ASTM F2245-2007 Standard Specification for Design and Performance of a Light Sport Airplane《轻型运动飞机的设计和性能用标准规范》.pdf

《ASTM F2245-2007 Standard Specification for Design and Performance of a Light Sport Airplane《轻型运动飞机的设计和性能用标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2245-2007 Standard Specification for Design and Performance of a Light Sport Airplane《轻型运动飞机的设计和性能用标准规范》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 2245 07Standard Specification forDesign and Performance of a Light Sport Airplane1This standard is issued under the fixed designation F 2245; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers airworthiness requirements forthe design of powered fixed wing light sport aircraft, an“airplane.”1.2 Thi

3、s specification is applicable to the design of a lightsport aircraft/airplane as defined by regulations and limited toVFR flight.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish

4、 appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.2. Referenced Documents2.1 ASTM Standards:2F 2316 Specification for Airframe Emergency Parachutesfor Light Sport AircraftF 2339 Practice for Design and Manufacture of Reciprocat-ing Spa

5、rk Ignition Engines for Light Sport Aircraft2.2 Federal Aviation Regulations:3FAR-33 Airworthiness Standards: Aircraft Engines2.3 Joint Aviation Requirements:4JAR-E EnginesJAR-22 Sailplanes and Powered Sailplanes3. Terminology3.1 Definitions:3.1.1 flapsany movable high lift device.3.1.2 maximum empt

6、y weight, WE(N)largest emptyweight of the airplane, including all operational equipment thatis installed in the airplane: weight of the airframe, powerplant,required equipment, optional and specific equipment, fixedballast, full engine coolant and oil, hydraulic fluid, and theunusable fuel. Hence, t

7、he maximum empty weight equalsmaximum takeoff weight minus minimum useful load: WE= W WU.3.1.3 minimum useful load, WU(N)where WU= W WE.3.1.4 nighthours between the end of evening civil twilightand the beginning of morning civil twilight.3.1.4.1 DiscussionCivil twilight ends in the evening whenthe c

8、enter of the suns disc is 6 degrees below the horizon, andbegins in the morning when the center of the suns disc is 6degrees below the horizon.3.2 Abbreviations:3.2.1 ARaspect ratio = b2/S3.2.2 bwing span, (m)3.2.3 cchord, (m)3.2.4 CAScalibrated air speed, (m/s, kts)3.2.5 CLlift coefficient of the a

9、irplane3.2.6 CDdrag coefficient of the airplane3.2.7 CGcenter of gravity3.2.8 Cmmoment coefficient (Cmis with respect to c/4point, positive nose up)3.2.9 CMOzero lift moment coefficient3.2.10 Cnnormal coefficient3.2.11 gacceleration as a result of gravity = 9.81 m/s23.2.12 IASindicated air speed (m/

10、s, kts)3.2.13 ICAOInternational Civil Aviation Organization3.2.14 LSAlight sport aircraft3.2.15 MACmean aerodynamic chord (m)3.2.16 nload factor3.2.17 n1airplane positive maneuvering limit load factor3.2.18 n2airplane negative maneuvering limit load factor3.2.19 n3load factor on wheels3.2.20 Ppower,

11、 (kW)3.2.21 rair density (kg/m3) = 1.225 at sea level standardconditions3.2.22 POHPilot Operating Handbook3.2.23 qdynamic pressure (N/m2)= 1/2rV23.2.24 RCclimb rate (m/s)3.2.25 Swing area (m2)3.2.26 Vairspeed (m/s, kts)3.2.27 VAdesign maneuvering speed3.2.28 VCdesign cruising speed3.2.29 VDdesign di

12、ving speed3.2.30 VDFdemonstrated flight diving speed (VDF# VD)1This specification is under the jurisdiction of ASTM Committee F37 on LightSport Aircraft and is the direct responsibility of Subcommittee F37.20 on Airplane.Current edition approved Feb. 1, 2007. Published March 2007. Originallyapproved

13、 in 2004. Last previous edition approved in 2006 as F 2245 06.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website

14、.3Available from Federal Aviation Administration (FAA), 800 IndependenceAve., SW, Washington, DC 20591, http:/www.faa.gov.4Available from Global Engineering Documents, 15 Inverness Way, EastEnglewood, CO 80112-5704, http:/.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Consh

15、ohocken, PA 19428-2959, United States.3.2.31 VFdesign flap speed3.2.32 VFEmaximum flap extended speed3.2.33 VHmaximum speed in level flight with maximumcontinuous power (corrected for sea level standard conditions)3.2.34 VNEnever exceed speed (VH# VNE# 0.9VDF)3.2.35 VSstalling speed or minimum stead

16、y flight speed atwhich the airplane is controllable (flaps retracted)3.2.36 VS1stalling speed or minimum steady flight speedwith the flaps in a specific configuration3.2.37 VS0stalling speed or minimum steady flight speedat which the airplane is controllable in the landing configura-tion (flaps full

17、y deployed)3.2.38 VSPmaximum spoiler/speed brake extended speed3.2.39 VRground gust speed3.2.40 VXspeed for best angle of climb3.2.41 VYspeed for best rate of climb3.2.42 Wmaximum takeoff or maximum design weight(N)3.2.43 WEmaximum empty airplane weight (N)3.2.44 WUminimum useful load (N)3.2.45 wave

18、rage design surface load (N/m2)4. Flight4.1 Proof of Compliance:4.1.1 Each of the following requirements shall be met at themost critical weight and CG configuration. Unless otherwisespecified, the speed range from stall to VDFor the maximumallowable speed for the configuration being investigated sh

19、allbe considered.4.1.1.1 VDFmay be less than or equal to VD.4.1.1.2 If VDFchosen is less than VD, VNEmust be less thanor equal to 0.9VDFand greater than or equal to 1.1VC.4.1.2 The following tolerances are acceptable during flighttesting:Weight +5 %, 10 %Weight, when critical +5 %, 1 %CG 67 % of tot

20、al travel4.2 Load Distribution Limits:4.2.1 Minimum Useful Load Requirement:4.2.1.1 For a single-place airplane:WU5 845 1 3P, N!where:P = rated engine power, kW.4.2.1.2 For a two-place airplane:WU5 1690 1 3P, N!where:P = rated engine power, kW.4.2.2 Minimum flying weight shall be determined.NOTE 1Fo

21、r reference, standard occupant weight = 845 N (190 lb). Forthe minimum flying weight, standard occupant weight = 534 N (120 lb).Fuel density = 0.72 kg/L (7 N/L; 6 lb/U.S. gal).4.2.3 Empty CG, most forward, and most rearward CG shallbe determined.4.2.4 Fixed or removable ballast, or both, may be used

22、 ifproperly installed and placarded.4.3 Propeller Speed and Pitch LimitsPropeller configura-tion shall not allow the engine to exceed safe operating limitsestablished by the engine manufacturer under normal condi-tions.4.3.1 Maximum RPM shall not be exceeded with fullthrottle during takeoff, climb,

23、or flight at 0.9VH, and 110 %maximum continuous RPM shall not be exceeded during aglide at VNEwith throttle closed.4.4 Performance, GeneralAll performance requirementsapply in standard ICAO atmosphere in still air conditions andat sea level. Speeds shall be given in indicated (IAS) andcalibrated (CA

24、S) airspeeds.4.4.1 Stalling SpeedsWing level stalling speeds VSOandVSshall be determined by flight test at a rate of speed decreaseof 1 kts/s or less, throttle closed, with maximum takeoffweight, and most unfavorable CG.4.4.2 TakeoffWith the airplane at maximum takeoffweight, full throttle, the foll

25、owing shall be measured usingnormal takeoff procedures:NOTE 2The procedure used for normal takeoff, including flap posi-tion, shall be specified within the POH.4.4.2.1 Ground roll distance to takeoff on a runway withminimal grade.4.4.2.2 Distance to clear a 15-m (50-ft) obstacle at a climbspeed of a

26、t least 1.3VS1.4.4.3 ClimbAt maximum takeoff weight, flaps in theposition specified for climb within the POH, and full throttle:4.4.3.1 Rate of climb at VYshall exceed 95 m/min (312fpm).4.4.3.2 Climb gradient at VXshall exceed112 .4.4.4 LandingFor landing with throttle closed and flapsextended, the

27、following shall be determined:4.4.4.1 Landing distance from 15 m (50 ft) above groundwhen speed at 15 m (50 ft) is 1.3VSO.4.4.4.2 Ground roll distance with reasonable braking if soequipped.4.4.5 Balked LandingThe airplane shall demonstrate afull-throttle climb gradient at 1.3VSOwhich shall exceed130

28、within5sofpower application from aborted landing. If theflaps may be promptly and safely retracted without loss ofaltitude and without sudden changes in attitude, they may beretracted.4.5 Controllability and Maneuverability:4.5.1 General:4.5.1.1 The airplane shall be safely controllable and maneu-ve

29、rable during takeoff, climb, level flight (cruise), dive to VDFor the maximum allowable speed for the configuration beinginvestigated, approach, and landing (power off and on, flapsretracted and extended) through the normal use of primarycontrols.4.5.1.2 Smooth transition between all flight conditio

30、ns shallbe possible without exceeding pilot force as shown in Table 1.4.5.1.3 Full control shall be maintained when retracting andextending flaps within their normal operating speed range (VSOto VFE).4.5.1.4 Lateral, directional, and longitudinal control shall bepossible down to VSO.4.5.2 Longitudin

31、al Control:F22450724.5.2.1 With the airplane trimmed as closely as possible forsteady flight at 1.3VS1, it must be possible at any speed between1.1VS1and 1.3VS1to pitch the nose downward so that a speednot less than 1.3VS1can be reached promptly. This must beshown with the airplane in all possible c

32、onfigurations, withsimultaneous application of full power and nose down pitchcontrol, and with power at idle.4.5.2.2 Longitudinal control forces shall increase with in-creasing load factor.4.5.3 Directional and Lateral Control:4.5.3.1 It must be possible to reverse a steady 30 bankedcoordinated turn

33、 through an angle of 60, from both directions:(1) within 5 s from initiation of roll reversal, with the airplanetrimmed as closely as possible to 1.3VS1, flaps in the takeoffposition, and maximum takeoff power; and (2) within 4 s frominitiation of roll reversal, with the airplane trimmed as closelya

34、s possible to 1.3VSO, flaps fully extended, and engine at idle.4.5.3.2 With and without flaps deployed, rapid entry into, orrecovery from, a maximum cross-controlled slip shall notresult in uncontrollable flight characteristics.4.5.3.3 Lateral and directional control forces shall not re-verse with i

35、ncreased deflection.4.5.4 Static Longitudinal Stability:4.5.4.1 The airplane shall demonstrate the ability to trim forsteady flight at speeds appropriate to the climb, cruise, andlanding approach configurations; at minimum and maximumweight; and forward and aft CG limits.4.5.4.2 The airplane shall e

36、xhibit positive longitudinal sta-bility characteristics at any speed above VS1,uptothemaximum allowable speed for the configuration being inves-tigated, and at the most critical power setting and CG combi-nation.4.5.4.3 Stability shall be shown by a tendency for theairplane to return toward trimmed

37、steady flight after: (1)a“push” from trimmed flight that results in a speed increase,followed by a non-abrupt release of the pitch control; and (2)a “pull” from trimmed flight that results in a speed decrease,followed by a non-abrupt release of the pitch control.4.5.4.4 The airplane shall demonstrat

38、e compliance with thissection while in trimmed steady flight for each flap and powersetting appropriate to the following configurations: (1) climb(flaps set as appropriate and maximum continuous power); (2)cruise (flaps retracted and 75 % maximum continuous power);and (3) approach to landing (flaps

39、fully extended and engine atidle).4.5.4.5 While returning toward trimmed steady flight, theairplane shall: (1) not decelerate below stalling speed VS1;(2)not exceed VNEor the maximum allowable speed for theconfiguration being investigated; and (3) exhibit decreasingamplitude for any long-period osci

40、llations.4.5.5 Static Directional and Lateral Stability:4.5.5.1 The airplane must maintain a trimmed conditionaround the roll and yaw axis with respective controls fixed.4.5.5.2 The airplane shall exhibit positive directional andlateral stability characteristics at any speed above VS1,uptothemaximum

41、 allowable speed for the configuration being inves-tigated, and at the most critical power setting and CG combi-nation.4.5.5.3 Directional stability shall be shown by a tendencyfor the airplane to recover from a skid condition after release ofthe yaw control.4.5.5.4 Lateral stability shall be shown

42、by a tendency for theairplane to return toward a level-wing attitude after release ofthe roll control from a slip condition.4.5.5.5 The airplane shall demonstrate compliance with thissection while in trimmed steady flight for each flap and powersetting appropriate to the following configurations: (1

43、) climb(flaps as appropriate and maximum continuous power); (2)cruise (flaps retracted and 75 % maximum continuous power);and (3) approach to landing (flaps fully extended and engine atidle).4.5.6 Dynamic StabilityAny oscillations shall exhibit de-creasing amplitude within the appropriate speed rang

44、e (VSOtoVFEflaps extended and VSto VDFflaps retracted).4.5.7 Wings Level StallIt shall be possible to preventmore than 20 of roll or yaw by normal use of the controlsduring the stall and the recovery at all weight and CGcombinations.4.5.8 Turning Flight and Accelerated Stalls:4.5.8.1 Turning flight

45、and accelerated stalls shall be per-formed in both directions as follows: after establishing a 30coordinated turn, the turn shall be tightened until the stall.Afterthe turning stall, level flight shall be regained without exceed-ing 60 of additional roll in either direction. No excessive lossof alti

46、tude, nor tendency to spin, nor speed buildup shall beassociated with the recovery. The rate of speed reduction mustbe constant, and may not exceed 1 kts/s for a turning flightstall, and be 3 to 5 kts/s with steadily increasing load factor foran accelerated stall.4.5.8.2 Both turning flight and acce

47、lerated stalls shall beperformed: (1) with flaps retracted, at 75 % maximum continu-ous power and at idle; and (2) with flaps extended, at 75 %maximum continuous power and at idle (speed not to exceedVFE).4.5.9 Spinning:4.5.9.1 For airplanes placarded “no intentional spins,” theairplane must be able

48、 to recover from a one-turn spin or a 3-sspin, whichever takes longer, in not more than one additionalturn, with the controls used in the manner normally used forrecovery.4.5.9.2 For airplanes in which intentional spinning is al-lowed, the airplane must be able to recover from a three-turnspin in no

49、t more than one and one-half additional turn.4.5.9.3 In addition, for either 4.5.9.1 or 4.5.9.2:(1) For both the flaps-retracted and flaps-extended condi-tions, the applicable airspeed limit and limit maneuvering loadfactor may not be exceeded.TABLE 1 Pilot ForcePilot force as applied to the controlsPitch,N (lb)Roll,N (lb)Yaw,N (lb)For temporary application (less than 2 min):StickWheel (applied to rim)Rudder pedal200 (45)200 (45)100 (22.5)100 (22.5)400 (90)For prolonged application: 23 (5.