ASTM F1910-1998(2018) Standard Specification for Long Barbed Tape Obstacles《长倒刺胶带障碍物标准规范》.pdf
《ASTM F1910-1998(2018) Standard Specification for Long Barbed Tape Obstacles《长倒刺胶带障碍物标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F1910-1998(2018) Standard Specification for Long Barbed Tape Obstacles《长倒刺胶带障碍物标准规范》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F1910 98 (Reapproved 2018)Standard Specification forLong Barbed Tape Obstacles1This standard is issued under the fixed designation F1910; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A num
2、ber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers barbed tape materials andconfigurations used for security barriers.1.2 This international standard was developed
3、 in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Document
4、s2.1 ASTM Standards:2A176 Specification for Stainless and Heat-Resisting Chro-mium Steel Plate, Sheet, and Strip (Withdrawn 2015)3A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for PressureVessels and for General ApplicationsA370 Test Methods and De
5、finitions for Mechanical Testingof Steel ProductsA666 Specification for Annealed or Cold-Worked AusteniticStainless Steel Sheet, Strip, Plate, and Flat BarA764 Specification for Metallic Coated Carbon Steel Wire,Coated at Size and Drawn to Size for Mechanical SpringsF1379 Terminology Relating to Bar
6、bed Tape3. Terminology3.1 Refer to Terminology F1379.4. Classification4.1 Refer to 5.1.8.5. Ordering/Specifying Information5.1 Ordering or specifying barbed tape shall include thefollowing information as per sample specification, or byreferencing item numbers in Tables 1 and 2 (indicate number ofloo
7、ps, if applicable). Material furnished under this specificationshall conform to applicable requirements of current editions ofASTM Standards.NOTE 1The following sample specification is provided to assist whenspecifying or ordering barbed tape material.Actual size and style will varyby individual job
8、 requirements.Sample Specification OnlyBarbed tape obstacle shall be 30 in.diameter (62 in.). Each loop shall consist of 24 (61) clusters of fourneedle-sharp barbs on 4 in. centers, each barb measuring a minimum of1.2 in. in length. The barbed tape shall be fabricated from Series 430stainless steel
9、with optional hardness. The barbed tape shall be perma-nently coldclenched over an austenitic mechanical spring core wire. Thewire shall have a diameter of 0.098 in. with a minimum tensile strength ofapproximately 140 psi. The barbed tape shall have a minimum 230 wrapabout the core wire. Adjacent al
10、ternate loops shall be clipped together infive (5) locations around the circumference to obtain the concertina effect.Clip spacing of the extended coil shall be 12 6 2 in. Clips shall be capableof withstanding a minimum pull load of 200 lb. Each coil shall contain 51loops and cover 25 6 1 ft.5.1.1 Q
11、uantityThe number of units of barbed tape re-quired. For fixed length units, the length per unit should bespecified.5.1.2 Description Barbed tape shall be described as singlecoil helical, single coil concertina, double coil concertina, ordouble coil helical.5.1.3 DiameterThe purchaser shall specify
12、the packageddiameter. When double coil products are specified, the innerand outer coil packaged diameters shall be given.5.1.4 Barb LengthRefer to Terminology F1379 and Tables1 and 2.5.1.5 Coil LoopsThe number of coil loops shall be speci-fied by the purchaser.5.1.6 Unit LengthThe purchaser shall sp
13、ecify the installedlength and coil spacing, including the coil spacing tolerance.5.1.7 Number of attachment points, in accordance withTerminology F1379 and Tables 1 and 2.5.1.8 Cross SectionsThe purchaser shall specify the crosssections in accordance with Terminology F1379.6. Material6.1 Composition
14、Barbed tape shall be manufactured fromstainless and galvanized steel in accordance with the ASTM1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edition approved March
15、1, 2018. Published March 2018. Originallyapproved in 1998. Last previous edition approved in 2013 as F1910 - 98(2013).DOI: 10.1520/F1910-98R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards vo
16、lume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international st
17、andard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1TAB
18、LE 1 Stainless Steel Long Barbed Tape (Reinforced) (See Terminology F1379, Figs. 2 and 3)NOTE 1Maximum barb point radius = 0.005 in.NOTE 2Minimum barb length = 1.2 in.NOTE 3Maximum barb spacing=4in.Item Num-berDescription Barbed Tape Ma-terialCore-Wire Material Barb ClustersPer LoopCoil Loops Coil L
19、oop Spac-ing 2.0 in.Coil Length, ft AttachmentPointsHelical1 18 in. Single CoilHelical430 SS 0.025 in.Thick0.098 SS 300 Series140 KSI (965 MPa)13 33 12 in.18 in.3350002 18 in. Single CoilHelical430 SS 0.025 in.Thick0.098 GalvanizedSteel Class III13 33 12 in.18 in.3350003 18 in. Single CoilHelical430
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF191019982018STANDARDSPECIFICATIONFORLONGBARBEDTAPEOBSTACLES 倒刺 胶带 障碍物 标准规范 PDF

链接地址:http://www.mydoc123.com/p-536011.html