ASTM F1141-2010 Standard Specification for Wallcovering《墙壁覆盖材料标准规范》.pdf

《ASTM F1141-2010 Standard Specification for Wallcovering《墙壁覆盖材料标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1141-2010 Standard Specification for Wallcovering《墙壁覆盖材料标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1141 10Standard Specification forWall Covering1This standard is issued under the fixed designation F1141; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates th

2、e year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the performance, quality, pack-aging, and marking characteristics of flexible wall covering asa finished product.1.2 The values stated in inch-

3、pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:2F793 Classification of Wall Covering by Use Characteris-tics3. Terminolo

4、gy3.1 Definition:3.1.1 wall coveringa flexible product designed to coverwalls and ceilings for decorative or functional purposes, orboth.3.2 Definitions of Terms Specific to This Standard:3.2.1 backing (substrate)material upon which facing (oran intermediate layer) is applied. Backing is that materi

5、alwhich is adhered to the wall.3.2.2 biaspattern running off true horizontal or verticalplane.3.2.3 bolta continuous amount of packaged material con-taining the amount specified on the label.3.2.4 facingdecorative material which is applied to anintermediate layer or backing.3.2.5 finished productwal

6、l covering offered to a consumerfor installation.3.2.6 intermediate layermaterial, if any, between thefacing and the backing.3.2.7 lot (batch)the product from a continuous manufac-turing run having the same appearance and characteristic frombeginning to end.3.2.8 pattern matchthe meeting of all part

7、s and colors ofa pattern at the seams of adjacent strips.3.2.9 pattern repeatthe vertical distance between adjacentmatch points of a pattern.3.2.10 protective layerany material applied to the facingto enhance performance.3.2.11 registerthe designed meeting of all parts and colorsof a pattern.3.2.12

8、runa unit of production which may include morethan one lot.3.2.13 secondsfinished material not meeting the qualitycriteria in accordance with Classification F793 and this speci-fication.3.2.14 selvagean undecorated edge which must betrimmed away to allow for correct pattern match or uniformcontinuit

9、y of color.3.2.15 waste edgea decorated edge that must be trimmedaway to allow for correct pattern match or uniformity of color.3.2.16 Shading:3.2.16.1 color variation difference within the same lot ofwall covering.3.2.16.2 luster variation difference in gloss level withinthe same lot of wall coveri

10、ng.3.2.16.3 texture variationdifference in embossing withinthe same lot of wall covering.3.2.17 split bolta bolt consisting of two or three separatelengths of material.4. Appearance4.1 There shall be no appreciable difference in shadingexcept on those finished products in which natural decorativecha

11、racteristics are being simulated. These variances must beclearly stated in writing at the point of purchase. To determinewhether there is an appreciable difference, suspend threesequential 8-ft (2.4-m) strips at eye level in a vertical position,as on the wall, under illumination between 100 to 150 f

12、c (1000to 1500 lx), and view the strips from a distance between 4 and8 ft (1.2 and 2.4 m). An appreciable difference is one which isnoticeable when one strip is compared with the others.1This specification is under the jurisdiction of ASTM Committee F15 onConsumer Products and is the direct responsi

13、bility of Subcommittee F15.15 onWallcoverings.Current edition approved April 1, 2010. Published May 2010. Originallyapproved in 1988. Last previous edition approved in 2009 as F1141 93 (2009).DOI: 10.1520/F1141-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM C

14、ustomer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Wall Preparation and Installa

15、tion5.1 Basic and correct wall preparation instructions, withparticular attention to wall covering which requires specialwall preparation for its proper installation, shall be included insample books and installation instructions.5.2 Installation instructions shall be in or with each bolt andbe read

16、ily accessible to the installer. It shall be the manufac-turers responsibility to notify consumers of proper installationtechniques when new products are introduced.5.3 The manufacturer shall recommend an adhesive, whennecessary, and the products to be used for wall preparation.Recommendation for al

17、ternative adhesives and wall prepara-tion products shall be included in the installation instructions.6. Physical Requirements6.1 Each finished product shall be uniform in physicalproperties, in accordance with Classification F793 and thisspecification.6.2 All facings and protective layers shall be

18、adheredproperly to backings and intermediate layers and the finishedproduct shall be of such quality that delamination does notoccur during normal installation and use.6.3 Finished products shall not chip, peel, or flake duringnormal installation and use. (For test methods to determineconformity wit

19、h this requirement refer to Classification F793.)6.4 There shall be no more than a18-in. (3.5-mm) variancein pattern match between two 8-ft (2.4-m) strips at midpoint.6.5 Wall covering shall be free from all surface flaws,creases, splices, scratches, tears and dirt throughout its entirelength.6.6 Wa

20、ll covering shall be free of wrinkles which cannot beremoved in the course of normal installation.6.7 Finished product shall not shrink or expand after instal-lation when installed in accordance with the manufacturersinstructions.6.8 Pretrimmed material shall be trimmed so that no con-trasting backi

21、ng color will show at the seam when two sheetsare properly installed.6.9 Pretrimmed material shall show no frayed or wavyedges.6.10 All elements of the pattern shall be in register.6.11 The design shall be set at an angle of 90 to thetrimmed edge.6.12 Split bolts narrow goods shall have no piece sho

22、rterthan 9 ft (2.7 m) and shall have an area at least 10 % larger thanspecified on the label. Three lengths are permitted in split boltshaving an area exceeding 100 ft2(9.3 m2). Wide commercialgoods shall have no piece shorter than 3 yd (2.7 m) andone-half linear yard larger than specified on the la

23、bel.6.13 The finished product shall have the necessary charac-teristics to adhere the product to the wall when it is installed inaccordance with the manufacturers instructions. (For testmethods to determine conformity with this requirement refer toClassification F793.)7. Inspection and Testing7.1 Ma

24、nufacturers shall be responsible for testing and in-spection in accordance with this specification and Classifica-tion F793.7.2 The introduction of new products on the market shall bepreceded by thorough testing by the manufacturer underrepresentative field conditions. Manufacturers shall validatela

25、boratory quality control tests against actual field conditions.8. Rejection and Review8.1 It is acceptable for the installer or purchaser to rejectwall covering that fails to conform to the requirements of thisspecification. Rejections shall be reported to the supplierpromptly in person, by phone, o

26、r in writing, or any combina-tion thereof. In the event the supplier is unwilling or unable tosatisfy the complainant, the matter shall be referred to themanufacturer. The inspection and test procedures contained inthis specification shall be used to determine the conformance ofthe product to the re

27、quirements of this specification. Eachmanufacturer who represents a product as conforming to thisspecification shall be permitted to use statistically basedsampling plans that are appropriate for each particular manu-facturing process, but shall keep such essential records as arenecessary to documen

28、t the claim that the requirements of thisspecification have been met.8.2 Any portion of the item not conforming to this specifi-cation shall be clearly marked as seconds if packaged for resaleat retail.9. Certification9.1 When specified in the purchase order or contract, amanufacturers or suppliers

29、certification shall be furnished tothe purchaser stating that samples representing each lot of thematerial have been manufactured, tested, and inspected inaccordance with this specification and the requirements havebeen met.10. Product Marking10.1 Finished products up to 42 in. (107 cm) in width sha

30、llbe labeled with the following information: pattern number, lot(batch) run number, length, width, total area of material(excluding border), supplier name and address and type ofmaterial when appropriate.10.2 Finished products exceeding 42 in. (107 cm) in widthshall be labeled with the following inf

31、ormation: lot (batch),run, length, width, suppliers name and address and type ofmaterial when appropriate.10.3 On a wall covering where direction of hanging isambiguous, the manufacturer shall indicate the proper directionon each separate length.10.4 Bolts classified as seconds shall be prominently

32、labeledas such.10.5 Murals shall be properly numbered for sequence ofsheets. If a numbering sequence is not used, a precise layoutdiagram shall be provided.10.6 A split bolt shall be identified as such.11. Product Packaging and Shipment11.1 The finished products shall be packaged to preventdamage in

33、 shipment.11.2 Shrink wrapping shall not be so tight that it createsproduct damage.11.3 Each case shall not contain more than one split bolt.F1141 10212. Catalog Information12.1 Sample books shall include length, width and squarefootage of each packaged bolt.12.2 Each pattern shall be identified as

34、to proper match andrepeat if any.12.3 Sample book shall state that the product conforms tothis specification.13. Keywords13.1 backing (substrate); bias; bolt; facing; finished product;intermediate layer; lot (batch); pattern match; pattern repeat;protective layer; register; run; seconds; selvage; sh

35、ading andwaste edge; split bolt; wall coveringASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, a

36、nd the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revis

37、ion of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you s

38、houldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F1141 103