp i n(see Clause 12) 45 Figure 2a Apparatus for mechanical strength test on resilient c

10、overs (see Clause 9) 46 Figure 2b Hardwood block for Figure 2a 47 Figure 3 Disposition of socket contacts (see Clause 13) 48 Figure 11 GO gauge for socket-outlet (see Clause 13) 49 Figure 12 Contact test gauge (see Clause 13) 50 Figure 13 Test apparatus and circuit for use with contact and non conta

11、ct gauges (see Clause 13) 51 Figure 14 Non contact test gauge (see Clause 13) 52 Figure 15 Turning moment gauge (see Clause 13) 53 BRITISH STANDARD BS 1363-2:2016 The British Standards Institution 2016 iFigure 16a Withdrawal pull gauges for effectiveness of contact: Gauge for earthing socket contact

12、 (see Clause 13) 54 Figure 16b Withdrawal pull gauges for effectiveness of contact: Gauge for line and neutral current-carrying socket contacts (see Clause 13) 55 Figure 18 Apparatus for flexing test (see Clause 19) 56 Figure 19 Solid link for test on fuse clips (see Clause 20) 57 Figure 20 Tumbling

13、 barrel (see Clause 20) 57 Figure 21a Pendulum impact test: General view of apparatus (see Clause 20) 58 Figure 21b Pendulum impact test: Constructional details of striking elements (see Clause 20) 59 Figure 21c Pendulum impact test: Constructional details of mounting support for test samples (see C

14、lause 20) 60 Figure 22 Arrangements for mechanical strength test for portable socket outlets (see Clause 20) 61 Figure 23 Apparatus for pressure test (see Clause 22) 62 Figure 28 Calibrated link (see A.1) 64 Figure 29 Calibration jig for calibrated link (see A.2) 65 Figure 30 Test plug for temperatu

15、re rise (see Annex G) 67 Example 1 71 Example 2 71 Example 3 71 Example 4 71 Example 5 72 Example 6 72 Example 7 72 Example 8 72 Example 9 73 Example 10 73 Example 11 74 List of tables Table 1 Schedule of tests 6 Table 2 Rated current and maximum fuse rating in normal use, and load for flexing and f

16、lexible cable grip tests related to size of flexible cable 9 Table 3 Minimum clearances for basic insulation 12 Table 4 Minimum creepage distances (mm) for basic insulation 13 Table 5 Withstand voltages for insulation types 14 T a b l e6T orque values for screws and nuts 16 Table 7 Actuator test for

17、ce 23 T a b l e8T ightening torque values for cable glands 29 Table 9 Permitted temperature rises 32 Table 10 Loading of socket-outlets for temperature-rise test 33 Table 11 Connection of flexible cables 37 Table 12 Application of glow-wire test 43 Table B.1 Minimum values of widthX7 0 Table D.1 Rat

18、ed impulse withstand voltage for socket-outlets energized directly from the low voltage mains 74 Table F.1 Test voltages for verifying clearances at sea level 76 Table H.1 Specific structure of BS EN 50525 and its derivation from British Standards and from HD 21 and HD 22 (BS EN 50525-1:2011, Nation

19、al Annex NA) 77 Summary of pages This document comprises a front cover, an inside front cover, pages i to iv, pages 1 to 86, an inside back cover and a back cover. BRITISH STANDARD BS 1363-2:2016 ii The British Standards Institution 2016Foreword Publishing information This part of BS 1363 is publish

20、ed by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 31 August 2016. It was prepared by Technical Committee PEL/23, Electrical accessories. A list of organizations represented on this committee can be obtained on request to its secretary. Superse

21、ssion This part of BS 1363 supersedes BS 1363-2:1995+A4:2012, which remains current and will be withdrawn on 31 August 2019. Information about this document BS 1363 comprises five parts covering the following: Part 1: Specification for rewirable and non-rewirable 13 A fused plugs; Part 2: Specificat

22、ion for 13 A switched and unswitched socket-outlets; Part 3: Specification for adaptors; Part 4: Specification for 13 A fused connection units switched and unswitched; Part 5: Specification for fused conversion plugs. NOTE In order to prevent confusion with BS 1363:1984, the figure and clause number

23、s have been retained. The structure of BS EN 50525 and its derivation from British Standards and HD 21 and HD 22 is set out in BS EN 50525-1:2011, National Annex NA. This is reproduced in Annex H for the convenience of users of this part of BS 1363. This new edition of BS 1363-2 incorporates technic

24、al changes only. It does not represent a full review or revision of the standard, which will be undertaken in due course.This new edition of BS 1363-2 incorporates Annex I (normative) which provides requirements for incorporated electronic components. Presentational conventions The provisions of thi

25、s standard are presented in roman (i.e. upright) type. Its requirements are expressed in sentences in which the principal auxiliary verb is shall. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element. Requirements i

26、n this standard are drafted in accordance with Rules for the structure and drafting of UK standards, subclause J.1.1, which states, Requirements should be expressed using wording such as: When tested as described in Annex A, the product shall . This means that only those products that are capable of

27、 passing the specified test will be deemed to conform to this standard. BRITISH STANDARD BS 1363-2:2016 The British Standards Institution 2016 iiiContractual and legal considerations This publication does not purport to include all the necessary provisions of a contract. Users are responsible for it

28、s correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Particular attention is drawn to the following specific regulations: The Plugs and Sockets etc. (Safety) Regulations 1994. SI No. 1768. BRITISH STANDARD BS 1363-2:2016 iv The British Standards In

29、stitution 20161 Scope This part of BS 1363 specifies requirements for 13 A switched and unswitched shuttered socket-outlets for household, commercial and light industrial purposes, with particular reference to safety in normal use. The socket-outlets are suitable for the connection of appliances, so

30、und-vision equipment, luminaires, etc. in a.c. circuits only, operating at voltages not exceeding 250 V r.m.s. at 50 Hz using plugs in accordance with BS 1363-1:2016. Additional requirements are included for socket-outlets suitable for electric vehicle charging. Requirements are specified for 13 A s

31、huttered socket-outlets in single or multiple arrangements, with or without associated controlling switches, for flush mounting in suitable boxes, e.g. conforming to BS 4662:2006+A1:2009, or for surface or panel mounting or for portable use. Fixed socket-outlets are intended for use with cables conf

32、orming to BS 6004:2012 and cables to the relevant part of BS EN 50525 (see Annex H), having copper conductors. Portable socket-outlets are intended for use with flexible cables conforming to the relevant part of BS EN 50525. Socket-outlets incorporating fuse links, switches and indicator lamps are i

33、ncluded within the scope of this part of BS 1363. Socket-outlets incorporating electronic components as detailed in Annex I are included within the scope of this part of BS 1363. Socket-outlets conforming to this standard are shuttered and therefore do not require the use of additional means to shie

34、ld the current-carrying contacts when no plug is present in the socket-outlet. NOTE 1 The titles of the publications referred to in this part of BS 1363 are listed in the bibliography. NOTE 2 In order to maintain safety and interchangeability with plugs and socket-outlets it is necessary that these

35、products conform to the requirements of Clause 9 and Clause 13 of this part of BS 1363, however their body outline need not be limited at a distance of 6.35 mm from the plug engagement surface. NOTE 3 Requirements for electromagnetic compatibility for socket-outlets that incorporate electronic devic

36、es are given in Annex I. A socket-outlet that does not incorporate electronic devices does not emit intolerable electromagnetic interference since significant electromagnetic disturbances are only generated during insertion and withdrawal which are not continuous. A socket-outlet that does not incor

37、porate electronic devices is mechanical by nature of construction. The product is therefore immune from electromagnetic interference. 2 Conditions of use Socket-outlets shall be suitable for use under the following conditions: a) an ambient temperature in the range 5 C to +40 C, the average value ov

38、er 24 h not exceeding 25 C; NOTE Under normal conditions of use, the available cooling air is subject to natural atmospheric variations of temperature and hence the peak temperature occurs only occasionally during the hot season, and on those days when it does occur it does not persist for lengthy p

39、eriods. b) a situation not subject to exposure to direct radiation from the sun or other source of heat likely to raise temperatures above the limits specified in a); c) an altitude not exceeding 2 000 m above sea level; d) an atmosphere not subject to abnormal pollution by smoke, chemical fumes or

40、other abnormal conditions. This is equivalent to pollution degree 2, (see Annex E) and Overvoltage Category III (see Annex D). BRITISH STANDARD BS 1363-2:2016 The British Standards Institution 2016 13 Terms and definitions For the purposes of this part of BS 1363 the following terms and definitions

41、apply. NOTE Where the terms voltage and current are used, they imply r.m.s. values, unless otherwise stated. 3.1 socket-outlet an accessory having a set of three socket-contacts designed to engage with the pins of a corresponding plug and having means for the electrical connection of appropriate fle

42、xible cables and may include its dedicated enclosure 3.2 fixed socket-outlet a socket-outlet which with its associated enclosure is intended for use mounted in or on a fixed surface 3.3 surface-mounted socket-outlet a socket-outlet which is intended to be mounted on a wall or other flat surface with

43、out the need for recessing 3.4 flush-mounted socket-outlet a socket-outlet which is intended to be mounted in a box which is recessed into a wall or other flat surface NOTE The socket-outlet plate and the socket-outlet base are regarded as forming a complete unit, and the socket-outlet plate is moun

44、ted with its back either flush with a wall or other flat-surface structure, or flush with the front of a socket-outlet box or enclosure. 3.5 panel-mounted socket-outlet a socket-outlet intended for incorporation into equipment panels or electrical trunking and which depends upon such incorporation f

45、or its enclosure 3.6 portable socket-outlet a socket-outlet intended to be connected to, or integral with, a flexible cable, and which can easily be moved from one place to another while connected to the supply 3.7 rewirable portable socket-outlet a portable socket-outlet so constructed that a flexi

46、ble cable can be fitted or replaced using general purpose tools 3.8 non-rewirable portable socket-outlet a portable socket-outlet so constructed that if forms a complete unit with the flexible cable which cannot be replaced after assembly by the manufacturer of the portable socket-outlet NOTE See al

47、so 13.18. 3.9 moulded-on portable socket-outlet a non-rewirable portable socket-outlet, the manufacture of which is completed by insulating material moulded around pre-assembled component parts and the terminations of the flexible cable 3.10 fused socket-outlet a socket-outlet having provision for a

48、 replaceable cartridge fuse link 3.11 switched socket-outlet a socket-outlet with an associated switch to disconnect the supply to the line socket contact or to both line and neutral socket contacts BRITISH STANDARD BS 1363-2:2016 2 The British Standards Institution 20163.12 multiple socket-outlet a

49、 combination of two or more socket-outlets 3.13 socket-outlet base that part of the socket-outlet which carries the contacts NOTE It may be integral with the socket-outlet plate. 3.14 socket-outlet plate the external plate which covers the base and contact assembly of a socket-outlet and through which the pins of the plug are inserted 3.15 socket-outlet box a box suitable for mounting one or more socket-outlets 3.16 shutter a movable device arranged to shield the current-ca