ASTM E2568-2009e1 Standard Specification for PB Exterior Insulation and Finish Systems《PB外部加隔热层和装饰面的标准规范》.pdf
《ASTM E2568-2009e1 Standard Specification for PB Exterior Insulation and Finish Systems《PB外部加隔热层和装饰面的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM E2568-2009e1 Standard Specification for PB Exterior Insulation and Finish Systems《PB外部加隔热层和装饰面的标准规范》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: E 2568 091Standard Specification forPB Exterior Insulation and Finish Systems1This standard is issued under the fixed designation E 2568; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A num
2、ber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorial changes were made throughout to comply with ASTMs policy on Units in Standards (April 2009).1. Scope1.1 This specification covers PB Ex
3、terior Insulation andFinish Systems (EIFS) defined as an exterior, non-bearing wallcovering providing a weather-resistant exterior wall envelopeon walls required to be combustible or noncombustible, fire-resistance-rated or nonfire-resistance-rated. Further, PB EIFSis a system described as being app
4、lied over expanded polysty-rene or polyisocyanurate insulation board, an adhesive ormechanical attachment of the insulation board to a substrate, orboth, glass fiber reinforcing mesh, a base coat on the face of theinsulation board, and a textured protective finish coat.1.2 This specification does no
5、t cover Class PB EIFS withdrainage.1.3 This specification qualifies EIFS products for use innormal service conditions and is not for evaluating in serviceEIFS installations.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconver
6、sions to SI units that are provided for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices
7、 and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B117 Practice for Operating Salt Spray (Fog) ApparatusC 297/C 297M Test Method for Flatwise Tensile Strengthof Sandwich ConstructionsC 578 Specification for Rigid, Cellular Polystyrene
8、 ThermalInsulationC 1289 Specification for Faced Rigid Cellular Polyisocya-nurate Thermal Insulation BoardD 2247 Practice for Testing Water Resistance of Coatings in100 % Relative HumidityE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE119 Test Methods for Fire Tests of Buil
9、ding Constructionand MaterialsE 330 Test Method for Structural Performance of ExteriorWindows, Doors, Skylights and Curtain Walls by UniformStatic Air Pressure DifferenceE 331 Test Method for Water Penetration of Exterior Win-dows, Skylights, Doors, and Curtain Walls by UniformStatic Air Pressure Di
10、fferenceE 2098 Test Method for Determining Tensile BreakingStrength of Glass Fiber Reinforcing Mesh for Use in ClassPB Exterior Insulation and Finish Systems (EIFS), afterExposure to a Sodium Hydroxide SolutionE2110 Terminology for Exterior Insulation and Finish Sys-tems (EIFS)E 2134 Test Method for
11、 Evaluating the Tensile-AdhesionPerformance of an Exterior Insulation and Finish System(EIFS)E 2485 Test Method for Freeze/Thaw Resistance of Exte-rior Insulation and Finish Systems (EIFS) and WaterResistive Barrier CoatingsE 2486 Test Method for Impact Resistance of Class PB andPI Exterior Insulati
12、on and Finish Systems (EIFS)G23 Practice for Operating Light-Exposure Apparatus(Carbon-Arc Type) With and Without Water for Exposureof Nonmetallic Materials (Discontinued 2001)3G26 Practice for Operating Light-Exposure Apparatus(Xenon-Arc Type) With and Without Water for Exposureof Nonmetallic Mater
13、ials (Discontinued 2001)3G 153 Practice for Operating Enclosed Carbon Arc LightApparatus for Exposure of Nonmetallic MaterialsG 155 Practice for Operating Xenon Arc Light Apparatusfor Exposure of Non-Metallic Materials1This test method is under the jurisdiction of ASTM Committee E06 onPerformance of
14、 Buildings and is the direct responsibility of Subcommittee E06.58on Exterior Insulation and Finish Systems (EIFS).Current edition approved April 1, 2009. Published May 2009. Originallyapproved in 2007. Last previous edition approved in 2007 as E 2568 07.2For referenced ASTM standards, visit the AST
15、M website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1Copyright
16、ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.2.2 NFPA Standards:4ANSI/NFPA 268 Standard Test Method for DeterminingIgnitability of Exterior Wall Assemblies Using a RadiantHeat Energy SourceANSI/NFPA 285 Standard Fire Test Method for the Eval
17、u-ation of Fire Propagation Characteristics of Exterior,Nonload-bearing Wall Assemblies Containing Combus-tible Components3. Terminology3.1 Definitions are in accordance with Terminology E2110unless otherwise specified.3.2 Definitions of Terms Specific to This Standard:3.3 class PB EIFS, nEIFS where
18、 the base coat varies inthickness depending upon the number of layers, or thickness ofreinforcing mesh. The reinforcing mesh is glass fiber mesh thatis encapsulated by the base coat in accordance with EIFSmanufacturer recommendations. Protective finish coats, ofvarious thicknesses in a variety of te
19、xtures and colors, areapplied over the base coat.3.3.1 DiscussionClass PB EIFS includes foam plasticconforming to either Specifications C 578 or C 1289.3.4 EIFS-related construction, nconstruction that worksin conjunction with the EIFS, but is not part of the EIFS.4. Materials and Manufacture4.1 Pro
20、duct DescriptionThe material and specificationsshall be as specified by the selected EIFS manufacturer andshall be defined as in Terminology E2110except as modifiedherein.5. Performance Requirements5.1 The system and its components shall meet or exceed theperformance standards described in 5.2-5.7 o
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTME25682009E1STANDARDSPECIFICATIONFORPBEXTERIORINSULATIONANDFINISHSYSTEMSPB 外部 隔热层 装饰 标准规范 PDF

链接地址:http://www.mydoc123.com/p-531436.html