ASTM E1093-1991(2012) 6250 Standard Specification for Glass Prothrombin Pipet Disposable《一次性的凝血酶原玻璃吸管的标准规范》.pdf
《ASTM E1093-1991(2012) 6250 Standard Specification for Glass Prothrombin Pipet Disposable《一次性的凝血酶原玻璃吸管的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM E1093-1991(2012) 6250 Standard Specification for Glass Prothrombin Pipet Disposable《一次性的凝血酶原玻璃吸管的标准规范》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: E1093 91 (Reapproved 2012)Standard Specification forGlass Prothrombin Pipet, Disposable1This standard is issued under the fixed designation E1093; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi
2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers a glass disposable Prothrombinpipet suitable for use in micro techniques for estimation ofProthrombin t
3、ime.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This precautionary statement pertains only to the testmethod portion, Section 8, of this specification. This standarddoes not purport to address all of the safety conce
4、rns, if any,associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2. Referenced Documents2.1 ASTM Standards:2E438 Specification for Glasses in Laboratory
5、Apparatus2.2 ISO Standard:31769 Laboratory GlasswarePipettesColor Coding3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 accuracythe expected distribution of mean volumesaround the stated volume.3.1.2 coeffcient of variationthe expected distribution ofindividual volumes around
6、the mean volume.3.1.3 disposableProthrombin pipets which are intended tobe used once only and then discarded.NOTE 1Such pipets will only be expected to provide their specifiedperformance during the original operation.4. Classification4.1 This specification covers only one glass pipet as illus-trated
7、 in Fig. X1.1.5. Materials and Manufacture5.1 The pipet shall be made of borosilicate glass, Type 1;Class B, or soda lime glass, Type 2, in accordance withSpecification E438.6. Physical Properties6.1 DesignThe Prothrombin pipet shall be made of onepiece construction glass tubing that is straight and
8、 with uniformbore and lightly firepolished on both ends. The pipet shall bemade to the dimensions as specified in Fig. X1.1.6.2 DimensionsThe pipet shall be made of tubing with aminimum outside diameter (o.d.) of 2.3 mm with an insidediameter (i.d.) of 1.7 mm. The uniformity of the bore shall be60.0
9、5 mm throughout the straight portion of the pipet. Thepipet shall be a minimum of 160 mm long.6.3 CapacityThe pipet shall be calibrated “to deliver”(T.D.) 0.1 and 0.2 mL at 20C. Marking shall be as specified in6.5.6.3.1 Accuracy (see 3.1.1)The accuracy from stated vol-ume shall be 62.0 % for the 0.1
10、 and 0.2-mL capacity and shallbe determined as specified in 8.1.6.3.2 Coeffcient of Variation (see 3.1.2)The coefficient ofvariation from stated volume for the 0.1 and 0.2-mL capacityshall not exceed 2.0 % and shall be determined as specified in8.1.6.4 Graduation LinesThe pipet shall be calibrated a
11、ndmarked with graduation lines at 0.1 and 0.2 mL from the tip ofthe pipet. The graduation lines shall be 0.3 6 0.1 mm and shallcompletely encircle the tube.6.5 Pipet NomenclatureThe pipet shall be marked with0.1 and 0.2-mL markings slightly above the graduation lines.The pipet may be marked with the
12、 inscription T.D. 20C, or themanufacturers or vendors name or trademark, or both.6.6 Blow-out DeliveryThe Prothrombin pipet is designedas a dual delivery system for the determinations of coagulationassays. When utilizing the 0.2 mL calibration line, the tip of thepipet should contact the wall of the
13、 receiving vessel and allowthe pipet to drain freely. The remaining quantity of liquid is to1This specification is under the jurisdiction of ASTM Committee E41 onLaboratory Apparatus and is the direct responsibility of Subcommittee E41.01 onApparatus.Current edition approved Nov. 1, 2012. Published
14、November 2012. Originallyapproved in 1986. Last previous edition approved in 2005 as E1093 91 (2005).DOI: 10.1520/E1093-91R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information,
15、 refer to the standards Document Summary page onthe ASTM website.3Available from ISO, 1 Rue de Varembe, Case Postal 56, Crt 1221, Geneva 20,Switzerland.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1be blown out into the center of th
16、e receiving vessel. Whenutilizing the 0.1 mL calibration line the contents are to bevigorously blown out into the center of the receiving vesselwith one quick effort. Either one band or two narrow bandsshall encircle the top end of the pipet to signify the contentsmust be blown out as shown in Fig.
17、X1.1.6.7 Color CodingThe pipet shall be color coded forcapacity as specified in ISO Standard 1769 with an “orange”color band that is 6 6 2 mm wide and located 16 6 2 mm fromthe top of the pipet as shown in Fig. X1.1.6.8 Marking PermanencyGraduation lines, inscriptions,and numerical markings on the p
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTME1093199120126250STANDARDSPECIFICATIONFORGLASSPROTHROMBINPIPETDISPOSABLE 一次性 凝血酶原 玻璃 吸管 标准规范 PDF

链接地址:http://www.mydoc123.com/p-527893.html