ASTM E675-2002 Standard Specification for Interchangeable Taper-Ground Stopcocks And Stoppers《可互换的圆锥接地旋塞阀和栓塞的标准规范》.pdf
《ASTM E675-2002 Standard Specification for Interchangeable Taper-Ground Stopcocks And Stoppers《可互换的圆锥接地旋塞阀和栓塞的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM E675-2002 Standard Specification for Interchangeable Taper-Ground Stopcocks And Stoppers《可互换的圆锥接地旋塞阀和栓塞的标准规范》.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: E 675 02Standard Specification forInterchangeable Taper-Ground Stopcocks And Stoppers1This standard is issued under the fixed designation E 675; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision
2、. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 The specification provides standard dimensional r
3、e-quirements for obtaining, within practical limits, interchange-ability in stopcocks and stoppers for ordinary laboratory andindustrial applications. It covers dimensional interchangeabil-ity of the ground surfaces only and does not involve designcharacteristics of the item except where specified.N
4、OTE 1The dimensions pertaining to stopcocks and stoppers weretaken from the Commercial Standard CS 21 of the U.S. Department ofCommerce.NOTE 2Although glass is the most commonly used material forstopcocks and stoppers, other materials may be used as specified.Stopcocks and stoppers constructed from
5、glass should conform to Speci-fications E 438 and E 671.2. Referenced Documents2.1 ASTM Standards:E 438 Specification for Glasses in Laboratory Apparatus2E 671 Specification for Maximum Permissible Thermal Re-sidual Stress in Annealed Glass Laboratory Apparatus2E 920 Specification for Commercially P
6、ackaged LaboratoryApparatus2E 921 Practice for Export Packaged Laboratory Apparatus2E 1133 Practice for Performance Testing of Packaged Labo-ratory Apparatus United States Government Procurement2E 1157 Specification for Sampling and Testing ReusableLaboratory Glassware22.2 U.S. Department of Commerc
7、e Standard:CS 21 Interchangeable Taper-Ground Joints, Stopcocks,Stoppers, and Spherical-Ground Joints33. Requirements for Single Straight-Bore Taper-GroundStopcocks3.1 The designations and dimensions for single straight-bore stopcocks shall be as shown in Fig. 1 and Table 1.3.2 TaperAll straight-bor
8、e stopcocks shall have a taper of1 6 0.006 mm of diameter per 10 mm of length (1 to 10).3.3 Master GagesDimensions and tolerances for mastergages shall be as shown in Fig. 2 and Fig. 3, and Table 2 andTable 3. Overall diameter of ring gage shall be approximatelytwice the diameter of the bore at the
9、reference line in thewindow, but not less than 25 mm.1This specification is under the jurisdiction of ASTM Committee E41 onLaboratory Apparatus and is the direct responsibility of Subcommittee E41.01 onApparatus.Current edition approved May 10, 2002. Published August 2002. Originallypublished as E 6
10、75 79. Last previous edition E 675 94 (1998).2Annual Book of ASTM Standards, Vol 14.04.3Discontinued 1979U.S. Department of Commerce, Washington, DC 20234.FIG. 1 StopcockTABLE 1 Single Straight-Bore StopcocksStopcockDesignationDiameter of Plugat Center-Lineof Bore, mmDLength ofShell, 60.5mmEDiameter
11、 ofBore Hole inPlug, mmF1-MA720 1112 3112 12 30 11221 0317 4 341 4520 562 4 6825 52 810 35 56 10AMicro size.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.3.1 Plug GagePlug shall have two short axial lines1806 0.5 apart intersecti
12、ng the reference line for checkinglocation of bore hole. In addition to the two axial lines 180apart intersecting the reference line on the 4 and 6-mm plugs,two additional axial lines shall be provided on each of theseplugs for checking the location of the bore hole of T-bore and120-deg bore stopcoc
13、ks. These two additional axial lines shallbe placed 90 and 120 (6 0.5) from one of the first two axiallines.3.3.2 Ring GageThe central milled recess, or window,shall be placed approximately midway between the ends of thering gage. Width of recess measured parallel with the axis shallbe approximately
14、 one fourth of the length of the ring, and thewidth of the opening at the inner surface of ring, measuredperpendicular to the axis, shall not exceed one fourth of thelength of the ring. Reference line in recess shall be placedapproximately midway between ends of ring gage.3.3.3 Fit of Product in Wor
15、king Gages The product (bothinner and outer members) shall fit the corresponding workinggages so that the centerline through the bore corresponds withthe reference line on the gage within 6 0.3 mm for 1, 112 , and2-mm bores;6 0.5 mm for 3 and 4-mm bores; and 6 1.0 mmfor 5-mm and larger bores.4. Requ
16、irements for Single Oblique-Bore Stopcocks4.1 Design, dimensions, and tolerances for 1, 112 ,2,3,and4-mm oblique-bore stopcocks shall be as shown in Fig. 4 andTable 4.4.2 TaperAll single oblique-bore stopcocks shall have ataper of 1 6 0.006 mm of diameter per 10 mm of length (1 to10).4.3 Master Gage
17、sThe dimensions and tolerances for mas-ter gages shall be as shown in Fig. 5 and Fig. 6 and Table 5 andTable 6. The overall diameter of the ring gage shall beapproximately twice the diameter of the bore at its midpoint,but not less than 25 mm.4.3.1 Plug GageThe upper circumferential reference linesh
18、all be the gaging point. Each reference line shall have a shortaxial line intersecting it, the two axial lines being on oppositesides of the plug and in the same plane running through the axis(180 6 0.5 apart) for checking location of bore holes.FIG. 2 Master Plug Gage for Single Straight-Bore Stopc
19、ocksFIG. 3 Master Ring Gage for Single Straight-Bore StopcocksTABLE 2 Master Plug Gages for Single Straight-Bore StopcocksStopcockDesignationLength of TaperedPortion +2.0 mm,0 mmEEDiameter atGaging Point60.003 mmDDDistance fromLarge End ofTapered Portionto GagingPoint, mmNN1-MA32 7 20142 12 5112 42
20、12 2524 2352 17 3045556 20 265 3864 5 610 68 35 38AMicro size.TABLE 3 Master Ring Gages for Single Straight-Bore StopcocksStopcockDesignationLength ofRing, +0.2mm, 0 mmEEInside Diameterat Gaging Point,60.003 mmDDDistance fromTop to GagingPoint, mmNN1-MA20 7 101301215112 30 12 15340172045 42022648522
21、52610 56 35 28AMicro size.E6750224.3.2 Ring GageThe width of the milled recesses, orwindows, measured parallel with the axis shall be approxi-mately one fourth of the length of the ring, and the width of theopening at the inner surface of ring, measured perpendicular tothe axis, shall not exceed one
22、 fourth of the length of the ring.The recesses shall be so placed that the reference lines fallapproximately midway in the recess.4.3.3 Fit of Product in Working Gages The product (bothinner and outer members) shall fit the corresponding workingFIG. 4 Single Oblique-Bore StopcockTABLE 4 Single Obliq
23、ue-Bore StopcockStopcockDesignationDiameter of Plug atGaging Point, mmDLength of Shell,60.5 mmEDiameter of Borein Plug, mmFDistance from Large Endof Shell to GagingPoint, 60.5 mmNDistance betweenBore Holes,PA1 12.60 40 1 14.0 12112 12.60 40 112 14.0 122 12.60 40 2 14.0 123 17.35 50 3 16.5 174 17.35
24、50 4 16.5 17ASee 3.3.3.FIG. 5 Master Plug Gage for Single Oblique-Bore StopcocksFIG. 6 Master Ring Gage for Single Oblique-Bore StopcocksE675023gages so that the centerlines through the openings correspondwith the reference lines on the gages within 6 0.3 mm for 1,112 , and 2-mm bores, and 6 0.5 mm
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTME6752002STANDARDSPECIFICATIONFORINTERCHANGEABLETAPERGROUNDSTOPCOCKSANDSTOPPERS 互换 圆锥 接地 旋塞 栓塞 标准规范

链接地址:http://www.mydoc123.com/p-533289.html