ASTM F1117-2003(2013) Standard Specification for Dielectric Footwear《绝缘鞋类的标准规范》.pdf

《ASTM F1117-2003(2013) Standard Specification for Dielectric Footwear《绝缘鞋类的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1117-2003(2013) Standard Specification for Dielectric Footwear《绝缘鞋类的标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1117 03 (Reapproved 2013)Standard Specification forDielectric Footwear1This standard is issued under the fixed designation F1117; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in

2、parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers acceptance testing of dielectricoverfoot and overshoe footwear designed to provide additionalisolation or insulation of

3、 workers if in accidental contact withenergized electrical conductors, apparatus, or circuits.1.2 Three styles of overshoe footwear are provided and aredesignated as rubbers, boots, and galoshes.2. Referenced Documents2.1 ASTM Standards:2F819 Terminology Relating to Electrical Protective Equip-ment

4、for WorkersF1116 Test Method for Determining Dielectric Strength ofDielectric Footwear3. Terminology3.1 DefinitionsDefinitions pertaining to electrical protec-tive equipment may be found in Definitions F819.3.2 Definitions of Terms Specific to This Standard:3.2.1 useras used in 4.3.1, the entity emp

5、loying the actualworker(s) utilizing the equipment; if no separate employer,then the individual.4. Significance and Use4.1 This specification covers the minimum electrical prop-erties of dielectric footwear guaranteed by the manufacturerand the detailed procedures by which such properties are to bed

6、etermined. The purchaser may, at his option, perform or haveperformed these tests in order to verify the guarantee. Claimsfor failure to meet the specification are subject to verificationby the manufacturer.4.2 Electrical contact injuries to workers may involve acurrent path through the feet of the

7、worker. The footwearcovered by this specification is dielectrically rated to provideadditional isolation or insulation to the worker.4.3 Work practices vary from user to user depending uponmany factors. These may include, but are not limited to,operating system voltages, construction design, work pr

8、oce-dures and techniques, weather conditions, etc. Therefore,except for the restrictions set forth in this specification becauseof design limitations, the use and maintenance of this equip-ment is beyond the scope of this specification.4.3.1 It is common practice and the responsibility of the userof

9、 this type of protective equipment to prepare completeinstuctions and regulations to govern the correct and safe use ofsuch equipment.5. Classification5.1 Styles of overshoe footwear covered under this specifi-cation shall be designated as follows:5.1.1 Rubbers, designed to be worn over existing foo

10、twearand to cover only the foot of the worker.5.1.2 Boots, designed to be worn over existing footwear andto cover the foot and lower leg of the worker to below the knee.5.1.3 Galoshes, designed to be worn over existing footwearand to cover the foot and lower leg of the worker to below theknee and ha

11、ving fasteners to close the folded front flaps.6. Ordering Information6.1 Orders for footwear under this specification shouldinclude the following information:6.1.1 Style,6.1.2 Size, and6.1.3 Color.7. Manufacture and Marking7.1 The construction shall be such that the footwear has aspecified minimum

12、dielectric strength when tested as specifiedin Test Method F1116.7.2 Each article of footwear shall be marked clearly andpermanently with the name of the manufacturer or supplier,ASTM F1117, size, and ac voltage rating.7.3 The required information shall be on a label which shallbe applied to either

13、the inside or outside of the footwear in sucha manner as to not affect the dielectric property of the footwear.1This specification is under the jurisdiction of ASTM Committee F18 onElectrical Protective Equipment for Workers and is the direct responsibility ofSubcommittee F18.15 on Worker Personal E

14、quipment.Current edition approved Sept. 1, 2013. Published September 2013. Originallyapproved in 1993. Last previous edition approved in 2008 as F111703(2008). DOI:10.1520/F1117-03R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm

15、.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States18. Electrical Requirements8.1 Each article of overshoe footwear

16、 shall be given a prooftest and shall withstand the 60-Hz ac proof-test voltage (rmsvalue) or the dc proof-test voltage (average value) specified inTest Method F1116.9. Sampling9.1 Each article of footwear in a lot or shipment shall besubject to inspection and test to meet the requirements ofSection

17、s 7, 8.1, and 12.10. Guarantee10.1 The manufacturer or supplier shall replace, withoutcharge to the purchaser, unused footwear which, at any timewithin a period of nine months from date of initial delivery ofshipment to the purchaser or his designee, fail to pass the testsin this specification. This

18、 guarantee will be binding on themanufacturer or supplier only if the footwear have beenproperly stored and have not been subjected to more than anoriginal acceptance test and one retest.10.2 Any acceptance test made by the purchaser, or thepurchasers designee, shall be performed within the first tw

19、omonths of the guarantee period unless otherwise specified.11. Rejection11.1 Individual articles of footwear shall be rejected if theyfail to meet the requirements of Sections 7, 8.1, and 12.11.2 The entire lot or shipment of footwear shall be rejectedif 5 % or more, but not less than two articles o

20、f footwear, in alot or shipment fail to meet the requirements of 8.1.11.3 The testing shall be terminated and the manufacturer orsupplier notified if, during the course of testing, the footwear ina lot or shipment fail to meet the requirements of 8.1 asdetermined by the rejection criteria of 11.2. T

21、he manufactureror supplier may in such a case require the purchaser to submitproof that the test procedure and equipment conform to thisspecification. When such proof has been furnished, the manu-facturer or supplier may request that his representative witnessthe testing of additional footwear from

22、the shipment.11.4 All rejected material shall be returned as directed bythe manufacturer, at his or the suppliers request, without beingdefaced by rubber stamp or other permanent marking.However, those articles of footwear punctured when tested inaccordance with 8.1 shall be stamped, punched, or cut

23、 prior tobeing returned to the supplier to indicate that they lack therequired dielectric property.12. Packaging and Package Marking12.1 Each pair of footwear shall be packed in an individualcontainer of sufficient strength to properly protect the footwearfrom damage in transit. The end of the conta

24、iner shall bemarked with the name of the manufacturer or supplier, style,size, and color.13. Keywords13.1 dielectricASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly a

25、dvised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, eith

26、er reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend.

27、 If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Indi

28、vidual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F1117 03 (2013)2