ASTM E1273-1988(2003) Standard Specification for Color Coding of Reusable Laboratory Pipets《可重复使用的实验室移液管的色标》.pdf

《ASTM E1273-1988(2003) Standard Specification for Color Coding of Reusable Laboratory Pipets《可重复使用的实验室移液管的色标》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1273-1988(2003) Standard Specification for Color Coding of Reusable Laboratory Pipets《可重复使用的实验室移液管的色标》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E 1273 88 (Reapproved 2003)Standard Specification forColor Coding of Reusable Laboratory Pipets1This standard is issued under the fixed designation E 1273; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of la

2、st revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers a system of color coding forone-mark pipets for identification of nominal capacities, andfor

3、graduated pipets for identification of nominal capacities andunits of sub-division.1.2 This specification applies to one-mark and graduatedpipets of the nominal capacities listed in Table 1 and Table 2,respectively.NOTE 1Many pipets not covered by other ASTM standards areincluded in Table 1 and Tabl

4、e 2, in order, firstly, to ensure uniformity ofcolor coding as far as possible for non-standard as well as standard pipetsand, secondly, to reserve suitable codes for possible future standards forother types of pipet.2. Referenced Documents2.1 ASTM Standards:E 1157 Specification for the Sampling and

5、 Testing of Reus-able Laboratory Glassware23. Significance and Use3.1 The purpose of this specification is to ensure that if acolor code is used on pipets, all manufacturers will use thesame code; it is not intended as an encouragement of colorcoding if this is not required.4. Color Properties4.1 Co

6、dingThe color coding used on one-mark pipetsshall be in accordance with Table 1, and graduated pipets shallbe in accordance with Table 2.4.2 VariationsVariations in the enamels used in the meth-ods of application appropriate for pipets made from differenttypes of glass inevitably result in minor var

7、iations of color, andit is therefore not appropriate to specify closely the sevencolors listed in the tables.5. Marking Requirements5.1 The color code shall take the form of color bandsextending at least 150 around the circumference of the pipetand situated not more than 70 mm from the top of the pi

8、pet andnot less than 20 mm above the nearest graduation line.5.2 For a code consisting of a single band of color, the bandshall be 5 to 10 mm wide. For a code consisting of two bandsof color, each band shall be 3 to 5 mm wide and the two bandsshall be separated by a space of 2 to 3 mm. Color bands d

9、o nothave to be continuous but may be broken as long as they cover40 % of the circumference of the pipet.1This specification is under the jurisdiction of ASTM Committee E41 onLaboratory Apparatus and is the direct responsibility of Subcommittee E41.01 onGlass ApparatusCurrent edition approved Oct. 3

10、1, 1988. Published December 1988.2Annual Book of ASTM Standards, Vol 14.02.TABLE 1 Coding System for One-Mark PipetsNominal Capacity, mL Color Code Bands0.001 1 blue0.002 2 red0.003 1 yellow0.004 2 green0.005 1 white0.01 1 orange0.015 2 blue0.02 1 black0.025 2 white0.03 2 yellow0.035 2 black0.04 2 r

11、ed0.05 1 green0.075 2 orange0.1 1 blue0.15 1 white0.2 1 red0.25 2 green0.3 1 yellow0.4 2 red0.5 2 black1 1 blue2 1 orange3 1 black4 2 red5 1 white6 2 orange7 2 green8 1 blue9 1 black10 1 red15 1 green20 1 yellow25 1 blue30 1 black40 1 white50 1 red75 1 green100 1 yellow150 2 black200 1 blue1Copyrigh

12、t ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.NOTE 2Pipets calibrated to deliver by blowing out the last drop shallbe identified by a wide band or two narrow bands permanently marked ontheir top end.6. Sampling and Testing6.1 Sampling and t

13、esting shall be in accordance with Speci-fication E 1157.7. Keywords7.1 colorcoding; laboratory; pipetsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that d

14、etermination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved

15、 or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel

16、that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprin

17、ts (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 2 Coding System for Graduated PipetsNominal Capacity, mL Sub-division, m

18、L Color Code Bands0.01 0.001 1 blue0.05 0.001 1 yellow0.1 0.001 2 green. 0.005 1 red. 0.01 1 white. 0.05 2 orange0.125 0.0125 2 yellow0.2 0.001 2 blue. 0.002 2 white. 0.01 1 black. 0.1 1 orange0.5 0.005 1 green. 0.01 2 yellow. 0.02 2 red. 0.05 2 black. 0.25 2 green1 0.01 1 yellow. 0.05 2 green. 0.1 1 red1.5 0.01 2 red2 0.01 2 white. 0.02 1 black. 0.05 2 orange. 0.1 1 green3 0.01 2 blue5 0.05 1 red. 0.1 1 blue10 0.1 1 orange15 0.1 2 green20 0.1 2 yellow25 0.1 1 white. 0.2 1 green50 0.1 2 orange. 0.2 1 black100 0.2 1 redE 1273 88 (2003)2